Linksys Router Does Not Seem To Putting Out Signal
Jan 12, 2011The laptops that normally run from the Linksys network are not showing any network at all. The "Easy Link Advisor" says the network is working.
View 2 Replies
ADVERTISEMENT
Wireless Router Is Not Putting Out A Signal?
Nov 7, 2011I have a Dell Wireless Router, yes I know terrible lmao but was free a laptop I bought my sister. Anyways, it does not seem to be putting out a wireless signal.However if hook an ethernet cord from the modem, to my parents pc, eliminating the router completely, the internet works, this is how the set up usually is. I have my pc upstairs with a wireless card and have never had problems until now.When I hook up the wireless router, the internet light, lights up etc. But on the main computer that is hardwired, loses internet. It just has "Limited Connectivity".I tried resetting, powering off, restarting. I tried to set up a new wireless network and the computer cannot find any wireless devices. My computer upstairs cannot find a wireless network either.We also have a wireless "Roku" box which is netflix, this works off wi-fi, but this also cannot get a wireless connection.
Ive tried typing in the routers ip just guession that is the 192.168.1.1, I have tried a bunch of others but cannot get into my routers settings. I am trying to get into those router settings thru my browser, Im trying to figure out the ip. However if I hook my router up I lose internet so i am un-able to do that.I build PC's and service them, but networking is where my expertise end.
How To Restrict Router By Putting In Password
Jan 9, 2011How to restrict my Router by putting in a Pass word so my neighbours could be stopped using my highspeed internet and thus makinit weaker for my household.
View 3 Replies View RelatedCisco WAN :: NAT / Access After Putting 5512 ASA Behind RV180 Router
Feb 12, 2013Previously we had a 5512 ASA setup and working properly. We had several internal address static nat'd to external address and were able to access our servers externally. Unfortunatley, when it came time to setup our site to site vpn we found out our ISP was blocking the necessary traffic on the IP we were using for the ASA's outside interface. We ended up having to buy a RV180 to act as a dummy router to assign the restricted IP to on its outside interface and put the ASA behind it so we could assign it an unrestricted IP for it's outside interface for the site to site vpn.
The problem is our NAT and access rules are no longer working. Internet access works fine however. We haven't even set the site to site vpn stuff up yet either. What do we need to change in either the ASA or the router to get this working again. I don't even know where to begin with providing any pertinent information for diagnosing the problem.
Linksys Wireless Router :: Use WRT54G Router With The Newer WRT310N To Extend Signal?
Aug 27, 2008Can you use your WRT54G router with the newer WRT310N router to extend your wireless signal? How?
View 7 Replies View RelatedUse A Linksys WRT54G Router To Get A Signal For Desktop?
Aug 6, 2012Can I use a Linksys WRT54G router to get a signal for my desktop? I am using a modem that has wifi downstairs and want to get a signal for a desktop I have in the kids room upstairs
View 4 Replies View RelatedLinksys Wireless Router :: E3000 Cannot Keep Signal
Aug 21, 2011We have a wireless internet service. Not satellite. We basically have an antenna on our house that picks up the signal from a tower a mile or two away. I used the e3000 router when we lived in town with broadband internet and it worked fine. I can't get it to keep a hold of a signal. I can connect to the router from the computers but the router drops the signal from the tower. I have an old router that the wireless company was kind enough to lend me that works , but the signal is weak and it could die at any moment... I"m at my wits end.. I have an expensive piece of equipment that wont hold the signal. I have updated the firmware and the Cisco connect software..
View 5 Replies View RelatedLinksys Wireless Router :: E4200 Keep Connected To 5ghz Signal / Router Doesn't Respond To It
Jul 10, 2011U just bought a new E4200 router to enjoy 5ghz band for the first time.I noticed the range at my house of the 5gh is smaller than 2.4 is that right?one of my pc is having trouble keep connected to the 5ghz signal or the router doenst respond to it, is there a way to improve that signal?
View 2 Replies View RelatedLinksys WRT54G2 / 4th Router But Still Dropping Signal To Laptop?
Feb 14, 2011i am on my 4th router but still dropping signal to laptop. if I unplug the router and plug back in it works. but not for long. am getting very upset.
View 3 Replies View RelatedLinksys Wrt54g Router - Inconsistent Wireless Signal?
Jun 6, 2012I have a linksys wrt54g wireless router and a few weeks ago my wireless connection started to become inconsistent, it would randomly drop service or be very slow, and now it has become very inconsistent and slow, all the while the wireless signal would be 4-5 bars.On my windows 7 desktop, often times the yellow triangle with the exclamation mark pops up over the signal strength indicator when its at 4-5 bars.I've tried changing to 2 different routers and its the same, and the problem is persistent for all computers in the house.I've connected directly via ethernet to the modem and router and service was fine.There are a few wireless networks in the area,some with quite strong signals, but I downloaded the xirrus wifi inspector and it says I'm not sharing a channel (channel 1) and though I'm ~15ft from the router, the signal is ~65dbm, which seems low and is almost equivalent to neighbor's wireless strength.
View 2 Replies View RelatedThe Signal Strength Is Excellent But Not Getting Internet (linksys Router)
Mar 12, 2012I have a linksys router,I reset it and hooked it up,but I don't get internet even though the signal is excellent
View 1 Replies View RelatedLinksys Wireless Router :: E2500 Low Signal On 5Ghz
Feb 20, 2012I am using the E2500 with the Wireless N-pci adapter with dual band, both with the latest drivers / firmware, and I am getting extremely low signal quality and connection speed when connecting to the 5 Ghz network.My computer is no more than 15 feet away from the router, and on the same level. I also verified the connection with the 2.4 Ghz band, and it reads as excellent, and with 54 mps. Using 5 Ghz I get one bar of signal quality (very poor) and no more than 13 mps connection speed.
View 9 Replies View RelatedLinksys Wireless Router :: Low Signal Strength With Wrt54g?
Oct 16, 2011My wireless router has been spotty since my cable company installed a new modem for cable internet. I have powercycled several times, downloaded new firmware, rebooted and am still having problems. Lately when I do finally get on the internet with a wireless device, the signal strength is very low. It is low on my iphone, on my Mac laptop and also on my Samsung Bluray player. Lately a window keeps popping up when I am trying to watch netflix that states my band width is too low, even though it has been working fine for 2 months. Is my router outdated?
View 5 Replies View RelatedLinksys Wireless Router :: E4200 - Signal Is Much Weaker?
Dec 30, 2009Just got the E4200 and it seemed great at first. Connected at 450mbps at close range (maybe 6ft away) and got 223mbps transfer.It seems that recently my signal is much weaker. I'm around 6-8ft away from the router and I'm getting between 270-360mbps, which to me is poor given the short range.
InSSIDer says the RSSI is -50, while my other wireless N router (dual band) is -35 and is in the exact same location. I'm using the 5ghz radio only, and it is set to N, and I'm using channels 44 and 48. I checked the hidden advanced wireless page and transmit power is already set to high.
My laptop has an Intel 6300 wireless card.I'm using the current firmware 1.0.02. I've noticed that the speed of the router randomly seems to drop off too (just as I type this, the link rate has gone back up to 450mbps... typical). Is the router throttling when it gets hot or something? So I just want to find out if others are experiencing similar rates at the same kind of distance. Seriously, how can you advertise something as 450mbps when you can't even get that link rate at a distance as short as 6ft?
I can't see any thing I can do to increase the link speed (back down to 270mbps now), short of a firmware update to increase the power and use higher channels. I hear the higher channels are much better, so who do I have to write to, to plead for new firmware?This is a great product, but it's totally ruined by stupid internal antennas and a weak transmit power. Maybe if we make a noise about the not so maximum performance, they might address it.
Linksys Wireless Router :: Use Two E1000s To Increase Signal
May 8, 2012I have an E1000 router in my office with a cat5 cable going to my daughters bedroon thru several doors and around some corners. She (recently moved back in) has an E1000 router also.I need to know how to use both routers to increase the wireless signal in her bedroom.I have not tried anything yet.The router in my office is configured with an address of 192.168.2.1.
View 7 Replies View RelatedLinksys Wireless Router :: E2000 Get One Bar Signal Downstairs
Jul 5, 2011I just moved into a 4200 sq ft home that was built in 1900. I have a Linksys e2000 and I have it upstairs and it only covers the upstairs. I get one bar signal downstairs. I was wondering if I should buy a wireless repeater (if so which one) or upgrade to a better Linksys router (e4200).
View 5 Replies View RelatedLinksys Wireless Router :: Wrt54gx4 Not Being Used - Signal Won't Reach
Jul 3, 2011I have DSL set up in a home network. I want it to be used in my barn. The signal won't reach wireless though. I have 2 older wireless routers not being used - Lynksys wrt54gx4. Can I add two of these in the path to the barn to extend the signal? I would put one in the back of the house and one halfway to the barn in the pool house. ZCan these routers connect wirelessly to the home network?
View 3 Replies View RelatedLinksys Wireless Router :: WRT310N Emits No Signal At All?
Sep 26, 2012I have a WRT310N router. I called the connection "Monica". Well... Monica doesn´t appear in my web and connection center. It simply doesn't exist any more, as if it was off, but it is on, all the lights are on. I checked de internet supply and it works. I don't know what to do..
View 1 Replies View RelatedLinksys Wireless Router :: How Far Should Signal Of E4200 Stretch
Feb 4, 2011How far should the signal of the E4200 stretch? I am noticing some serious issues with signal strength on the far side of my house. I was under the impression that the E4200 was able to stretch much further distances than most N routers. Is there a setting i can adjust to increase the range?
View 9 Replies View RelatedLinksys Wireless Router :: Disable Wi-Fi Signal On EA4200?
Nov 19, 2012I am trying to use my EA4200 wireless as simply a router to run my home network. I want to leave all my cables plugged into it and distribute the internet via the switch to my other computers. I just want to turn of the wireless feature.
View 2 Replies View RelatedLinksys Wireless Router :: E2500 - Signal Dropping
Mar 28, 2012I just bought and set up an E2500 wireless router this evening. Using the default settings (as applied by the Cisco setup CD), I was experiencing pitiful range, with signal dropping to 2 out of 4 bars just one room (about 20 feet away). (Previously, using the exact same physical setup with the same computer and a single-band Belkin n150 router, I always had 4 out of 4 bars in that room).
I entered an online live tech chat, and after some back and forth, the tech rep had me change the settings as follows:
(1) Rename the SSID to separate the two bands: One network SSID for the 5GHz band, another for the 2.4GHz.
(2) Turn off auto-channel for both networks: Set 5GHz to stay on channel 36. Set 2.4GHz to stay on channel 1.
(3) The 5GHz is set to use 20/40 MHz width, while the 2.4GHz is set to use only 20MHz width, but I believe those were the defaults already in place.
Then he promptly ended the chat, so we didn't get to finish. Nonetheless, with these settings in place, I am now getting a steady, uninterrupted 4 bars in the next room, using the 5GHz network SSID. Because we were disconnected, I have a few questions remaining:
(1) Is it normal to get such terrible range using the default settings (that's make for a lot of unhappy customers and a lot of extra calls to tech support)? Or does this indicate a problem with my router? (This was a Cisco certified refurbished model)
(2) Which change 'fixed' the problem: Was it separating the two bands into different SSIDs, or locking the channels rather than using Auto channel?
(3) Was this just intended as a test to troubleshoot the problem, or am I supposed to leave the router configured this way? (Since we were disconnected, I didn't get to follow up with the tech rep after changing the settings.) With it configured this way, I'm connecting devices that can find the 5GHz network to the 5GHz network's SSID, and the other devices that can't find it, I'm connecting to the separate SSID for the 2.4GHz network. Seems unnecessarily messy to have 2 SSIDs.
Putting Speed Caps On A Network?
Mar 14, 2011I am an administrator and my co-worker keeps on going on you tube during work. Is there any way to make his computer only use up 20KB per second instead of 150 KB per second?
View 6 Replies View RelatedLinksys Wireless Router :: E1000 Weak Wifi Signal
Jul 20, 2011Got a new e1000 after a RMA. The new unit has a very weak wifi signal. I've tried all different channels. It is running in mixed mode. No microwave, blue-tooth or other noise. 4 feet from the router and the signal is down to -90db. Take a few more steps away and the connection is lost.
View 2 Replies View RelatedLinksys Wireless Router :: E1500 - Way To Disable Guest Signal
Nov 18, 2011Just bought an E1500 wireless router -- when setting the router name and password, a 2nd guest sight came up, but I had to leave the computer, and when I came back that page was not there. I do have a guess password, that is fine---what I want to remove is the guest signal to our Dish Network wireless sight.
View 2 Replies View RelatedLinksys Wireless Router :: EA6500 - Setup Could Not Find Signal?
Feb 2, 2013In first setup, error meaasge " we could not find your router :setup could not find your router's wireless signal ..." i checked cable and internet signal. i find one problem : the light of internet port of router is not blinking.i reset my router but problem is not solved.
View 5 Replies View RelatedLinksys Wireless Router :: How To Boost Signal Range Of WRT310N
Aug 20, 2008How to successfully increas the signal range of the WRT310n? I live in a huge old place and the signal drops to one bar (dial-up speed) about 40 feet across the building. However, at the room before that (maybe 30 feet) my Apple Mac book gets great signal and it's no problem. I need to connect the Mac and 2 PC laptops wirelessly.I'm not sure whether to try a signal booster, set up another access point (or how to do that anyway), or what? Running a cable is unfortunately not an option.I also have a WRT300n (which was replaced this weekend with the 310n). Not sure which one really is better, but the 300n router's range didn't even make it as far as the 310n does. (There was weak signal, no active bars.) Someone suggested adding a more powerful antenna to that router instead?
View 3 Replies View RelatedLinksys Wireless Router :: EA4500 Speed Quality And Signal
May 27, 2012Bought the new EA4500 a couple of days ago and have looked at my wireless connection and see it varies from 72Mbps to 144Mbps. It has jumped up to 270Mbps a few times, but rarely. Shouldn't it be 300Mbps most of the time? My laptop is 4 feet away from the router and the router is on top of a card board box being elevated away from interference. The prior router was a dlink 855 that went whacky after 3 years. I believe I was usually at 270 Mbps with that. What gives? Do I have a faulty router? With this new router, I expected the range to be a lot farther and faster too, but it is not in my family room. 2nd floor router, family room is 1st floor about 50 feet away and I get 1Mbps - 5Mbps. Everything is set to Auto on router and IP6 is disabled on laptop.
View 9 Replies View RelatedLinksys Wireless Router :: Can E3000 Be Used To Boost Wifi Signal
Nov 24, 2012I have Att internet services and the modem I received from them has WiFi with it. The signal that it produces is very weak. I was curious if there is any way to use my E3000 to boost or repeat the signal so WiFi will extend through out the house.
View 4 Replies View RelatedLinksys Wireless Router :: Set Up Two E4200 To Improve Signal Strength?
Sep 24, 2012Currently I'm using one e4200 (v1) as my main router in the house. The wireless coverage downstairs is perfect, but upstairs the signal is weak. To improve this I thought about adding the WAP610N as an access point to my network. But this device gets quite some negative reviews ... Thus I was thinking why not add another e4200 (v2) to my network? The price difference is not that big, especially compared to other simultaneous dual band access points. So my question is, would following scenario work?
- first e4200, connected to my ISP, acting as a router, using both the 2.4 as 5 ghz band (basically my current situation)
- second e4200, connected (via UTP cable) to the first e4200, in bridge mode
- second e4200 also using both 2.4 and 5 ghz band, using the same SSID, security etc but a different channel
So when moving a laptop for example from downstairs to upstairs, automatically the router/access point with the strongest signal would be used.
Linksys Wireless Router :: E2500 Constantly Dropping Signal
Jun 20, 2012My E2500 Linksys has never been consistant with its signal to my MacBook Pro.
View 8 Replies View RelatedLinksys Wireless Router :: E1000 - How To Increase Signal Strength
Nov 29, 2010We have a new e1000 router that was having trouble reaching the TV for Netflix movie streaming. Too many walls and too much distance. A simple solution was to direct the signals from the router by placing aluminum foil behind the router so all the signal was going towards the TV rather than in an 360 degree circle. Now the streaming works great! After the movie is done I remove the foil and everything looks just like it should.
View 9 Replies View RelatedLinksys Wireless Router :: WRT120N Drops Signal To Laptop?
Sep 17, 2011My WRT120N drops signal to Laptop occasionally and I do not understand why. I tried to update the firmware, version 1.0 to 1.0.04, is that a newer version? My next step is to try to update the drivers in the laptop. The dropped signal seems random and only happens with the laptop. Other devices connected work fine.
View 2 Replies View RelatedLinksys Wireless Router :: WRT54G - Signal Won't Reach Laptop From Far Away
Mar 25, 2013it might be good to point out first that this was never a problem before i began fixing a completely irrelevant problem (screen broke) with my laptop, which took around three weeks. i could at that time use the internet a couple of rooms away from the router just fine, but now it's a no-go. .
the model is WRT54G, and the serial number is CDFD1F9CJ507.