Wireless Router Is Not Putting Out A Signal?

Nov 7, 2011

I have a Dell Wireless Router, yes I know terrible lmao but was free a laptop I bought my sister. Anyways, it does not seem to be putting out a wireless signal.However if hook an ethernet cord from the modem, to my parents pc, eliminating the router completely, the internet works, this is how the set up usually is. I have my pc upstairs with a wireless card and have never had problems until now.When I hook up the wireless router, the internet light, lights up etc. But on the main computer that is hardwired, loses internet. It just has "Limited Connectivity".I tried resetting, powering off, restarting. I tried to set up a new wireless network and the computer cannot find any wireless devices. My computer upstairs cannot find a wireless network either.We also have a wireless "Roku" box which is netflix, this works off wi-fi, but this also cannot get a wireless connection.

Ive tried typing in the routers ip just guession that is the 192.168.1.1, I have tried a bunch of others but cannot get into my routers settings. I am trying to get into those router settings thru my browser, Im trying to figure out the ip. However if I hook my router up I lose internet so i am un-able to do that.I build PC's and service them, but networking is where my expertise end.

View 2 Replies


ADVERTISEMENT

Linksys Router Does Not Seem To Putting Out Signal

Jan 12, 2011

The laptops that normally run from the Linksys network are not showing any network at all. The "Easy Link Advisor" says the network is working.

View 2 Replies View Related

How To Restrict Router By Putting In Password

Jan 9, 2011

How to restrict my Router by putting in a Pass word so my neighbours could be stopped using my highspeed internet and thus makinit weaker for my household.

View 3 Replies View Related

Cisco WAN :: NAT / Access After Putting 5512 ASA Behind RV180 Router

Feb 12, 2013

Previously we had a 5512 ASA setup and working properly. We had several internal address static nat'd to external address and were able to access our servers externally. Unfortunatley, when it came time to setup our site to site vpn we found out our ISP was blocking the necessary traffic on the IP we were using for the ASA's outside interface. We ended up having to buy a RV180 to act as a dummy router to assign the restricted IP to on its outside interface and put the ASA behind it so we could assign it an unrestricted IP for it's outside interface for the site to site vpn.
 
 The problem is our NAT and access rules are no longer working. Internet access works fine however. We haven't even set the site to site vpn stuff up yet either. What do we need to change in either the ASA or the router to get this working again. I don't even know where to begin with providing any pertinent information for diagnosing the problem.

View 1 Replies View Related

Cisco Wireless :: Putting A Certificate On 5508 WLC For Webauth?

Feb 12, 2013

I am using webauth and need to install a SSL cert to prevent the "There is a problem with this website's security certificate" message. I have a Wildcard cert that was issued by Network Solutions that I use on a couple web servers I run, and want to know if I can use that for the WLC? It's a pks cert and I think the WLC needs to use a pem cert, so I converted the wildcard to pem. Or do I need to purchase a cert that is not a wildcard and is in pem format?

View 7 Replies View Related

Cisco Wireless :: Putting 1141 AP In Repeater Mode With AP HP Procurve?

Oct 5, 2011

I have a problem putting a Cisco 1141 AP in repeater mode with a AP HP Procurve.Root AP is a the Procurve, but when try to put the Cisco AP with same SSID, Authentication, etc, I receive this error:
 
%DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: NO Aironet Extension IE
 
I try disable the Aironet Extensions and always get the same error all time. It's possible connect both APs?

View 6 Replies View Related

Cisco Wireless :: Putting Aironet AP1042 / AP1142 In Plastic Enclosure Box?

Nov 6, 2011

I would like to know if it is feasible to put those Aironet AP with internet antenna like AP1142 / AP1042 in a enclosure box (Like IP66 grade) box. Will those enclosure box absorb the Radio signal from the AP? or the Radio signal can still survive after passing the box but the Signal Strength be degraded only?

View 2 Replies View Related

Putting Speed Caps On A Network?

Mar 14, 2011

I am an administrator and my co-worker keeps on going on you tube during work. Is there any way to make his computer only use up 20KB per second instead of 150 KB per second?

View 6 Replies View Related

Cisco Firewall :: Putting Servers Behind ASA5505?

Jan 25, 2012

I am in the process of adding a lot of servers to sit behind our new ASA 5505 (8.4) firewall. At the moment I have added 2 servers and they are both NAT'ed to 2 different public IPs.
 
Server 1     192.168.10.1 -> 80.*.*.1
Server 2     192.168.10.111 -> 80.*.*.6
 
The first server can only be RDP'ed in to using its public IP which is what I want it to do. The second one has most of the service ports open like 443, 80, 110, 25 and etc. However when I try and browse externally to [URL]. I get an " Error 107(net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error." in Google Chrome or any other browser. and the ASA reports:11:27:30192.168.10.111262680.*.*.6443Inbound TCP connection denied from 192.168.10.111/2626 to 80.*.*.6/443 flags SYN  on interface inside and I also get a Land to Land attack detected from 80.*.*.6 to 80.*.*.6
 
Is it worth setting up a DMZ or can I get away with the setup I have?

View 2 Replies View Related

Cisco Routers :: Putting A Vpn Server Behind Rvl200

Jan 6, 2013

rvl200 is not working with any new os/java.  cisco is not fixing and telling us to move on.picked up a vpn server and placed it on the dmz for rvl200 (on 192.168.1.105).  for the life of me, can not get traffic from the outside to go to this server.  tried port forwarding on rvl200 (for 443) which is what the vpn server recommends.  rvl200 is not allowing this.  can not go through the ssl vpn on rvl200 since it does not work.  looked at rv042 topics and it shows similar problems. 

View 1 Replies View Related

Home Network :: Putting Equipment In Server Cabinet

Apr 26, 2011

I just got a server cabinet from a friend and i am going to put all my networking stuff in there i want to put my router inside it too but im not sure if it will affect the signal the cabinet is made out of metal but not thick.

View 2 Replies View Related

Cisco Application :: Putting ACE4710 Into Running System?

Apr 17, 2012

I'm implementing and found out some  issues are unresolvable on ACE4710. This network have been running on a server without LB. Now the second server comes up. We choosed to implement with Routed Mode.This network Peak @ 300Mbps. Now on we're doing the first context which is function as content  web-farm. In near future, 2nd context which takes care of indexing  web-farm when they buy more server.
 
From following diagrams.I browsed from internet into this service. "show service-policy" shown  as '0' (counter was not running). I guessed that there is something  wrong in FW configuration. So I isolated out FW. Then I plugged-in  my PC into network 30 (192.168.30.X) in front of this LB, then browsed  into LB's VIP (192.168.30.1). LB  "show service-policy" came up BUT  there is nothing return to my PC (client). "show conn" on LB as  "SYNSEEN". What's SYNSEEN?! Some meaningful.
 
Then I tried to figure out with a PC running 'apache' and took the  place of real server. "It works!" returned from LB/Server. "show conn"  became 'Establish' Programmer guy said if I browse into web-farm  (i.e. content web-farm) directly pkt will be redirected to indexing  server. But they said it will be L7 redirection. Not LB/Network level. 

View 5 Replies View Related

Cisco Switching/Routing :: 2911 / 2960 - Putting ASA On Edge

Dec 29, 2011

Today I'm going to be re-organzing my network, kind of and I just wanted to get a second opinon. Right now I have an ASA 5510 and a Cisco 2911 and a Cisco 2960 (and I have two more 2911s and 2960s that handles our phone network).
 
Router 2911 is on the edge Gi0/0 has the public IP and Gi0/1 is not used and then I have 5 individual VLANs (Gi0/1.100, 1.200, 1.300, 1.400, 1.500) VLAN 100 is our internal network 10.10.18.1/24 (router is 10.10.18.1)And the 2960 is used for swichport access, the ASA is on the side and only used as a VPN.
 
What I want to do is put the ASA on the edge so I can dump all the access-lists and everything then 2911 will only be used to route the traffic. Now I know I will have to reconfigure the VPN, which isn't a problem. My question is when putting the ASA on the edge do I just put the public IP on the ASA's e0/0 and then plug the 2911 into the e0/1 of the ASA and give the Gi0/0 of the 2911 the ip address of 10.10.18.1 or do I just shut it down? The reason behind this is because I would actually like to use the ASA for more than just the VPN passthrough.

View 6 Replies View Related

Cisco Switching/Routing :: Catalyst 2950G - Putting Fa0/2 In Error-disable State

Mar 28, 2012

I have a Catalyst 2950G when I activate the switchport port-security, but I want to empty the black list of mac address because every time I connect a device, the port is automatically désacative, here is the port configuration:

!
interface FastEthernet0 / 2
  switchport access vlan 17
  switchport mode access
  switchport voice vlan 51

[code]....

I tried the following commands to clear the blacklist mac address of that port, but the problem is still relevant:

# Clear mac-address-table dynamic int fa0 / 2
# clear port-security all int fastethernet 0/2
# clear errdisable interface fa0 / 2 vlan

View 17 Replies View Related

Cisco Switching/Routing :: WS-C3750X-12S-S Options To Achieve Putting All 4 Switches Into Single Stack

Feb 12, 2012

I have a couple of WS-C3750X-48T-L and a couple of WS-C3750X-12S-S, I want to stack all four of them together into a single stack. WS- C3750X-12S-S are running c3750e-universalk9-mz.122-58.SE2 whereas WS-C3750X-48T-L are running c3750e-universalk9-mz.122-55.SE3.I have got a couple of queries as under:What are the options to achieve putting all these 4 switches into a single stack? Can the LAN Base switches upgraded to IP Base?

View 3 Replies View Related

Cisco Switching/Routing :: Putting PoE Line Cards Into An Existing 4506 (older Version)?

Jan 13, 2012

I have a number of existing 4506 chassis type switches (the older non -E version) that I would like to roll out IP phones to. Instead of replacing the entire chassis, I would like to just replace the line cards in the switches with WS-X4548-GB-RJ45V. What or how much power supplies should I have in each switch to be able to power the 5 poe line cards (each port per line card will power an ip phone)?

View 6 Replies View Related

192.168.1.1 - Can't See Wireless Router Signal

Feb 23, 2013

I am trying to use a pre-existing DSL modem-router config in a club house my group uses for monthly meetings. It�s a separate modem and router (Linksys or Netgear), forget modem brand. I'm unable to communicate with the owners of the equipment. If I connect to the router directly with a cat5 patch cord I can get on the internet just fine, but do not see a wireless signal from the router. I am also unable to connect with 192.168.1.1 from my laptop. I get the same message as if I'd entered a random nonsense url. I know you can go into your router and disable wireless but first you have to talk to it via 192.168.1.1 .

So I got clever and piggybacked another known good router into one of the Ethernet ports on the 1st router, and again got on the internet with a direct cat5 connection. But this time, I DO SEE the wireless signal from my 2nd router and can connect to it from the laptop, but still no internet! it's like internet access is blocked in the 1st router.

View 11 Replies View Related

Linksys Wireless Router :: Use WRT54G Router With The Newer WRT310N To Extend Signal?

Aug 27, 2008

Can you use your WRT54G router with the newer WRT310N router to extend your wireless signal? How?

View 7 Replies View Related

Linksys Wireless Router :: E4200 Keep Connected To 5ghz Signal / Router Doesn't Respond To It

Jul 10, 2011

U just bought a new E4200 router to enjoy 5ghz band for the first time.I noticed the range at my house of the 5gh is smaller than 2.4 is that right?one of my pc is having trouble keep connected to the 5ghz signal or the router doenst respond to it, is there a way to improve that signal?

View 2 Replies View Related

Connecting A Router To A Wireless Signal?

Jun 5, 2012

I have access to and permission to use a wifi signal.I want to connect a router to it so i can connect a microcell via ethernet cable and enhance the wifi signal for my daughters ipods whats the cheapest way to accomplish this?

View 1 Replies View Related

Boost The Signal Of A Wireless Router Using Another?

Jan 24, 2013

boost the signal of a wireless router using another wireless router what I mean is that am receiving wireless signal but it is weak can I use another wireless router in my place to boost the signal>

View 11 Replies View Related

Ethernet Signal From Wireless Router?

Aug 18, 2011

I have an older desktop computer that I am trying to set up in my detached garage.It is only ethernet compatable. I have a wireless network in my house that my laptop is wirelessly connected to. I purchased a Linksys WET11 v2 wireless bridge. It is my understanding that this bridge will take the wireless signal and convert it to wired, but it is not working. When the bridge is connected to the old desktop, my LAN is active but I can't connect to the internet.

View 1 Replies View Related

TP Link Router Not Broadcasting A Wireless Signal?

Mar 14, 2013

I'm using Windows 7 with a TP Link router and an RCA cable modem. I only have a laptop and I had it set up so I had wireless on it, and was able to get wireless on my smartphone as well. All of a sudden the wireless stopped working and now I can only connect to the internet with the router plugged in to my laptop. I just updated my wireless driver and have tried the 192.168.0.1 thing so many times and nothing seems to work. I also exchanged my router for a new one and that worked for about a week and then stopped working again. This happened once before and it didn't work for a couple days and then I woke up one morning and it worked again.

View 14 Replies View Related

WNR1000V3 Router - Wireless Signal Dropping?

Jan 12, 2012

I have a Dell Studio 1745 Laptop and its only a few years old, I recently upgraded my router to be wireless a year or so ago and have had a few d/c issues here and there but mostly has not been a problem.Recently I have had tons of d/c issues while playing warcraft or browsing the internet in general, anything really.So I made the mistake of recently updating my WNR1000V3 router's firmware from my laptop's wireless connection. After I did this I saw all sorts of warnings (none built into the firmware itself, sigh) that this was a big no no.

Since then my d/c issues have been horrible but what it does now is my connection will be completely normal then all of a sudden my wireless access point will switch to 'No Internet Access' and it will drop my internet.The only way I can get it back is to go into the other room and reset the router by either unplugging it, or pressing the reset button on the back, once it reboots and everything, my laptop sees the connection again, and it has Internet Access fine.Soo I went and made the problem much worse, the lame part of the situation is before I had this firmware issue I was getting this problem anyways.

I decided if I could flash a older version of firmware to the router using my desktop that is wired to the router I could then reupdate it to the current version,I found a old firmware version on netgear.com and went to upload it through the router login for my router, it then said the file format was unrecognizable or not the right one (it was a .img file). I even tried to mount the file and explore it, no go. I found another firmware version older than that and attempted to flash that to the router and it began to update, then gave me a warning that this firmware was older than my current, I click yes and my internet drops and the update never happens.

So if I did screw the modem up this way I have no idea how to fix it now I have reset it to factory settings but this doesn't affect the firmware version. I suspect the firmware has something to do with the recent problems because I have seen the 'Congratulations, You have setup your router and are connected to the internet" like 20 times these past 48 hrs.I downloaded Xirrus wifi inspector and have it running now.I tried the ip flush and release stuff, and a bunch of tricks ive seen on other forums.My system is Windows 7 with a Intel wi-fi link 5100 AGN network adapter. I have tried rolling back that network driver and messing with the advanced and tcp/ip settings.

View 14 Replies View Related

Test A Wireless Router Signal Strength?

Dec 28, 2011

Any way to test a wireless router signal strength?

View 2 Replies View Related

Wireless Router - Low Signal Strength Outside Home

May 12, 2012

My router has wireless capability and the signal inside my home is pretty strong so I have no compaints there. The problem comes in when I use my computer which is located in a shed outside. I get a signal maybe 35% of the time, and even then it's weak. I want to use an access point to allow the computer in the shed to aquire internet access. Do I need to hardwire the access point or can I do it wirelessly? Would a repeater be more effective and which config would be best in that case?

View 2 Replies View Related

Boost Signal Strength On Wireless Router?

Jul 20, 2011

I'm trying to increase signal strength on my netgear router for my house.

View 4 Replies View Related

Linksys Wireless Router :: E3000 Cannot Keep Signal

Aug 21, 2011

We have  a wireless internet service. Not satellite. We basically have an antenna on our house that picks up the signal from a tower a mile or two away. I used the e3000 router when we lived in town with broadband internet and it worked fine. I can't get it to keep a hold of a signal. I can connect to the router from the computers but the router drops the signal from the tower. I have an old router that the wireless company was kind enough to lend me that works  , but the signal is weak and it could die at any moment... I"m at my wits end.. I have an expensive piece of equipment that wont hold the signal. I have updated the firmware and the Cisco connect software..

View 5 Replies View Related

Linksys Wireless Router :: Wrt160n - No Wireless Signal On 2nd Router In Cascade?

Dec 26, 2012

I have  a wrt160n as my main router cascading to an e1200 at the other end of my house. The idea was to enhance the wireless signal there. Went thru extended discussion with Cisco support settnig the system up.
 
Ip address of e1200 is set more than 5 apart from primary router, dhcp is disabled. The connection bewtween routers is Wan to Wan.
 
I have wired signal at the e1200 but no wireless signal?

View 2 Replies View Related

Linksys Wrt54g Router - Inconsistent Wireless Signal?

Jun 6, 2012

I have a linksys wrt54g wireless router and a few weeks ago my wireless connection started to become inconsistent, it would randomly drop service or be very slow, and now it has become very inconsistent and slow, all the while the wireless signal would be 4-5 bars.On my windows 7 desktop, often times the yellow triangle with the exclamation mark pops up over the signal strength indicator when its at 4-5 bars.I've tried changing to 2 different routers and its the same, and the problem is persistent for all computers in the house.I've connected directly via ethernet to the modem and router and service was fine.There are a few wireless networks in the area,some with quite strong signals, but I downloaded the xirrus wifi inspector and it says I'm not sharing a channel (channel 1) and though I'm ~15ft from the router, the signal is ~65dbm, which seems low and is almost equivalent to neighbor's wireless strength.

View 2 Replies View Related

Weak Wireless Signal - Connecting Second Identical Router?

Dec 20, 2011

My wireless network signal is great on the first floor, but is weak on the second floor. I have tried different antennas and various locations for the antennas, but with little improvement. I prefer not to purchase signal amplifier. I have a second identical router. Can it be connected to the current router (LAN output) and by way of a cat5 cable, placed on the second floor to boost the second floor wireless signal?

View 8 Replies View Related

Netflix Streaming - Low Wireless Router Signal Strength?

Mar 31, 2012

I have a wireless network in my home, mainly for internet access via any of the 3 or 4 machines we may be using. Normally, there's not a problem with normal surfing, email checking, youtube, etc.My wireless router is a Linksys WRT300N, and the wireless adapter card in my desktop is a D-Link AirPlus G DWL-G510 Wireless PCI Adapter. In my previous home, the router was in the very same room as my desktop, and had no problems to speak of with this setup streaming Netflix. Now, however, I'm set up in an older home, and the router is removed from my desktop by a few walls and tight rooms. I've noticed that my network status icon on the bottom right of my desktop seems to always show "Signal Strength: Very Low".I like to use my desktop sometimes to stream Netflix. My Netflix streaming sometimes goes OK, but typically it just freezes and shows the Loading bar, and sometimes doesn't really start back. It is so bad sometimes, that I am not willing to wait it out, because I know from this experience that even if it starts back up, it will just freeze again. The video is not downloading and caching fast enough.

View 5 Replies View Related

Linksys Wireless Router :: E2500 Low Signal On 5Ghz

Feb 20, 2012

I am using the E2500 with the Wireless N-pci adapter with dual band, both with the latest drivers / firmware, and I am getting extremely low signal quality and connection speed when connecting to the 5 Ghz network.My computer is no more than 15 feet away from the router, and on the same level. I also verified the connection with the 2.4 Ghz band, and it reads as excellent, and with 54 mps. Using 5 Ghz I get one bar of signal quality (very poor) and no more than 13 mps connection speed.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved