Cisco WAN :: 2911 / PBR Only Works With IP CEF Disabled
Jan 16, 2013
We have a PBR configured on a 2911 router (15.1-4.M2). The PBR is being used to send specific traffic across a S2S VPN instead of an MPLS connection. If ip cef is enabled, the router sends the traffic across the MPLS. If ip cef is disabled, the traffic goes across the S2S VPN. I checked to see if there were any bugs in the code they are running about this and nothing came up. It almost like CEF enabled PBR isn't working on this device, even though it should be enabled by default when ip cef is turned on.
View 3 Replies
ADVERTISEMENT
Jun 5, 2012
I'm very new to cisco devices but we recently acquired a catalyst 2911 device for our co-lo cabinet and I am trying to get a site-to-site vpn connection working between the facility and my offices network as well as a remote access VPN for me to use in case I have to fix something while outside of the office.
The office's gateway is 66.119.163.2 and the device is a TZ210 with it's LAN network being 192.168.1.0 /24
The co-los gateway is 204.244.50.254 and the device is an ASR 2911 with it's LAN network being 10.0.10.0 /24
The S2S VPN connection is up between the two locations and the 2911 device and the servers within it's LAN can ping and RDP to the office's machines. The office network can only ping the LAN interface IP on the 2911 which is 10.0.10.1 but not the servers in the network. the site-to-site VPN was set up with the CCP wizard.
How can I allow the 192.168.1.0/24 network to see the 10.0.10.1/24 network and why do I only currently see the gateway?
If need be I can post my running-config file with the preshare keys redacted.
View 8 Replies
View Related
Sep 4, 2012
how this switch module works in 2911 router? I have two 2911 routers in HSRP configuration for redundancy with crossover cable between switch modules. OSPF running on routers.If active router loses its power and then comes back again, it boots first, its internal link to switch module comes up and it starts to forward packets to switch module. The switch module starts to boot only after router is ready. So I have outage of about 3-4 minutes. For our real-time applications it is way too long.
any way to start booting of the switch module before router gets ready?I understand I can boot it manually, but it is only after router is ready. Only way to get around it I found is to disable internal link and use router interface to connect to the switch module.
View 1 Replies
View Related
Dec 25, 2011
I am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
What will be the BOM for this up gradation.
View 2 Replies
View Related
Apr 6, 2011
this computer was working on this router no problem. computer crashed and noiw computer is fine i connected it to my cable from ny desk top comutyer and works fine. It just cannot hook up to the wireless connection?
View 1 Replies
View Related
Oct 3, 2011
i want the sim card with PIN disabled so that it can be used with GSM modem for data communication
View 3 Replies
View Related
Jan 5, 2012
Now that WPS has been cracked (you can get "reaver" on the internet to run on your Linux laptop or VM), it has been found that several routers that have WPS disable/enable controls in their web GUI's are still vulnerable to attack.Has anyone verified whether or not that's the case with the DIR-655? I was feeling pretty good about my router until I read that some routers are still vulnerable to this attack even with WPS disabled in their web controls.It would be nice to get confirmation for this router on whether I need to stop using it (no open source firmware available that I know of).
View 14 Replies
View Related
Jan 23, 2012
I have a fresh install of LMS 4.0 on Windows Server 2008 Standart SP2. I have one NIC with static IP configuration. I also disabled DHCP client.The problem is follows: when I go to Inventory - Device Administration - Add/Import/Manage Devices, I always get this error:Error in communicating with DCR Server. DCR Server may be down. Please start the DCR Server and then refresh the page.Reload server/ Daemon Manager dont solve this.I try to beat this problem 2 days already. Second uninstall also doesnt solve the problem..
About a week ago I tried to clear log files which was 270gb (syslog.log) and after that restarted the server. And all inventory devices suddenly disappear! I could find it from search menu but cant access - cisco works said that there is no such a device in Device Repository or I havent enough right to view it (but i logged as admin). And after this i failed to add any device in Inventory. So I reinstall Cisco Works and get that DCR error..
View 1 Replies
View Related
Jan 11, 2012
I've been trying to disect this problem for a few months to no avail. The router allows me to connect to outside FTP only when IPS is enabled. The moment I disable the IPS functoin, the connection hangs and does not connect to a server. Reason I'd like to keep IPS disabled it is because it's eating up half of bandwith when enabled.RVS4000
View 2 Replies
View Related
Apr 11, 2012
When mls qos is disabled, how much of an interface buffer is available to the single output queue?is a single switch port able to consume as much as required of the common memory pool.
View 7 Replies
View Related
Jan 19, 2012
ive got some problems with my HP pavilion dv6000...i have recently reinstalled pc with windows xp home edition..installed drivers recommended on the HP official webpage and in HP wireless assistent still states that Wireless and bluetooth is disabled..but in device manager is enabled. also with my audio driver .already installed but dont make any sound.
View 2 Replies
View Related
Dec 31, 2011
I recently tried to connect to my wireless broadband and the icon had disappeared. I went into control panel and wlan assistant and tried to enable the wireless.A message comes up saying it is trying to install software for Broadcom 802.11b/g WLAN.I run through the process but then when I try and get on to network controller I get the message there was a problem installing this hardware. It says This Device is disabled (code 22)
View 1 Replies
View Related
Oct 13, 2012
"Your WLAN is turned off or disabled. Follow the instructions in HP Wireless Assistance to turn on or enable the WLAN before continuing".I have a HP Pavilion tx1000 and no wireless network is working only LAN connection which i never use this before with my computer.
View 1 Replies
View Related
May 4, 2011
I have tried everything! My wifi disabled itself some how, i have a toshiba satellite and the fn f8 button is no longer there to turn my wifi on and off. I tried reinstalling the driver it didnt work. Its up to date. I also tried to restore my computer back to the last time it worked and that didn't work. I tried starting it in safe mode with networking and that didn't work. I can connect to the internet but through a wire.
View 10 Replies
View Related
Jan 31, 2012
In the latest code, is VPN still disabled when using contexts? If you use a 5520 as an ISP based firewall for customers, then what would be used for VPN access? Also how many contexts does a 5520 support, and would putting 2 interfaces into an etherchannel for inside, and 2 for outside work? Reason I ask about that, the inside and outside would connect to 2 different core routers. I would be for an MPLS setup.
View 5 Replies
View Related
Sep 15, 2010
Recently we've been receiving the following log entries on our WLC 4402. Unfortunately Cisco's documentation is less than useful as to what this message means or what could be causing it. [code]
View 9 Replies
View Related
Nov 5, 2012
I'm configuring AIR-CAP2602I-E-K9 out of the box, literally, and I want to configure it with a static address. I paste in the following commands. [code]After the host name line is pasted in I get "ERROR!!! Command is disabled" but the rest of the commands are accepted. I do a sh capwap ip config and the get the output below which looks like that config has been taken but why not my hostname? [code] I know or hoping that the APs will contact the wireless controller since I've the ip in there for it. It just means I'll be renaming all the APs, all 18 of them!
View 6 Replies
View Related
Dec 28, 2011
Currently Being Moderated Wireless users getting disabled
View 6 Replies
View Related
Jun 28, 2012
ASA 5520
version 8.2
My client has the inside network on interface gig0/1.100 and the guest network on gig0/2.200. The whole 10.77.1.0/24 network needs to be able to reach the server with IP 10.47.47.80 using HTTP. The access list is in place ont the guest interface to allow traffic to the server. The problem is that when I do a packet trace to see the traffic flow, it is dropped on a NAT rpf-check. NAT control is disabled. [code]
View 2 Replies
View Related
May 31, 2010
the " password recovery functionality is disabled " service is running on the system .
im trying to access rommon in a Cisco 851, with not much success, i am sending a break after the image is loaded ( in the time frame that is allowed for that) .
View 13 Replies
View Related
Oct 9, 2012
[URL]
This router support bridge mode, but i'm unable to configure it. There's no such option in the web configuration page, but the manual says that disabling nat activates automatic routing mode. Unfortunately all i get when i disable nat is to be unable to reach any wan address.
By watching the generated routing table on the wrp400 (when in NO nat mode) i see that 0.0.0.0 is correctly set up to use the external border router, but any incoming packet from the wrp400 lan port isn't routed there.
Also, i don't get any dhcp from the external router, this means the wrp400 is blocking it.
how to set up a bridge mode between wan and lan ports
View 1 Replies
View Related
Apr 15, 2013
I am using Windows 7, suddenly my network adapter has been deleted and i am unable to use Internet
View 7 Replies
View Related
Jan 28, 2011
I tryed going into bios and disabled it and reabled it still its not working, tryed to uninstall it and reinstalled it still not working
View 1 Replies
View Related
Apr 15, 2011
I seem to be having the same media disabled message in Vista. How do I proceed with this type of refresher in Vista? Out of the blue, no networks can be detected on this particular laptop. I have tried uninstalling the HP WLAN program so far.
View 5 Replies
View Related
Mar 28, 2011
About 5 days ago the computer crashed. I was able to reload Windows XP and load all the drivers and hardware. The only problem is, now the WLAN is saying that it is disabled and I am unable to enable it. The stupid thing about this is, when the computer crashed, the next day i was able to get on. The WLAN was working just fine and so I decided to go ahead and load windows anyways because it has been having issues. Every since I did that, the WLAN has been disabled.
View 10 Replies
View Related
Feb 16, 2013
I have a westell DSL modem/router supplied by Frontier. It connects only to the telephone line and via cat5 to my main router, a cisco EA6500. Everything seems to be working fine, I just would like to understand a few things.I disabled wireless radio on the westell, enabled it on the cisco, so I have just one WIFI network active.I know I am not supposed to have two DHCP servers active, but I did not know how else to be sure the CISCO would get a good address, so I left DHCP active on the WESTELL, and also enabled it on the CISCO to provide service for the rest of the net.The WESTELL admin interface is at 192.168.1.1, and assigns addresses in this range.According to the WESTELL, the CISCO is at 192.168.1.27, which I assume was assigned by DHCP.The CISCO has an admin interface at 10.144.224.224, and assigns addresses in this range to all the other devices on my net.As I say, everything works.I can access both router admin pages with a browser on my main 10.144.224 network, and can ping both.But I don't understand why it works.What rules allow me to talk to the WESTELL admin page from the CISCO private network, but do NOT propagate the DHCP access which is at the exact same IP address.
It is great that it works. But should I really have disabled DHCP on the WESTELL and assigned a static address to the CISCO? Or is this situation actually provided for in the rules, not just a lucky accident that it works?Why does the scanner say that the CISCO DHCP is "Unknown" rather than Authorized or Unauthorized? Is there something I can or should do to get it to be "Authorized"? I can ping 192.168.1.1, but not the 192.168.1.27 (times out), and yet when I ping a non-existent 192.169.1.3 I get "Reply from 192.168.1.27: Destination host unreachable".
View 4 Replies
View Related
Jan 22, 2012
Iam unable to share my internet connection.I am unable to use it on a router even.When i connect it to my laptops Ethernet port its working fine.But when i connect it via router its just showing internet access but i m unable to open any pages.
View 1 Replies
View Related
Mar 4, 2013
I kinda accidentally disabled our internet network and I can't find a way to reconnect it with our adapter. I tried to troubleshoot it and also search for our device, and nothing seems to work.
View 8 Replies
View Related
Feb 22, 2012
LAN connection gets disabled by itself on idle. Sometimes BSODs.A few days ago I tried connecting a MBlaze modem to my laptop (Windows 7 Ultimate 32 bit) to access internet. But it resulted in instant BSOD everytime.I deleted the modem software after that & didn't try to connect it again.But now, whenever I connect using my LAN broadband, connection works fine as long as I am continuously browsing something. But as soon as I stop browsing and it goes in idle mode in about 10-15 minutes, the connection gets disconnected. In the adapter properties, it shows that the driver is working properly. If I try to disable or uninstall it it doesn't give a response. The only solution to this is a forced shutdown & restart, after which it works fine untill not idle. I am not able to download anything because of this.I tried many things like reinstalling the network adapter driver, unchecking the power management feature, resetting the connection, etc. but nothing is working.
View 5 Replies
View Related
Apr 17, 2011
my laptop can't connect to a wireless network, so I have to keep it in one room connected to the modem. When I unplug it, even with the wireless switch on, it loses the connection. When I use ConfigFree, it says the wireless network device is disabled. I went to device manager and updated the driver for the network adapter, and it still said it was disabled. What should I do now?
View 6 Replies
View Related
Sep 20, 2011
My pc is connected to a server that has internet access, but they are blocking the internet on me?
View 3 Replies
View Related
May 18, 2011
problem is my brother has been playing with its config page. he changed the IP Address of the modem and disabled DHCP. he forgot what IP Address he inputted on the config page. I tried resetting the router with the small button on its side. Nothing happens. all the lights blink when i pushed the reset button for 10 sec. but nothing happens. i still can't access its default IP which is 192.168.1.1 IS there anyway to determine its IP Address even if DHCP is disabled ?
View 5 Replies
View Related
Sep 26, 2012
I connected AP 1522 to AC power source and this is the message that i received on the console port.
%CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (0000.0000.0000)
Why this message apear ?This is not sufficient power to bring up radio interfaces?
View 5 Replies
View Related
