I have a linksys router connected to four computers and putting out a wireless signal. I also have a PC upstairs I would like to get online, and have a WRT54G V5 wireless router that I want to use like a wireless USB stick. Is this possible without downloading additional firmware beisdes official Linksys firmware?
View 6 RepliesI want connect an external HDD 320GB FAT32 2,5" but E4200 dont found it. USB Stick with 4GB is working.E4200 have latest Firmware.
View 1 Replies View RelatedI've been trying to re-purpose my E4200v1 as a Bridge, AP or some other thing that might work with wifi coverage in my home. I am using an Asus as the primary router. and I have Verizon Fios so I have a coax/ethernet router with its wireless switched off so that the Asus is primary. That works, but when I go to reset the E4200v1, I can get it to take a new IP address, but when I attempt to put it into bridge mode, as soon as I hit "save settings" I see the admin screen flash and it goes back to its origninal settings, instead of saving the new settings.
View 9 Replies View RelatedI'm trying to stream music files to my A/V system. After weeks of encountering problems, I discovered that UPnP was disabled (by default) on the router. After enabling UPnP on the router, bingo......it worked. My A/V system has a Yamaha A/V receiver, which is a networking receiver capable of net radio and accessing/playing files on my PC. Net radio works fine. The problem I'm having is that when I shut down the A/V receiver, turn it back on, I can't access the files. I have to disable UPnP, save changes, and then reenable UPnP, save changes. When I do that, all is well and my receiver "sees" my PC and files. Shut down the receiver, turn it back on, back to square one and have to do the do the disable/enable routine again. PC is WinXP, using Windows Media Player 11. Seems the "enable" UPnP desn't "stick", even though it shows enabled on the setup page.
View 6 Replies View RelatedI want to know if i can format or rerouter a Vodafone mobile broadband model: k3571-z to use as wireless reciever for a cable broadband in my house, no computer details as yet as im still in process of building one.
View 1 Replies View Relatedi would like to know if i can use my 3g stick connected to a computer to use it with my router to have wirelles signal in my house.
View 1 Replies View RelatedI try to make Nat on a stick, but not successful.
Network Diagram
Config File
interface Loopback0ip address 10.0.1.1 255.255.255.252ip nat outsideip virtual-reassembly!!
interface FastEthernet0!!interface FastEthernet1!!interface FastEthernet2!!interface FastEthernet3!!interface FastEthernet4ip address 60.160.60.138 255.255.255.248
[Code].....
we (educational institution)are attempting to trace an ip address for a STC USB stick. Actually, we have requested STC GSM provider to trace it. Reason being is, one or more of our teachers have sent an email harassing other staff. We wish to find out if STC has the techincal know how to get this info.
View 2 Replies View RelatedI purchased a Virgin Mobile Online Stick where you do not need a telephone jack, modem, router etc. or anything to go online, It's like, go online from everywhere, like at&t offers it too. Costs like 40-50 bucks a month.But I cannot go online. i insalled the stick and when open the icon, it connects and says ready, but I cannot reach ANY site at all.I saw in the network section that there is a little red x infront of the locale area connection and it always says, connect a cable. But this should not be the cae since you do not need any kind of cables with this stick.A friend of mine and I had the same stick from at&t and it worked perfect. We just double clicked the at&t icon on the desktop, clicked connect and everythng was great and we used it to 100% in the car missing or doing wrong?PS: PC runs on Vista AND, when calling Virgin, they just tell you, that's not there problem because it shows that it is connected, which is true, but still cant reach ANY website
View 1 Replies View RelatedI have been asked to setup a VPN on a stick setup so that people on the move can use the encryption of our SSL VPN for web browsing etc using Any Connect. This works fine, whats my ip shows the external IP of the office when connected to the VPN and all traffic is pushed down the pipe. The only issue is when connected I have no access to local resources such as IP printers etc. How to do this on 5505?
View 6 Replies View RelatedHow to unlock EC156 HSIA USB stick for work with GSM SIM?
View 1 Replies View RelatedIt doesn't seem like I can set up trunking (dot1q) on this device. Isn't it supported on this device? Can I still set up VLANs with the router-on-a-stick concept working internal in the device, i.e no external interfaces/subinterfaces being configured? If so, can I then connect VLANs to other switches? I have:
-876 ISR
-Catalyst 2960
-SLM2008
I know the small biz switch supports VLANs and I think trunking as well--obviously the 2960 supports it. Is there a way with these devices to configure one VLAN for servers/net devices and another for regular end-user computers so that they still talk to one another, or do I need a different router in the mix?
I tried to install Vodafone K3765 USB internet stick. I installed the software which came in the flashdrive. With this software I tried to connect to internet but I got error message "The device has been disconnected or is unavailable". I checked in device manager and in two categories this device appeared. Those two categories were "Modem" and "Network Adapter". Why this device comes under two categories plus why I am getting this error message?
View 1 Replies View RelatedI want to setup wireless on laptop with USB Stick connected to usb port.
View 2 Replies View Relatedi have a telstra 4g wireless broadband stick. I was wondering ifi bought a TP-Link TL-WR841ND 300M Wireless N Router 2 Detachable Antennas would i be able to plug the stick into my computer and plug my computer into the router and make the router emit the broadband usb sticks interet?
View 2 Replies View RelatedI just had to get rid of a bad DIR-825 that I replaced a trusty old DIR-655 with and now I'm back. Anyhow, I can't seem to make the DDNS setting stick in the router. All of the information is correct, but it doesn't seem to want to login. When I click the enable check box, it tries connecting and then greys out and doesn't connect.
View 3 Replies View RelatedRegion : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 06.12.2012
ISP : Entel Bolivia
I have a modem from entel in bolivia on an usb-stick.
Has anyone implemented a working Nat on a Stick?I am looking for 3750 configurations for Nat on a stick.Our users need to access the camera monitoring from home as well as in work.We will like to setup the monitoring software with public address (and port) of the cameras, as the users use the same configuration at home and work.DNS will not work for us as the monitoring settings only accept IP.
View 4 Replies View RelatedI have this Huawei E1552 (HSDPA USB Stick) and I can't figure out how to do two things: 1. I'd like to make it share it's internet connection wirelessly to other devices. I've managed to connect my PC and PS3 with ethernet cable to get connection and I believe some have managed to do it wirelessly, but I can't figure out how to get my Nintendo 3DS to find that connection. I've tried putting wireless connection in the sharing part of the connection, but it didn't seem to work.
View 5 Replies View RelatedAre the ASA memory DIMMs created for specific models? Would a 1GB 5510 Memory stick work in a 5520?
View 1 Replies View RelatedI understand router on a stick for inter-vlan routing but where I'm having trouble is having one of the vlans be public addresses. One of my clients has a rack in a colo where there is no router, i.e. their /24 public network has .1 of the network assigned to a colo router, then they have a 2960G switch in the rack that all the gear is connected to. Public IP's are assigned to certain devices / servers with .1 as their GW. Problem is, they also have a private range on the same switch with no vlans and things are a little 'cluttered' and there is no control of traffic.
The assets I have are a 2821 router with (2) GigE interfaces and the 2960G switch. A /30 network is going to assigned on the colo gear to use to push the entire /24 down to the cabinet. I'm going to NAT the local 10.100.x addresses on vlan 10 and I want the public traffic on vlan 20. During a recent test, the private traffic worked as expected but the public traffic didn't work. I don't need a complete config, more of a 10,000 ft. view of how this needs to be done so (a) traffic is vlan'd to keep things segmented, (b) I can static inside / outside public addresses from the /24 to reduce the number of public addresses being assigned directly to servers (some of this is unavoidable, but the less the better), and (c) I can NAT the local subnet to either to the /24 or the /30 (not much very much traffic in this way).
EDIT: The switch is a C2960S, not G. I cannot enable lanbase-routing, it is apparently unavailable.
* 1 26 WS-C2960S-24TS-S 12.2(55)SE3 C2960S-UNIVERSALK9-M
As per the title, I just require 3 to 4 VLANS with inter-VLAN communication enabled.
In the past I have used this router with each port of the internal switch set to a different VLAN, with each in turn hooked up to an unmanaged switch. This has work fine for me but I want to dip my toe in the world of .1q VLANS and gain some added flexibility and neatness.
Running 2k on a older Laptop, running the manufactures (Ralink RT2870 chipset) utility for a USB wireless stick causes issues so I want to try using Windows wireless utility. Problem is, I can't find how to use it. I have it running under Services. The supplied utility & drivers are installed, but I stopped loading the utility since it causes the PS2 mouse to stop responding as soon as the utility loads. The stick connects and does work, but I have no control over it without running the utility.
I tried another no name sticks software (the exact same stick, but under a different name) but it has a overly complex utility (and a newer driver), but it causes the Laptop to lock up completely.I never used a USB wireless stick before and never used wireless anything in 2k when I use to run it 6 or 7 years ago. The Laptop isn't for me.Does 2k have the ability to run a wireless device with its own utility as it does in XP, or is this because it is a USB stick, not a PCI card where the problem is?
I have not been able to figure out the resolution. The basic premise is to have 3 inside vlan networks controlled by a 1900 series router. Then have that primary LAN router connect to the inside of my ASA5505 Basic, then go out to my ISP Gateway. I have tried hundreds of different static route configurations on my router and asa. I have tried equally as many NAT and PAT configurations, but nothing seems to work. I have even tried using all the commands (specific to my topography of course) on this weblink from cisco: url...
View 12 Replies View RelatedIn my preparation for my coming CCNA certification I am experimenting with different network configurations. In my test network I am currently working with a "Router on a stick" setup. A Cisco 2611 router connecting a Cisco 2950 switch. VLANs configured on the switch and subinterfaces + dot1q encapsulation configured on the router. Switch only supports dot1q.Router's Eth0/1 is connected to the Switch Fa0/24 port which is also set to trunk mode. I am using a normal Cat5e twisted pair cable to connect the 2 devices.
VLANs are working since I can connect a workstation to an access port for example fa0/2 (vlan2) and get Internet access.I can also ping any of the subinterfaces of the router from the workstation.With the current setup I am not able to ping the switch from the router, or the other way around, so in other words I can't remote manage the switch from a telnet or SSH session with this setup. What I am missing?Just to be clear I am pinging the switch directly from the router (Router2611#ping 172.16.100.2), so please ignore all static routes and OSPF. [code]
I am trying to configure router on a stick with 2811 and 3750, but I just cannot get it to work - vlans are not getting propagated from 3750 to 2811: 3750:
Code...
Is it possible to configure remote access (IPSEC client) to force all traffic through the tunnel (no split tunnel) yet still limit the internal hosts that can be accessed?
I have been asked to provide remote access (via ASA5510) with the following requirements:
- the client should have unrestricted internet access via the ASA (the source address will appear to be the outside interface of the ASA)
- the client should have access to only two internal hosts (192.168.10.10 and 192.168.44.10)
Is there a way to limit access to those two internal hosts, while still providing secured internet access? The only way I can see is to use an access list on another device (for example our core switch).
i have a simple router on a stick config which is providing dhcp to a customer SSID. however i don't want employees to stay on it and eat the band width since its open. the lease is set to an hour, is there anyway that i could set it so that once your lease expired it can't be renewed for 4 about 8 hours? I am using a cisco 2600 router in this setup.
View 1 Replies View RelatedI have a DSL modem and Linksys WRT54G wireless router for several years and haven't had any problems. I decided to move the router and modem to a different room. Upon replugging everything in, I can't get an internet signal from my router. My modem seems to work fine-all lights are on and if I plug my laptop directly into the modem I have internet access. But, if I plug the router into the modem, I can't get internet signal both wired or wirelessly through the router. All of the lights on the router turn on-showing I should be getting internet signal [power light solid, WLAN light on, internet light on], but my computer won't open a website. I've done reboots on the modem and router. The router was working great prior to moving it. My DSL company says everything is fine on their end. I receive a Ping back from the router as well. What else should I check or do I need to do?
View 1 Replies View RelatedI have a bluray player that I want to get internet to that is downstairs. I would like to use my old Linksys WRT54g ver 2 router to do this. I just put DD-WRT firmware on it. I have a Linksys E1000 as my primary router. All I want to do is be able to to put the Secondary router (WRT54G) downstairs near the bluray player and run an ethernet cable from the lan port on the router to the ethernet port on the bluray player to get internet access. What is the best way to do this? Client bridge or Client mode?
View 2 Replies View RelatedI recently purchased a Linksys E1200 to replace my Linksys WRT54G. I'd like to utilize the WRT54G as a repeater. Is this possible, or do I need to buy a "repeater"? how to configure/set up the WRT54G repeater?
View 3 Replies View RelatedWhere do I get the WEP key for my Linksys WRT54g router?
View 2 Replies View RelatedI have an SMCD3GN which I put into bridge mode a while ago and used it as a modem alongside my Linksys WRT54G router. But the SMC is capable of Wireless N, while the Linksys is only capable of wireless G.So I want to turn my SMC into a router + modem again, but I can't figure out how to do it. I tried resetting to factory defaults by holding the reset button at the back of the unit for 30 seconds but it didn't work.I can get it to work with a wired connection, but when I type ipconfig /all into CMD, it doesn't show any default gateway, so I can't access the router online. I've tried various different IPs like 192.168.1.1, 192.168.0.1, etc., but none of them work.
View 3 Replies View Related