Can the Cisco 3750 and Cisco 2911 enforce password length? Is there a default password length? I had read the following:You can specify a password length but not special characters etc..security passwords in-length
View 1 Replieswe have installed TACAS server for all kinds of authentation. What i came to face is that when i configured enable mode password on ASA 5520 or 5510....maximum length this password is of 8 character but i need to more character.
View 10 Replies View RelatedRecently i have setup a WLAN with inside and anchor 5508 controllers. Standard setup. However, one issue I have is I wish to extend the length of time between password changes for users connected in on the guest wlan. At the moment, 30 is max. I dont have an option on the controller to creat accounts for any longer than that. How to I extend it to 90 days or 120 days?
View 1 Replies View RelatedI set the password for the router management consisting of 115 characters. Now I can not log into the router.
1. What is the maximum length of passwords to manage the WAG320N router?
2. What are valid characters in a password for this router?
We have dialup users that are connecting to our portal for uploading/downloading credit information. We are currently using ACS 3.3. There is a requirement that, initially we provide clients with their username/password, but we want to enforce the policy that when the user logs in first time, he should be prompted (forcefully) to change his password.
1) Can this be done in ACS 3.3
2) What solution shall be used in this case ? can it be done in ACS 5.3 ?
here is my situation:
home users ------ internet ------ ASA 5510----- CORP LAN
we have anyconnect VPN and remote Ipsec VPN, i think the solution should works on both of them. my question is : "How to enforce home user internet traffic to VPN tunnel ?" we have "split tunnel" to pass only ""interesting traffic" to VPN tunnel access CORP LAN. but now , i need enforce all user traffic (internet +CORP LAN) pass through VPN tunnel. so far , i did what i know :
1. remove "split tunnle" from group-policy
2. the address in "remote VPN user address pool" are could be NAT/PAT through ASA5510
but i don't get that why it doesn't work.
I logged in first time with default user ID and Password i.e.,cisco then I did wr erase and reloaded the router but I didn't change the one-time password in ISR 2911.Now its asking for user name and passworkd and cisco doesn't work.Now from ROMMON mode if I change to 0*2142 and reset it will again come back to ROMMON mode.From ROMMON mode if I type boot will come back to normal mode and ask for username and password.
View 4 Replies View RelatedI didn't change the one-time password in ISR 2911 and I can't access the CLI or the ROMMON mode
View 10 Replies View RelatedI have a network with the following structure
internet ---- cisco2911 ----cisco3750 --- internal lan
I have two email servers on different vlan
192.168.0.1 ----- 1.1.1.2 (public ip)
10.1.1.65 ---- 1.1.1.3 (public ip)
Before these servers were directly connected to the internet with two nics (Nightmare, I know). The Public IP on internet facing NIC and private ip on LAN facing nic. I'm in the process of changing this.I'm able to access internet from my vlans and also able to send emails but cannot receive emails on these servers.
My router congif is as follows:
Building configuration...
Current configuration : 6234 bytes
!
version 15.1
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
[code]....
I have a trouble with Cisco view 6.1.8. I had update offline device package because i don't have internet . When i connect to switch router 3945 and switch 3750, router 2911 on Cisco view then I receive "cannot find applicable device package for 10.1.241.10". Need to reinstall device package. The version of Cisco work LMS is 3.2. I check Active log and receive message .
The Package(s) Selected for Install :
Cat2960, Cat3750, Rtr2900, Rtr3900, Rtr7000
WARNING : Cat3750(14.0):Consistency check failed for base package DtShare
WARNING : Rtr3900(5.1):Consistency check failed for base package NGMARShare
1. set up password on a new cisco 3750 switch
2. steps to recover a lost password.
I have been asked to do a network survey at a client. They are using the Cisco SGE2000 switch, which is new to me (used to working with 3750 switches). They seem to have lost the username/pasword for one the switches. Is there an way to recover from this, without reseting the whol config (not sure they even have a backup) ..
View 1 Replies View RelatedDuring a password recovery on a cisco 3750 switch there was a power outage and now I can’t console into the switch.
View 1 Replies View RelatedI want to recover the password or set the cisco 3750 to the default password, as forget it
View 4 Replies View RelatedI want to configure " Username & Password" on Cisco 3750 switch. I need to configure as "username xxxxxx privilege 15 password 5 xxxxxxx "
Is it possible to create password with level 5 ? I want to know about level 5 "password" & level 7 "password" ?
when i tried I am not able to configure with " password 5"
I recently configured a cisco 3750 switch for a stand alone network here at work, and on all our other switches and routers we use ACS to access everything. This switch being a stand alone I dont have that option.
So being like that I have to create everyone in the shop a username and password. Is there a way to prompt the user to change their password on their first login like you would with windows or such?
Is there anyway to pull the usernames and passwords from a switch via SNMP or write a new username and password to switch via SNMP. I have switch that was apparently misconfigured and i am not feeling like driving all the way down there to console in.
View 2 Replies View RelatedCisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 19-Jul-07 19:15 by nachen
Image text-base: 0x00003000, data-base: 0x01280000
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(25r)SEE4, RELEASE SOFTWARE (fc1)
In a new Cisco 3750, if the username and password is not configured seperately, what will be the default username & password. I have only configured enable password. when we access it remotely via telnet it prompts for username/password.
View 3 Replies View RelatedI need to recover the passwords for my 3750 stack (2 switches), I have the password recovery documentation but it seems to be referring to recovery for one switch. How do I go about recovery when in a stack, should I remove the links on the switches and recover each one separately?Alternatively can I do a factory reset on them
View 1 Replies View RelatedI have lost the "ENABLE" password on my 3750 switch.
View 5 Replies View RelatedI am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
What will be the BOM for this up gradation.
I was calculating packet amount of MPEG I use byte rate to divide by 188 byte but now i want to calculate H.264 encode video what is the packet length of h.264? is it same 188byte?
View 1 Replies View Relatedmaking EEM work to show first xx lines of CPU utilization. I found when I put cli command "terminal length 13", the EEM stopped working and timed out after 20 seconds. I have tried IOS 12.4(25d) and 12.2(53) with same results. [code]
View 9 Replies View RelatedI've heard that a method to optimize traffic is to use variable length packets. They say that the worst case is in minimum length packet (64 bytes). But I can't understand why.
View 2 Replies View RelatedI used 2 PC with gigabit NIC, use cat6 with short cable i've got speed 1000Mbps, but with longer cable(around 30meters) speed is 100Mbps. I'm looking forward to seeing from you soon.
View 1 Replies View RelatedI would like to know the meaning of 'set max-parse-length 8192' on ACE.Looking at Cisco documentation I found:"you can set the maximum number of bytes to parse for generic protocols by using the set max-parse-length command in generic parameter-map configuration mode.You can set the maximum number of bytes to parse for generic protocols by using the set max-parse-length command in generic parameter-map configuration mode.' what a set max-parse-lenght is?
View 1 Replies View RelatedIs that possible to increase the pre-shared key length from 30 characters to 32?
View 3 Replies View RelatedMaximum length of cat 6 lan cable between two switch
View 2 Replies View RelatedI am installing a network in my small business and was given a spool of Cat5 cable to run wires... I know the length in feet of cable that I was given, but I was wondering if there is some kind of markers on the cable to tell me how much is left... I will be charged for it by foot after I'm done, and I want to know how much I've used. Do I have to just use a measuring tape? Seems unnecessarily complicated... I've checked the wire but can't see any marker of the length remaining.
View 1 Replies View RelatedIn order to get from the coaxial jack on my wall to my cable modem I have to run about a 50 foot coaxial cable around the perimeter of the room.Will the length of this cable diminish the speed of my internet?
View 1 Replies View Relatedi need to connect modem to computer with the length of 150m. suggest which way is efficient to connect. which cable is efficient. is any medium needed in between.
View 1 Replies View RelatedThe URL field in the web access log has a length of 70 characters. Is there any way to increase is[INFO] Mon Jun 13 21:30:30 2011 Website1234567890012345678900123456789001234567890012345678900123456789001234567890 accessed from 192.168.xx.xx
View 2 Replies View Related