Recently reset a Linksys Router. The only settings I changed were the name of the Router, the password, and the security settings to WPA2. My computer is able to connect to the router and has internet access. However, my cell phone is able to connect to the router/wireless network successfully but the internet is not workingIs their a setting on the router that I need to change to ensure that my cell phone can access the internet
View 1 RepliesI have the WAP11 serial number G3110320414 that does not have a reset switch in the back. How do I get back to factory settings?
View 3 Replies View RelatedI previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
How can I reset the static DNS ip address back to 0.0.0.0 ?
My linksys router reset itself. Yes it reset itself. It resets to default paramaters. I had to change the router parameters in the webpage with the wired connection to the router. That works fine, but after a day or say it comes back to default again. I am going crazy, I am sure nobody is pressing the little button on the router. Do I have virus or something or maybe the router is going bad. It's a WRT54G.
View 2 Replies View RelatedI'm trying to setup my linksys e1000 router as an access point and I cant figure out how to log in to it to change its settings. I've done every reset procedure I can think of but when I power it up it still shows up as a "security enables network".
View 5 Replies View RelatedHow will I reset WRT 160N?
View 1 Replies View RelatedHow To Reset E2500 Router
View 1 Replies View RelatedI want to use my router to boost the signal to the 2nd floor of my house, and Im having some problems.When I connect my router to the web application to change restore it to manufaturer setting the router keeps broadcasting my old SSID. The laptops in the house pick up that signal. I want to reset my router so it can broadcast my new network.
View 2 Replies View RelatedI recently set up a wrt54g router that I got used from a friend. I pressed the 'reset' button on the back, configured it for my computer according to the instructions on the website, and everything worked fine for a couple of days. Then I lost connectivity, tried powercycling my modem, but had to reset and reconfigure the router again. Worked fine again for a couple of days, then the problem repeated itself, so I reset and reconfigured again.
View 1 Replies View RelatedThis router was given to me without any documentation. No one knows what the password is for the wifi or web interface. I have tried to reset the router to factory defaults without any luck. I have tried regular reset method and 30/30/30 and still it is holding on to the custom settings. Here is what I know:
1. The router can be pinged without any errors.
2. The logon screen comes up requesting username and password. I have tried all of the default inputs (blank/admin, admin/admin).
3. The wireless is working and the SSID is Linksysxx.
4. I tried the following:at the DOS prompt typed cd then, TFTP -i 192.168.1.1 PUT (my fw).binunplugged the router, plugged in and hit "Enter"After about 15 seconds I got the error message, "Invalid Password". I tried this again and got the same results.I know the router is working, but I can not get it for go back to factory settings.
I am facing issue with my cisco wireless E1000, the wireless connection on the laptop reset on its own. Its like there is a timer and it reset's the wireless connection after some time. I was unable to measure the time after which it resets but its happening too frequently causing multiple internet apps to fail example if I am downloading something it will fail as the internet connection is reset. The firmware I am running on the rotuer is 2.0.01 and I have configured DHCP on the LAN, I am experiencing this problem with 3 laptop that I use at home which uses both G and N networks.
View 2 Replies View RelatedOk, so I reset the router but i still can't login to the setup using the factory password (admin/admin) (blank/admin) (admin/blank). Now I have an unencrypted network and no access to the setup... I even tried using the setup CD but it doesn't recognize the router.
View 2 Replies View RelatedMy EA6500 has been working fine for the last few months but a few days ago i upgraded to the latest firmware 1.1.28.147876 - this was done by an ethernet cable, not by wifi. However i've noticed the router reverts back to the previous fw 1.1.28.146856 when the router is rebooted or factory reset. I've repeated the fw upgrade process and also done a hard reset before upgrading the firmware but no avail. Normally after firmware is 'upgraded' the router reboots and i get the message "firmware successfully installed" but then on subsequent reboots the firmware reverts back. I'm using local router access but even using smartwifi gives the same issue. When upgrading fw, i've tried both options online & manual but again makes no difference.
Don't really fancy calling Linksys support and going through 4 hrs of basic trouble shooting. Or perhaps Cisco have introduced a new automatic firmware downgrade option in their routers?
How to reset the linksys cisco wrt120n router.
View 4 Replies View RelatedI can't seem to login to my admin. the IP for me is 192.168.0.1 and I can't login. I tried resetting the router a few times and no luck.Is there ANY other way to reset the username and password?
View 6 Replies View RelatedI forgot it. How do I either find out what it is, or reset the E1000 so I can create a new one? (Connection now working fine. Held the reset button for 30 seconds, and conmnection pops right up again.
View 4 Replies View Relatedi'm attempting to access the router's configuration options (192.168.1.1) and it's requesting a user and a password, i have not set any of them so i'm using the defaults, been, user (blank), password (admin) but is not taking them; after 3 attempts it gives me a 404 error.
View 6 Replies View RelatedI have a wrt120n router. It will not give IP addresses after 24 hours of usage. Having to reset the router to be able to get connectivity is getting to be very aggravating.
View 2 Replies View RelatedI have changed the router username/password in the past and either I can't remember it or its not accepting what I am entering, because the router logon will not go through. I have unplugged the router for 5 mins and then let it come back on and still cant get in, pressed the reset button down and let it come back up still nothing, and I have unplugged the cable modem and router for five mins and then plugged them both back up and I still can't get the router to reset to the default admin password. In the past it has worked before but now nothing I try will let me into the router interface to set up anything.
View 4 Replies View RelatedI got a problem with my router CISCO (DPC3825) where the eithernet is working properly and the wireless is not, and I had to plug the usb to make the setups, and suddenly the wireless was working but when I tried to reset the password something worng happened change the set of the wireles
View 2 Replies View Relatedhow to reset password on a WRT54G2?
View 3 Replies View RelatedI have an E3200 router and need to know how to reset the password... cant connect my tablet because it asks for cisco connect password and I have NO CLUE what it is... if i do the reset on bottom of my router will it let me reset my password???
View 3 Replies View RelatedI need my password reset on my Linksys cisco E1000
View 2 Replies View RelatedMy sone pushed the reset button and now I cannot get the router to work. I can only connect to the internet if I am connected directly to my modem... the router does not recognize my computer (corresponding # does not light up on the the router). I have tried disconnecting everything and reconnecting everything but it doesn't work.I am using Windows7. How I can begin using the router again? (My knowledge with this I have had it for almost 2 years and is out of warranty... What can I do so I don't have to buy a new one?
View 4 Replies View Relatedim trying to reset my linksys WRT54G wireless router because im trying to change some settings. i tried the 192.168.1.1 and it asks for a password, but i dont remember putting one on....i tried the admin in the password field and empty name field but that dosent work.I've tried holding the reset button on the router itself for 10sec+ but that dosen't seem to do anything.
View 9 Replies View RelatedI am considering buying the new router with the new wireless ac ability, but wanted to ask a couple questions first.1. If I have the router bridge combo that utilizes the 5 mghz bandwidth, but also have older devices that run only on the 2.4 ghz frequency, will the router work both frequencies or will it change to 2.4 only? Like with mixed N that has a device that is g.2. Will all my older devices work without upgrading wireless cards?3. If I use the bridge in a seperate room, approximately 30 feet away with 1 wall in between should my speeds stay pretty high?I am planning to get the special they are offering for the 6500 plus the bridge, that gives the 50 dollar debt card, not sure of bridgemod3l number but think only one Iis available in that deal. So sick of my wrt330n needing to be reset 3 times a day.
View 1 Replies View RelatedI am facing issue with my cisco wireless E1000, the wireless connection on the laptop reset on its own. Its like there is a timer and it reset's the wireless connection after some time. I was unable to measure the time after which it resets but its happening too frequently causing multiple internet apps to fail example if I am downloading something it will fail as the internet connection is reset. The firmware I am running on the rotuer is 2.0.01 and I have configured DHCP on the LAN, I am experiencing this problem with 3 laptop that I use at home which uses both G and N networks.
View 4 Replies View RelatedI am trying to setup two wireless routers in my network. I purchased a E1200 N router and an older G Linksys router upstairs.When I got the N router I set it up a stand alone router and it worked great for a week or so. I then wanted to try to get both routers going to I changed the IP address on E1200 to 192.168.2.1....the router rebooted and then could not login. I am not able to get any internet conntion anymore. When I type 192.168.2.1 it goes to page can not be displayed, 192.168.1.1 same thing. Ipconfig shows some address auto address that I did not put in and i am also not connected to a modem. I cant log into the router at all.So reset: I held down the button for 30 seconds...let go and it blinks and then goes solid but does not reset. Unplugged router for 5 minutes tried again. Cant get into 192.168.1.1..will not prompt for anything. I have tried to reset this router about 10 times and can not get into the default login at all.
View 1 Replies View RelatedMy wireless was working but would load some pages super slow and others just fine. I reset my modem and router and now I can wireless connect to the router but get no connection. If I plug my computer directly to the modem I can connect the internet just fine. But if I hook up my router and connect it to my pc through a cable it can't connect just like the wireless.I have a linksys WRT54GSv1 Comcast is my ISP I ran Xirrus connection test and it said DNS Lookup Failure then No IP Availible.This is an ipconfg /all result
Code:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Users**********>ipconfig /all
[code]....
I have a Linksys wireless router WRT160N, and its worked fine for the past year, till last night, when I pushed the reset button trying to solve another issue and now my router isnt working. I ran Linksys setup disc and it said I was all up and running, but still cant get online with my laptop through the router.I am at a point where I have my default gateway address 192.168.1.1 and my IP address, but not sure what to do with that to get this issue corrected.
View 14 Replies View Relatedi was having issues with one of my devices after a power outage. all my other devices worked (laptops, xbox, iphones, etc)i thought doing a reset on the router would get the odd device working again but all it did was mess up my internet. i don't have the key or cd any longer from when i set it up.
View 9 Replies View RelatedWe recently exchanged our old WRT54G with the current model WRT54GL. Unfortunately we have to reset the WRT54GL router a few times per week. We noticed that when one of the clients -- an iPod Touch -- is not being used on the wireless network (that person being away), the router runs without failing. I would suppose router reliability should not depend on the clients that it serves. Is anybody familiar with a similar problem? Is there a way to prevent the router from failing so
View 5 Replies View RelatedHow to reset my router to factory settings so i can install it on a new computer
View 2 Replies View Related