Cisco :: WLC 4402 Radius Override Disabled?

Sep 15, 2010

Recently we've been receiving the following log entries on our WLC 4402. Unfortunately Cisco's documentation is less than useful as to what this message means or what could be causing it. [code]

View 9 Replies


ADVERTISEMENT

Cisco Wireless :: DHCP Server Override On 4402 WLC

Apr 17, 2012

I have successfully implemented wireless guest access using 4402 WLC as the Anchor and 5508 as Foreign. The Anchor controller also provides dhcp services to guest clients. The 5508 is LAGged and there is no issue with the guests traffic separated from corporate. At a remote site, there is a 4402 WLC using LAG and also acting as a Foreign controller. But when a client connects to the guest WLAN, it obtains a corporate dhcp address instead of the dhcp address assigned from the Anchor controller. The guest WLAN setting is the same as with the 5508 controller i.e. DHCP server override is ticked and the management IP address of the Anchor controller is specfied. Also DHCP Addr required is ticked. Why the 4400 controller is not forwarding dhcp requests to the anchor controller and instead sending to the corporate dhcp server.

View 36 Replies View Related

Cisco :: 4402 - How To View Logs Of Disabled MAC Addresses

Jan 4, 2011

I have a Wireless LAN Controller 4402 and WCS 7.0, and I have a few MAC addresses that are "disabled" due to policy violations. How can I view a log or a report that will show me if these MAC addresses are still attempting to connect?

View 3 Replies View Related

Cisco Wireless :: How To Modify RADIUS Servers On 4402 Controller

Jul 20, 2010

I have several controllers, including a 4402 running 6.0.188.0 software and I need to modify the Radius servers that it uses. Currently I have three servers listed;

1 - 10.246.194.16
2 - 10.200.31.78
3 - 10.247.50.56
 
I would like to delete server 1 which is being retired and replace it with a new server 1. I suspect, once i get servwe 1 deleted, the server 1 option would become available when I create a new server. I went into the controller and disabled server one, but every time I try and delete it, I get the "Server in use either on a specific WLAN or Mesh Radius Server Configuration" error. I can't find anywhere this server is still in service and being used, either by a WLAN or a Mesh. I've tried several different variances to modify this. What I hope to avoid is the need to reset the controller. I have a total of seven controllers that I need to make this modification to, and It will be ugly if I have to reboot these units. Hospital mission critical stuff.

View 4 Replies View Related

Cisco :: WLC 4402 Web-authentication Fail With External RADIUS Server

Jul 3, 2007

I follow step by step the link bellow to configure web-auth with external RADIUS server but I receive a error on console debug of the WLC "Returning AAA Error No Server (-7) for mobile"My Radius Server is fine, because I can authenticate on WLC Web page with RADIUS user.  WLC 4402 version 4.1.171.0 [URL]

View 2 Replies View Related

Cisco Wireless :: 4402 WLC Web Interface Missing Buttons When Logged Through Radius?

Feb 12, 2012

I have a Cisco 4402-25 WLC with the below information that is having an interesting issue. When you log into the GUI interface with the local account and click on WIRELESS, then choose a accesspoint it brings up a menu where you have three buttons below for the following options (Hardware Reset - Reset AP Now), (Set to Factory Defaults - Clear All Config), and (Set to Factory Defaults - Clear Config Except Static IP). The problem I am having is we access all of our WLC's using Radius and when you enter your AD username and password and go to bounce a access point the GUI interface is missing the buttons, they however appear fine when logged in with the local account. 

System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.220.0
RTOS Version..................................... 7.0.220.0
Bootloader Version............................... 4.0.206.0
Emergency Image Version.......................... 5.2.157.0

View 2 Replies View Related

Cisco WAN :: AS 65000 Override Connection

Mar 26, 2013

{10.46.0.254/32 is advertised on R1 (AS 65457)} ••>AS (3549) -->AS (4058) ---->AS (17776) ••>R2 (local AS 65458) ••>R3 (local AS 65457) ••>AS 65000 ••>{ R4 (AS 65457) advertises 100.9.254.0/24}
 
Scenario 1:                                                                                                                                                                                                                                                                                                                                                                                         
R2 and R3 are eBGP peers on LAN..
 
R1#show ip bgp neighbors 10.117.36.89 adv
BGP table version is 72, local router ID is 10.46.0.254
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
             r RIB-failure, S Stale, m multipath, b backup-path, x best-externa
[Code]...

View 5 Replies View Related

Cisco VPN :: ASA 5505 - How To Override Split Tunneling Per User

Nov 5, 2012

I've an ASA 5505, running at ASA 8.2(2). I'm using ASDM 6.2(5).ASA is set up with Split Tunneling and it works perfectly.However, for a few users, I want all traffic, including Internet traffic, routed through the ASA.The spesific users IP address at internet should then be the same as ASA Outside address, not the client local address.The question is therefore:How to simple override the split tunneling at user level?Alternatively set up an "tunnel all" group policy for the specified users?

View 19 Replies View Related

Cisco :: WLC 5508 802.1 AAA Override - Authentication Success No Dynamic

Nov 28, 2010

WLC 5508: software version 7.0.98.0
Windows 7 Client
Radius Server:  Fedora Core 13 / Freeradius with LDAP storage backend
 
I have followed the guide at URL with respective to building the LDAP and free radius server.  802.1x authorization and authenication correctly work.  The session keys are returned from the radius server and the wlc send the appropriate information for the client to generate the WEP key.
 
However, the WLC does not override the VLAN assignment, even though I was to believe I set everything up correctly.  From the packet capture, you can see that verfication of client is authorized to use the WLAN returns the needed attributes:
 
AVP: l=4  t=Tunnel-Private-Group-Id(81): 10
AVP: l=6  t=Tunnel-Medium-Type(65): IEEE-802(6)
AVP: l=6  t=Tunnel-Type(64): VLAN(13)

View 8 Replies View Related

Cisco WAN :: Ip Pim Address Access List Override 6506

Apr 22, 2013

We have a three tier network with a centralized core switch and multitple distirbution swithces - all 6506 routers.EAch dist switch is its own PIM SM domain and the RP so we never send multicast between the dist switches and through the core.
 
We are putting in a centralized server at the core switch which has to provide specific mcast < X Groups > to all servers at the dist level on all dist switches.
 
So we would like to define the RP <core rp ip>  just for the   <X groups> on the Core switch and tell all the distribution switch that the core is the RP for just the <XGroups>
 
If we put these commands on all the switches including the cores will that set the rp just fo the <XGroups> to the <core rp ip > ?Do I have to define the deine an ACL for all groups if i define it for some or will groups not defined by the ACL defualt to the local RP?
 
do I have to put in the override command ? (We are using MSDP not autorp)
 
ip pim rp-address <distn rp ip>
ip pim rp-address <core rp ip> 99

ip access-list 99
permit <XGroups > mask

View 1 Replies View Related

Linksys Wireless Router :: E3000 - Override Only DNS From ISP

Nov 3, 2012

I would like to override the DNS servers provided by DHCP via my ISP. The other settings I would like to preserve (like my assigned IP).How to achieve this with E3000 ?

View 3 Replies View Related

Routers / Switches :: Override Administrator Login Windows 7?

Apr 25, 2011

every time i go to my log in it ask for a pass word i did not make a pass word i have put in all kinds of pass words and got no where it will not even give me a hint i have went to safe mode it still ask for pass word . i have windows 7 how to rid the problem so that i can get around the administrator and remove it so that i can make another administrator account.

View 3 Replies View Related

Want The Sim Card With PIN Disabled?

Oct 3, 2011

i want the sim card with PIN disabled so that it can be used with GSM modem for data communication

View 3 Replies View Related

D-Link DIR-655 :: Wan Is Disabled Already Or Not

Jan 5, 2012

Now that WPS has been cracked (you can get "reaver" on the internet to run on your Linux laptop or VM), it has been found that several routers that have WPS disable/enable controls in their web GUI's are still vulnerable to attack.Has anyone verified whether or not that's the case with the DIR-655?  I was feeling pretty good about my router until I read that some routers are still vulnerable to this attack even with WPS disabled in their web controls.It would be nice to get confirmation for this router on whether I need to stop using it (no open source firmware available that I know of).

View 14 Replies View Related

Cisco :: LMS 4.0 Disabled DHCP Client

Jan 23, 2012

I have a fresh install of LMS 4.0 on Windows Server 2008 Standart SP2. I have one NIC with static IP configuration. I also disabled DHCP client.The problem is follows: when I go to Inventory - Device Administration - Add/Import/Manage Devices, I always get this error:Error in communicating with DCR Server. DCR Server may be down. Please start the DCR Server and then refresh the page.Reload server/ Daemon Manager dont solve this.I try to beat this problem 2 days already. Second uninstall also doesnt solve the problem..
 
About a week ago I tried to clear log files which was 270gb (syslog.log) and after that restarted the server. And all inventory devices suddenly disappear! I could find it from search menu but cant access - cisco works said that there is no such a device in Device Repository or I havent enough right to view it (but i logged as admin). And after this i failed to add any device in Inventory. So I reinstall Cisco Works and get that DCR error..

View 1 Replies View Related

Cisco WAN :: 2911 / PBR Only Works With IP CEF Disabled

Jan 16, 2013

We have a PBR configured on a 2911 router (15.1-4.M2).  The PBR is being used to send specific traffic across a S2S VPN instead of an MPLS connection.  If ip cef is enabled, the router sends the traffic across the MPLS.  If ip cef is disabled, the traffic goes across the S2S VPN.  I checked to see if there were any bugs in the code they are running about this and nothing came up.  It almost like CEF enabled PBR isn't working on this device, even though it should be enabled by default when ip cef is turned on.

View 3 Replies View Related

Cisco Routers :: RVS4000 With FTP When IPS Disabled

Jan 11, 2012

I've been trying to disect this problem for a few months to no avail. The router allows me to connect to outside FTP only when IPS is enabled. The moment I disable the IPS functoin, the connection hangs and does not connect to a server. Reason I'd like to keep IPS disabled it is because it's eating up half of bandwith when enabled.RVS4000

View 2 Replies View Related

MLS QOS Disabled - How Much Interface Buffer Available

Apr 11, 2012

When mls qos is disabled, how much of an interface buffer is available to the single output queue?is a single switch port able to consume as much as required of the common memory pool.

View 7 Replies View Related

Wireless And Bluetooth Is Disabled

Jan 19, 2012

ive got some problems with my HP pavilion dv6000...i have recently reinstalled pc with windows xp home edition..installed drivers recommended on the HP official webpage and in HP wireless assistent still states that Wireless and bluetooth is disabled..but in device manager is enabled. also with my audio driver .already installed but dont make any sound.

View 2 Replies View Related

Wlan Disabled And Cannot Enable It

Dec 31, 2011

I recently tried to connect to my wireless broadband and the icon had disappeared. I went into control panel and wlan assistant and tried to enable the wireless.A message comes up saying it is trying to install software for Broadcom 802.11b/g WLAN.I run through the process but then when I try and get on to network controller I get the message there was a problem installing this hardware. It says This Device is disabled (code 22)

View 1 Replies View Related

WLAN Is Turn Off Or Disabled

Oct 13, 2012

"Your WLAN is turned off or disabled. Follow the instructions in HP Wireless Assistance to turn on or enable the WLAN before continuing".I have a HP Pavilion tx1000 and no wireless network is working only LAN connection which i never use this before with my computer.

View 1 Replies View Related

Wifi Disabled Can't Enable It?

May 4, 2011

I have tried everything! My wifi disabled itself some how, i have a toshiba satellite and the fn f8 button is no longer there to turn my wifi on and off. I tried reinstalling the driver it didnt work. Its up to date. I also tried to restore my computer back to the last time it worked and that didn't work. I tried starting it in safe mode with networking and that didn't work. I can connect to the internet but through a wire.

View 10 Replies View Related

Cisco Firewall :: 5520 As ISP Causes VPN To Be Disabled When Using Contexts

Jan 31, 2012

In the latest code, is VPN still disabled when using contexts? If you use a 5520 as an ISP based firewall for customers, then what would be used for VPN access?  Also how many contexts does a 5520 support, and would putting 2 interfaces into an etherchannel for inside, and 2 for outside work?  Reason I ask about that, the inside and outside would connect to 2 different core routers.  I would be for an MPLS setup.

View 5 Replies View Related

Cisco Wireless :: AIR-CAP2602I-E-K9 Command Is Disabled

Nov 5, 2012

I'm configuring AIR-CAP2602I-E-K9 out of the box, literally, and I want to configure it with a static address. I paste in the following commands. [code]After the host name line is pasted in I get "ERROR!!! Command is disabled" but the rest of the commands are accepted. I do a sh capwap ip config and the get the output below which looks like that config has been taken but why not my hostname? [code] I know or hoping that the APs will contact the wireless controller since I've the ip in there for it. It just means I'll be renaming all the APs, all 18 of them!

View 6 Replies View Related

Cisco :: WLC 4404 Wireless Users Getting Disabled

Dec 28, 2011

Currently Being Moderated Wireless users getting disabled

View 6 Replies View Related

Cisco Firewall :: 5520 NAT Control Is Disabled

Jun 28, 2012

ASA 5520
version 8.2
 
My client has the inside network on interface gig0/1.100 and the guest network on gig0/2.200.  The whole 10.77.1.0/24 network needs to be able to reach the server with IP 10.47.47.80 using HTTP.  The access list is in place ont the guest interface to allow traffic to the server.  The problem is that when I do a packet trace to see the traffic flow, it is dropped on a NAT rpf-check. NAT control is disabled. [code]

View 2 Replies View Related

Cisco WAN :: 851 - Password Recovery Functionality Is Disabled?

May 31, 2010

the " password recovery functionality is disabled " service is running on the system .
 
im trying to access rommon in a Cisco 851, with not much success, i am sending a break after the image is loaded ( in the time frame that is allowed for that) .

View 13 Replies View Related

Cisco Routers :: WRP400 Nat Disabled - Can't Reach WAN

Oct 9, 2012

[URL]
 
This router support bridge mode, but i'm unable to configure it. There's no such option in the web configuration page, but the manual says that disabling nat activates automatic routing mode. Unfortunately all i get when i disable nat is to be unable to reach any wan address.
 
By watching the generated routing table on the wrp400 (when in NO nat mode) i see that 0.0.0.0 is correctly set up to use the external border router, but any incoming packet from the wrp400 lan port isn't routed there.
 
Also, i don't get any dhcp from the external router, this means the wrp400 is blocking it.
 
how to set up a bridge mode between wan and lan ports

View 1 Replies View Related

Windows 7 - Network Adapter Is Disabled

Apr 15, 2013

I am using Windows 7, suddenly my network adapter has been deleted and i am unable to use Internet

View 7 Replies View Related

Wireless :: BMC4311 Is Missing And Disabled

Jan 28, 2011

I tryed going into bios and disabled it and reabled it still its not working, tryed to uninstall it and reinstalled it still not working

View 1 Replies View Related

Media Disabled Message In Vista

Apr 15, 2011

I seem to be having the same media disabled message in Vista. How do I proceed with this type of refresher in Vista? Out of the blue, no networks can be detected on this particular laptop. I have tried uninstalling the HP WLAN program so far.

View 5 Replies View Related

WLAN Has Been Disabled / Computer Crashed

Mar 28, 2011

About 5 days ago the computer crashed. I was able to reload Windows XP and load all the drivers and hardware. The only problem is, now the WLAN is saying that it is disabled and I am unable to enable it. The stupid thing about this is, when the computer crashed, the next day i was able to get on. The WLAN was working just fine and so I decided to go ahead and load windows anyways because it has been having issues. Every since I did that, the WLAN has been disabled.

View 10 Replies View Related

Disabled Wireless Radio On Westell

Feb 16, 2013

I have a westell DSL modem/router supplied by Frontier. It connects only to the telephone line and via cat5 to my main router, a cisco EA6500. Everything seems to be working fine, I just would like to understand a few things.I disabled wireless radio on the westell, enabled it on the cisco, so I have just one WIFI network active.I know I am not supposed to have two DHCP servers active, but I did not know how else to be sure the CISCO would get a good address, so I left DHCP active on the WESTELL, and also enabled it on the CISCO to provide service for the rest of the net.The WESTELL admin interface is at 192.168.1.1, and assigns addresses in this range.According to the WESTELL, the CISCO is at 192.168.1.27, which I assume was assigned by DHCP.The CISCO has an admin interface at 10.144.224.224, and assigns addresses in this range to all the other devices on my net.As I say, everything works.I can access both router admin pages with a browser on my main 10.144.224 network, and can ping both.But I don't understand why it works.What rules allow me to talk to the WESTELL admin page from the CISCO private network, but do NOT propagate the DHCP access which is at the exact same IP address.

It is great that it works. But should I really have disabled DHCP on the WESTELL and assigned a static address to the CISCO? Or is this situation actually provided for in the rules, not just a lucky accident that it works?Why does the scanner say that the CISCO DHCP is "Unknown" rather than Authorized or Unauthorized? Is there something I can or should do to get it to be "Authorized"? I can ping 192.168.1.1, but not the 192.168.1.27 (times out), and yet when I ping a non-existent 192.169.1.3 I get "Reply from 192.168.1.27: Destination host unreachable".

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved