My 7 inch netbook authenticates to a wifi network with short network key but cannot authenticate to one with a very long key. I am using Win CE 6. The encryption method is AES, the authentication method is WPA-PSK. The short password key is 9 digits consisting only of numbers and letters. The long key consists of 35 digits, with spaces, capital letters, numbers and an exclamation mark.
View 2 RepliesI have a dell inspiron mini 1010 with 1397 wifi card. I am trying to connect to internet through wifi but comp. wont connect. when i run diagnostic it says internet ip ping faild. my router( witch is an arris xfinity) is working fine with two other computers. strangly it connects with my netgear router just fine.
View 1 Replies View RelatedI use IE7.0
192.168.1.1
user name : admin
password : admin
Error is saying "401 Authorization required" Browser not authentication-capable or authentication failed.
I've just purchased a second hand laptop for my Hubby and trying to gain access to the internet through my SKY wifi router. It keeps saying its within range but this error of Wireless authentication failed because of timeout!
View 5 Replies View Relatedpicking up on old thread, but same issue: authentification failed because of a timeout
*previously*! i was able to auto connect fine on this home network via wifi.the line and box recently changed, same provider, and now i'm the only one who can't connect.the SSID changed, but i've done all the usual routines, deleting and re-adding manually, etc. but nothing so far...
i *don't* think this is a case of changing gear, but i don't know enough about internet/connection/configuration to fix this. yet!
NB: when i perform the reset on the box as instructed, using the provider's setup software - i am not the account holder - for the wifi, it shows connected very briefly in the animation, and then goes off again; this is the authentification/verification failing, i conclude.
so: with what is said above, i'm wondering if my antivir is to blame, or the windows firewall settings.or malwarebytes.i'm going to study the info i've got off my system, and looking at the router via the http routine, offline, as i now have to get off the internet(...); i'll get the infos together so i can post something useful.
I realize there are a few other threads on this subject. Ive followed some of the advice and I still can not connect. I am currently connected via Ethernet cable but I cannot connect to wireless. I have removed all the stored networks. My event log states: [code]....
View 5 Replies View RelatedI'm trying to set up my DIR-835. I keep getting "Authentication failed".
View 4 Replies View RelatedWhen I try to log-in to my D-Link DIR-835 Router using IE9, I get an 'Authentication Failed' error. FireFox & Chrome work just fine. what I need to change or fix in IE9 so it will also log-in to my router?
View 13 Replies View RelatedI got a report from a branch office which is getting trouble to authenticate users to the WLAN this is a stand alone AP which has a configuration script that we use for all our branch offices but in this case is not working. It seems to be an issue with RADIUS but if it was the case the whole company would be experiencing problems since it is a central RADIUS server.
Here is a log from the AP By the way I modified the radius server timeout to 90 sec
APIMMEXP01#
Sep 1 17:01:47.240: %DOT11-7-AUTH_FAILED: Station 0021.5c7f.1739 Authentication
failed
Sep 1 17:01:53.503: %DOT11-7-AUTH_FAILED: Station 0026.c64b.c3d6 Authentication
failed
Sep 1 17:01:58.739: %DOT11-7-AUTH_FAILED: Station 001e.65cf.9ca8 Authentication
failed
[code]....
I have a guest network and lately I have been experiencing troubles with some users.The symptom, as I create a username and password and type'em in a laptop the authentication fields in the web authentication page don't keep the data as if I didn't type anything
WLC 4402-50
Version 7.0.98.210
I have have a XPS L502X. I decided to make a clean installation based on Windows 7 Ultimate.My problem is when I instal the driver for the "Dell Wireless HSPA 5540" it fails with then warning:
"Authentication failed. The .... driver cannot be installed on this computer...."
How to install driver for this ?
I'm trying to connect to ISP with PPPoE method using Cisco 861 equip. On the other side Cisco 3845 BRAS.Session fails at authentication phase. Authentication protocol chosen by routers is ms-chap-v2. Chap supported also. [code]
View 2 Replies View RelatedI have already set up a lab comprising of 1x2950-24 switch, 2x3750-24T in stack mode and 2x MS Domain Controller with AD 2008 Servers and NPS enabled (Domain level 2008). I use NPS as a Radius Server. I am trying to test the 802.1x framework in two scenarios.
1. I use as client a domain laptop with Windows XP SP3 with the embedded 802.1x MS supplicant. As authenticator use the 2950 switch and as authentication servers I use the two NPS integrated in MS DCs. Everything is working fine as I expected with basic configuration guidelines from Cisco & Microsoft.
2. I use as client a domain laptop with Windows XP SP3 with the embedded 802.1x MS supplicant (the same as before). As authenticator I use the 3750 Stack switch and as authentication servers I use the two NPS integrated in MS DCs (the same as before). I have configured the supplicant for both machine or user authentication in both scenarios. However the client never pass the authentication in the second one. I disconnect and connect the same supplicant in the 2950 switch and the authentication is completed successfully. Getting back to the 3750 stack the authentication failed and the laptop gains network access in the configured Auth-Failed Vlan. I have tried several configuration changes without success. I cannot understand why does this happen. I have made some debugs and I am sending them a long with a partial basic configuration of 3750 stack switch.
We have a C4948E switch which is generating the following logs every ten minutes:
May 28 12:44:13 UTC: %SEC_LOGIN-4-LOGIN_FAILED: Login failed [user: Username: -40.0] [Source: 0.0.0.0] [localport: 0] [Reason: Login Authentication Failed] at 12:44:13 UTC Tue May 28 2013
May 28 12:44:59 UTC: %SEC_LOGIN-4-LOGIN_FAILED: Login failed [user: ] [Source: 0.0.0.0] [localport: 0] [Reason: Login Authentication Failed] at 12:44:59 UTC Tue May 28 2013
We have a terminal server (C2901) set up with reverse ssh to all the devices including the above C4948E. Can this be the one to initiate the logins?
The IOS of both devices is as below:
C4948E - cat4500e-entservicesk9-mz.151-1.SG.bin
C2901 - c2900-universalk9-mz.SPA.152-3.T.bin
I am unable to identify what is triggering the above logs to be created.
We have ASA 5520 as SSL VPN concentrator so users can access internal web from outside. Our internal web also has several internet URL. What we want is when user click internet URL in our internal web, ASA forward those request to internal proxy server. I already config proxy using port 8080 and username "companyuser" and password, but always have authentication failed on ssl vpn browser. We uses forefront TMG as proxy. Username and password have right to access Internet.
View 2 Replies View Relatedwe have a ACS server V4 installed on W2003 server ,when we make a telnet to an equipement on the wan the authentication pass on the first connexion ,but when we telent to a switch on the lan the first connxion fails and we need to retry to login .when i check the field attempt log on the ACS i dont find the field attempt.i find this issue in ALL switch on the LAN ,from the switch i can ping the the ACS server .this problem appear frequently?
View 1 Replies View RelatedI have a little problem with my ASA 5510 version 8.2(1) with a IAS server RADIUS for strong authentication.
I have configured a double authentication for my client to access SSL portal:
First authentication: AD serverSecondary authentication: IAS for my token SAFENET ALADDIN The server IAS is declared on a W2K3 and it's standard.
The problem I have is that after more than 24hours of unutilization, when i try to log in, my authentication failed the first time and then the other tries work fine as long as I use it in a period of 24hours.
I first thought about the timeout so i tried to put a "timeout" of 15seconds for AD and IAS servers and a "retry intervall" of 3 seconds, it doesn't change much.
Is there a tool/option in the ASA to check connectivity with the radius every 1h for example.
Having an issue where a user will plug a PC into a switch. The switch does a MAB authenticaiton and the MAC is not located in the ACS server. It logs the failed attempt, but when the PC is removed from the switch, the failed attempts keep getting logged until the port is bounced. Any way to keep the attemps from happening after the PC is removed? If not, any way to make it stop without bouncing the port?
running ACS version 5.2.0.26
switch port config:
interface GigabitEthernet1/0/2
sw access vlan 2 sw mode access
authentication control-direction in
authenticaion host-mode multi-auth
authentication port-control auto
mab
spanning-tree portfast
I have configured Radius authentication on Windows 2008 server (NPS) The following configuration is working perfectly on Cisco Switch 3560. [code]But, the same configuration is not working on Cisco Catlyst Switch 6509 (C3560-IPBASEK9-M), Version 12.2(46)SE, RELEASE SOFTWARE (fc2)/
View 2 Replies View RelatedWhile the home PC and my brother's laptop can connect to the wireless internet, my sister's laptop has never been able to. The antivirus software installed is Avast! and there is also a Windows Defender. It can connect no problem using an ethernet cable.
View 3 Replies View RelatedI've been configured my device 6506-9 with TACACS+ server authentication: [code]
but when I tried to access the device only uses authentication local but not uses TACACs (with username/password defined) it can be an error in configuration? in the other devices of network this works properly, only it's wrong in Cat6506-E
I am trying to configure a Cisco 1042 autonomous AP and have ran into some problems. I require 2 broadcasted SSIDs that use WPA v2. When I only have 1 of the SSIDs enabled, I can authenticate with no problems. When I have both SSIDs enabled, I can connect to one of the networks, but not the other. I have verified the PSK multiple times, but the logs still show dot11-7-auth_failed. If I remove the working SSID and make no changes to the SSID for which authentication previously fails, everything works fine. Upon adding the other SSID back, I run into the same authentication issue.
View 3 Replies View Related I replaced an ACS certificate that had been installed as follows:
1. Generate CSR file and private key file, then send CSR to GeoTrust (Key length: 2048 and Digest to sign with SHA1)
2. GeoTrust send me a certificate. Issued by "GeoTrust SSL CA".
3. Install the certificate on the ACS. Restart ACS service.
4. ACS Certification authority setup. Issued by "VeriSign Class 2 Public Primary Certification Authority - G3"
5. Edit certificate trust list and select "VeriSign Class 2 Public Primary Certification Authority - G3" as trusted.
6. Enable EAP-TLS, then restarted the ACS service. The problem is when i try to enable EAP i get the error msg:Failed to initialize PEAP or EAP-TLS authentication protocol because CA certificate is not installed. Install the CA certificate using "ACS Certification Authority Setup" page.I searched on cisco and it said to disable the CSA, but in fact there is no CSA installed on this server.
OS: Win 2003 sp2Cisco ACS: Release 4.2(0) Build 124
The update "failed," due to an "unexpected error." Wireless connection is disabled, although, as you have probably noticed, I can still connect to the internet (using an ethernet cable from my router to my laptop OSX 10.6.8). Error Code 3018 is unknown to Cisco's website. Or should I just start over with the installation disk for my E4200 router?
View 2 Replies View RelatedI am actually able to have fun surfing on the Net with this toy computer, provided I don't expect to watch videos or listen to music or download anything. I bought it for a few Euros in France where it is known as the "SurfOne mini PC Ref. INOS1CE"; I think it is the same as the Chinese "OEM mini laptop netbook". It has a 7" screen, a 2 MB memory and claims to run on Windows CE 6.0.My problem is that after successfully connecting via WiFi to my "Orange Livebox" modem and router for a few days, I then lost that connection and can connect now only by cable.When I turn on WiFi power, it recognizes the "Livebox", but then states that it is not receiving any signal and the connection fails. How to restore WiFi.
View 1 Replies View Relatedi looked around and couldnt find a proper answer for me, i am trying to get wifi before i build my shuttle sz77r5 case, any mini pcie wifi card to use. Secondly does a mini pcie wifi NEED antennas to work (how come laptops which use these cards dont need antennas), as there are no holes for the connections in the back of the case for antennas.
View 6 Replies View Relatedhow to configure WiFi on laptop Sony mini in window 7
View 2 Replies View RelatedI am having Sony Ericson xperia x10 mini In my mobile wifi is activated and i'm able to browse now what my need is i would like to browse in my pc.
View 1 Replies View RelatedJust purchased an Asus K532-BBR9 laptop. Everything works fine, except on college campus the internet is very slow, and disconnects every few minutes.My fellow students laptops do not seem to have this problem.I figured it may be a driver issue, so I am trying to update everything.Under Network Adapters in Device Manager. The Microsoft Virtual WiFI Miniport Adapter is not up to date when I do a driver update scan.Then it says "Windows can't verify the publisher of this driver software.." with options to install anyways.
View 2 Replies View Relatedcan you use a Mini USB WiFi Wireless Adapter LAN Network Card on a desktop computer
View 4 Replies View RelatedThe original network had a Zylex router, Netgear Switch. There was 2 pc's, one XP and Win 7. There is also 3 tills connected too.There is VPN network connected too. This emits a wireless signal to connect to a scanning gun and is also used to administrate the entire network. I was told by the Administrator of that network that it shouldn't interfere with the wifi network.The job I was requested to do was to install 3 new wall plates as the Win 7 pc was using a Belkin wireless adapter. There was 2 put inside the office where the XP and Win7 pc's are located. The 3rd was just outside the office.Now all the ethernet connections work 100%. The wifi is another story though. It will show up in the connect too, when you try connect it will disappear/no response from AP/connect then disappear, these are random too. No order to when each is error is displayed. Even when I put in another router the exact same issues happen.I have tried to connect to both routers wifi when it wasn't plugged into the switch. Just the router's turned on with no cables plugged in separately of course, no joy same issue with both.
View 2 Replies View RelatedI have a Netgear N300 wireless router. My laptop is Sonay Viao, running Windows 7.
This morning my internet was unreliable, and dropping every minute or so. Trying to trouble shoot, I switched the router off then on again. Now I have no wireless signal between my laptop and router. The router doesn't seem to be recognising the security password. I have not changed the password - this is still the original password for the router. Other devices are still talking wirelessly to the router.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: Pentium(R) Dual-Core CPU E5300 @ 2.60GHz, Intel64 Family 6 Model 23 Stepping 10
Processor Count: 2
RAM: 6134 Mb
Graphics Card: Intel(R) G33/G31 Express Chipset Family, 256 Mb
Hard Drives: C: Total - 463782 MB, Free - 396406 MB; D: Total - 13154 MB, Free - 1850 MB;
Motherboard: PEGATRON CORPORATION, Benicia
Antivirus: McAfee Anti-Virus and Anti-Spyware, Updated and Enabled
I recently bought a Sony Bravia HD TV with wireless internet capabilities.When I try to connect to my wireless internet. The TV finds our wireless router name, but when we try to finally connect wirelessly it gives the following message: TV wi-fi found, local access failed and network access failed. The router we have is a Actiontech PK500.On the TV we have three differant ways for the tv to locate the router they are by scanning, the WPS button and by entering the WPS pin. We've tried all three and got the above message.