Cisco :: 4402 Can Control The Meraki MP12
Feb 5, 2012We have a 4402 Wireless Controller. However, our AP's are from another manufacturer (Meraki MP12). Is it possible that the 4402 can "control" the Meraki MP12?
View 8 Replies
ADVERTISEMENT
Cisco :: WLC 4402 And LWAP 1510 / Access Control List?
Aug 18, 2011We have WLC 4402 and LWAP 1510In access control list menu, all needed rule added and the last rule deny any to any We use Ethernet bridging on LWAP and some clients connect with wire network that associated with Ethernet bridge LWAP, Now when deny rule applied the client that connect with wired network couldn't established VPN connection or another service to the routing and remote server, I create rule that permit any to routing and remote server.
View 1 Replies View RelatedCisco Wireless :: 4402 - Data Path Down Control Path Up
May 5, 2010have just set up a WLC 4402 as a Guest WLAN controller on the DMZ of our network. I have successfully managed to get our internal controllers to connect to it, with the exception of 1. it says the control path is up but the data path is down. the other 14 controllers worked fine, and in testing the last one was OK but it is now not working properly. the 2 controllers can ping each other but just won't create the data tunnel. there is a firewall in the middle but that has been set up to allow traffic between the 2 groups of controllers to be unrestricted.
the internal controllers are 4404's and all controllers are running the same version of code. 5.1.151.0.
Cisco :: WLC 4402 - Which Version Of WCS To Use
Dec 4, 2011I am running a WLC 4402 with software version 6.0.182.0. Which WCS version should I use or does it matter?
View 5 Replies View RelatedCisco :: Upgrading WLC 4402 From 4.2.176.0 To 7.0.230.0?
Apr 7, 2012I am in the process of upgrading my 4402 to version 7.0.230.0 and am confused on the premise of the firmware and the bootloader. From what I currently understand, I can upgrade directly to the 7.0.230.0 firmware from my current 4.2.176.0, then I should upgrade to the latest bootloader image. But I have also seen posts where I should update the bootloader software to the latest version, then put on the latest firmware.
I have seen conflicting reports where I must step through each bootloader version, 4.x to 5.x to 6.x to 7.x to make sure I have all the fixes, but I have also seen instructions, where you can jump to the very latest and the fixes are cumulative.
Cisco :: Flash And RAM Installed In WLC 4402?
Feb 9, 2011I am looking around hwo to know the flash and ram installed in WLC 4402? try looking any command, sh ver not there. even in WCS.
View 2 Replies View RelatedCisco :: 4402 - How To Distribute SSID To Only Few AP's
Nov 12, 2012we have a 4402 controller with sw 7.0.116 and a wcs with sw 7.0.172.
We have to create a new wireless network, and would like to send the ssid to only one AP. Is this possible ?
Cisco :: 4402 - Allow Certain Ip To Access To Log In Page Of WLC
Apr 29, 2013I have a cisco WLC 4402, i have a problem with people trying to log into wlc 4402 GUI console with wrong pass. Are there any ways that I can allow certain IP to go to or see the log in page of WLC?
View 5 Replies View RelatedCisco :: Certificate Authentication At WLC 4402
Jan 18, 2012we are using Cisco Aironet 1130 AG and a Cisco 4402 WLC in our network. The certificate service is installed on a Windows 2008 R2 server. We use a standalone Root CA with a Enterprise Sub CA hierarchy. Issueing certificates to clients works fine. The vendor and ca certificates are installed on the WLC and the user have his user certificate. During implementation we used following document: url... Instead of Anonymous Bind, we use a service user to read in AD (works fine, too).
We use the Intel/PRO wireless utility on our Testclient and configured it for EAP-FAST and TLS. We can select the installed certificate in the utility, but when we try to connect, the utility throw the message: "Authentication failed due to an invalid certificate".We´ve logged the WLC and thats a part of the logfile (i´ve greyed out all enterprise data): [code]
Cisco Wireless :: Can't Get APs To Recognize 4402 WLC
Nov 20, 2011I have 2 4402 WLC's and am in the process of deploying 1042 APs out to sites. But The AP's wont recognize the WLC. I have configured the DNS for CAPWAP but still no dice. I have had to serial into each unit and give it a static IP and then I can see it on the WLC. Shoulsnt this be automatic?
View 21 Replies View RelatedCisco :: 1242AG-A-K9 AP's Not Registering To WLC 4402
Jan 1, 2007Currently have a WLC4402 installed with 21 AP's reporting to it. The controller is running at LWAPP3 with version 3.2.116.21. The WLC was purchased prior to Cisco buying Air-e-space, and has a 36 AP license. When attempting to install additional 1242AG-A-K9 ap's, the controller will not acknowledge them. I have verified the LAN confiuration as correct, and working properly.
View 9 Replies View RelatedCisco Wireless :: WLC 4402 Has Detected Its IP Add Being Used By Mac
Jul 29, 2010Any explanation about this warning from the WLC4402 after the software upgrade to 7.0.96. version? this is the message: Warning: WLC has detected its IP add xx.xx.xx.xx being used by a machine with MAC add xx:xx:xx:xx.and the MAC add found is the the mac add of the dynamic interface of the WLC.
View 7 Replies View RelatedCisco :: How To Export Cert From WLC 4402
Apr 1, 2013I installed a chained SSL cert on our anchor/guest 4402 a few years ago.We now have a need to replace the 4402 w/ a 5508, and I got everything configured, ready to go, except that darn cert.I can no longer locate the private key that was used to sign the original CSR.Is there any way to export the current cert from the 4402, so that I can import to the 5508? Or am I SOL?
View 3 Replies View RelatedCisco :: WLC 4402 Not Implementing PEAP?
Jul 24, 2011I was able to successfully implement MS-PEAP authentication with 5508 WLAN controllers and Cisco ACS v4.2. However, when I integrated 4402 WLC with version code 7.0.116, it did not pass across any authentication requests. Did a debug aaa events enable and there was no output. Configured another SSSID with PSK to test that my controller was OK and aaa debug was working, and there were CLI messages when I associated an AP.
why the 4402 is not working as I have compared configs with the 5508 and there is no difference. The shared secret is configured on both ACS and Controller and CA is downloaded on the ACS.
Cisco Wireless :: 4402 WLC Cannot Join More Than 47 APs
Jun 29, 2011My WLC running 6.0.182.0 suddenly could not accept more than 47 APs! Ihave a 1240 trying to join but failed with no obvious reason (no special errors in debugging).
I unplugged one of the joined and the first one joined!! I replugged the second one but could not join!! I unplugged the first one and replugged the second one: the second joined the controller but the first could not associate again!
Cisco :: Client Cannot Communicate Between Each Other WLC 4402
Mar 27, 2012My client cannot communicate between each other, why ?
Controller: AIR-WLC4402-25-K9
AP: AIR-LAP1252AG-A-K9
Cisco :: 4402 WLC / LMS 4.2 Threshold Coming
Mar 1, 2012I'm using RADIUS and FlexConnect APs. The issue is intermittently users will lose connectivity as if they're de-authenticated. Their clients still believe they're associated to wireless but they have no network connectivity. On Windows 7 we receive the exclamation point over the signal strength indicator.
There doesn’t seem to be any rhyme or reason as to what is causing this. It doesn’t seem to happen at any particular time intervals or anything else I can identify. Sometimes users will go entire days without experiencing connectivity issues sometimes they can’t go five minutes. When the clients are experiencing the issues they cannot even ping their default gateway.
The setup was initially the following:
Site A: 1142N APs and RADIUS server (server 2003) users are authenticating to.
Site B: Flex 7510 running code 7.0.116
Between site A and site B there is a site to site VPN with no restrictions.
After some time of working with TAC and not getting anywhere I setup the following:Site A: 4402 WLC running code 7.0.116 connected the same 1142N APs HREAP mode. I had the same issue with connectivity with that setup.Today I changed over to local mode and as of yet I haven’t had reports of connectivity issues.
When running ‘debug client MAC’ I see no indication of connectivity issues. I also have an NCS and I don’t see anything indicating what the issue is there as well. I’ve tried with both enabling and disabling ‘H-REAP Local Auth’. We seem to experience the issue in H-REAP standalone mode as well.
Cisco Wireless :: AP Supporting 4402 WLC?
Jun 25, 2012Can 3600 series model AP work with WLC 4402 with existing license, we purchased 25 LIC pack and still using only 15. Any recommended Part no on 3600 series with external Antenna
View 5 Replies View RelatedCisco :: 4402 / Wlc Max Database Size?
Jun 28, 2011I have a 4402 being used as a dmz anchor and we use WCS to allow our Helpdesk to create lobby ambassador accounts. Recently they have been getting error messages when attempting to create accounts. I am seeing the database maxxed out at 2048. The docs state database entries are made up of mac filters(don't use)..ap mic/ssc(don't use)..Dynamic interfaces(minimal) management users(2) local netusers (100 approx)..and excluded clients(none). So the numbers don't add up.I am on 4.2.61.0 code.. I will say also that WCS shows alot more netuser accounts than my anchor does but no where the numbers to max out the database. Is there some other criteria that hits against the datasbase number?? And what can I do on the WCS to insure it si synch'd up against the dmz anchor other than a audit..
View 3 Replies View RelatedCisco Wireless :: AP 1262 Cannot Join WLC 4402
Jun 7, 2012We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
Cisco Wireless :: AAA Authentication Failure On WLC 4402?
Jun 13, 2012Error: AAA Authentication Failure for UserName:radiususername User Type: WLAN USER
I am using a window radius server. I have added my WLC 4402 as a radius client on my radius server.
I followed the instructions on the MS link : [URL]
I want to use my windows raduis authentication for WLC management login and Web-Auth for guest WLAN user login.
Cisco Wireless :: 4402 Code Upgrade To 7.0.230.0
Feb 3, 2013Our company has a customer with a Cisco 4402 WLC and a code version of 4.2.130.0 . The customer wants to upgrade the code to 7.0.230.0. Is there any flash size requirement when upgrading to 7.0.230.0? (upgrade train: 4.2.130.0 ----> 4.2.209.0 ----> 7.0.230.0), How can I find the flash size?
View 2 Replies View RelatedCisco Wireless :: Configuration Migration Of WLC 4402
Feb 3, 2013We got WLC 4402 running software 7.0.235 and would like to backup the configuration and restore on 5508. Is this doable? Do we need to be on the same version as WLC 4402. How to get cisco document to follow the steps if the above is doable,5508 is new with no setup.
View 6 Replies View RelatedCisco :: 4402 Would Be Replaced At A Remote Site
Apr 8, 2012I need to replace a 4402 with a 2504 controller and put a 2504 controller in the DMZ for guest access. The 4402 would be replaced at a remote site (not hreap) and support a couple of wlans, one of those would not be local and would be anchored back to the 2504 in the DMZ for the guest services. All of my 5508's also would be hitting the 2504-DMZ to anchor the guest service as well. Is this still feesable in the 2504 series?
View 4 Replies View RelatedCisco Wireless :: How To Connect One 5508 And 4402
Jan 16, 2012I need to install one 5508 and a 4402 together to bring redundancy to a wireless environment.Can I do this?. What are the neccesary steps to perform this?, the idea behind this is to bring redundancy is the primary WLC falls for any reason.
View 4 Replies View RelatedCisco :: Setting Up NPS With 4402 Wlan Controller?
Jul 4, 2011I am currently running a Cisco 4402 Lan controller, I have a Wlan that is running unsecured and i wanted to add a simple web policy log in, so i set up an NPS server on a local DC. I have the two talking . when i go to login at the web login page I get the Error Login Error. When i look at the NPS logs it says: "Network Policy Server granted full access to a user because the host met the defined health policy" . So it has to be in my Cisco set up somewhere seems pretty simple
View 2 Replies View RelatedCisco :: Wlc 4402 - Wireless Client Ip Address?
Mar 7, 2011I have two wlc 4402 to control 50 AP 1131. 2 WLC: wlc-01 and wlc-02, wlc-02 config as backup wlc in the same mobility group. Client authentication:EAP with Microsoft IAS/AD.All AP have joined wlc-01. Wireless client work well with wlc-01.For testing I config access point AP01 have primary wlc: wlc-01, secondary: wlc-02 If I change config of AP01 like this: primary wlc: wlc-02, secondary: wlc-01. Client is hard to connect to wlc-02 and it only connect when client set static ip ALL wlc run this softwar image: 7-0-98-0 Should I send wlc-02 to warranty service?
View 8 Replies View RelatedCisco :: WLC 4402 Radius Override Disabled?
Sep 15, 2010Recently we've been receiving the following log entries on our WLC 4402. Unfortunately Cisco's documentation is less than useful as to what this message means or what could be causing it. [code]
View 9 Replies View RelatedCisco :: Wlc 4402 4.2.61 Unable To Add Mac Entry To Database
Apr 30, 2012When I try to add new MAC entrys to the WLC I get the following message unable to add mac entry to database, reached max size the problem is when I look at the stats there is only 386 MAC entry and the databse size was set to 1024 entry..The work around was to increase the size of the database to 2048.Is there any why to clean up the database?
View 2 Replies View RelatedCisco :: 4402 WLC - Restrict Lobby Admin
May 12, 2011I was wondering if there is a way to limit the ability of the "lobby admin" account to only be able to give out 24 hour wireless access? The situation is this, we are going to move the roles of guest wireless over to our lobby administrators, but we are afraid they might break policy and give out 30 day wireless access so they dont have to keep renewing guest access each day. We want to limit access to 24 hour "tokens" for all guest unless its a unique situation.
View 2 Replies View RelatedCisco Wireless :: 4402 Could Not Register IP Add On MSCB
May 17, 2012I do get this error all the time on my WLC 4402 logs:
"Could not Register IP Add on MSCB. MSCB still in init state. Address:e4:ce:8f:13:e4:de[...It occurred 2 times.!]"
Cisco :: WLC 5508 - Possible To Anchor To 4402 Running 7.0.116.0
Apr 23, 2012We are deploying two 5508 WLC running 7.2 ios. Is it possible to anchor these to a 4402 running 7.0.116.0. Is there any version mismatch issues. We can find documents on the older compatibility but not on the new code.
View 9 Replies View RelatedCisco Wireless :: WLC 4402 Ver 5.1.151.0 Working With Air-ap1041n-e-k9?
Jul 18, 2012I have WLC 4402 working with AIR-AP1131AG-E-K9. Need to buy another pair. I looked to the side air-ap1041n-e-k9. Tell me whether or not the compatibility of the controller and the AP1041n? One more question. When buying in 1131 is still in the box and power cord to the point. The new 1041, the purchase comes with the point of the power cord?
View 13 Replies View Related