regarding device package for Cisco MCS 7835-I3 [Cisco 7800 Series Media Convergence Servers] . I have added Call manager in LMS 3.2.1 but showing ? as there is no device package installed in LMS.
View 2 Replies
I would like to use the Cisco ATA 186 as a SIP device with Cisco Call Manager 7. However, I have found that the SIP firmware for the Cisco ATA 186 is unsupported by Call Manager 7.Therefore, In order to use the ATA as a SIP device with the Call Manager, I believe I will need setup the ATA as a 3rd Party SIP device by doing the following:
1. Disable the TFTP option within the ATA, so that the SIP firmware is not overwritten by firmware from the TFTP server.
2. Install the 3.2.1 SIP firmware on the ATA, since the ATA is currently running the 3.2.4 SCCP firmware.
3. Register the ATA, as a third-party SIP device, with the Call Manager .Should I register the ATA as a 3rd party device?
I tried to discovery WS-C4507R+E devices with lms 4.0 but the devices result unknown, any package to install to discover these types of device?
View 1 Replies View Relatedwe are running callManager 7.1 (user accounts are tied to AD)... one night our call manager got rebooted by IT. upon reboot, CM failed over to the Subscriber node. Some how IT got Callmanger back over to the Publisher node.....No now of us can log into CallManager using our AD accounts...
View 2 Replies View RelatedI have installed LMS 4.1 and discover all the devices (router/switches) but i want to show IP Phone on the LMS. I am unable to discover call manager in LMS 4.1 topology.
In Call Manager 8.6 in Cisco Serviceability under snmp setting i have enable the read community string and check snmp, MIB service are running.AM i using the correct proecdure. How can i get the Call Manager on LMS server so that i can see IP phones on LMS topology. 8.6 is installed on VM Ware.
I setup one network where LMS is in subnet 192.168.5.0/24 and CUCM is in subnet 192.168.1.0/24. both are reachabe to each other and both are also in different EVN/VRF. when i try to discover the CUCM from LMS 4.1. It discover only routers and switches. I am unable to find any CUCM 8.6 server, i did the snmp read community setting in call manager under serviceability.
In addition, IP phones are appeared as END host not as IP Phones. (find attached image)
create a hunt group for the people on call. I have plane this below configuration so far, and I would like to associate the cisco ip phone number with the personal mobile.
1) how can I associate the office number with the mobile one?
2)how and where I set up the forward no answer?
1) Create a line group, and add lines according to the user that we have in the group. Set the Distribution Algorithm to Circular.[URL] I need to create 1 line group per each user. Step to create a line
a)Choose Call Routing > Route/Hunt > Line Group
b)To add a new line group, click the Add New button
c)n the Line Group Configuration window that displays, enter a name in the Line Group Name field. The name can contain up to 50 alphanumeric characters and can contain any combination of spaces,
periods (.), hyphens (-), and underscore characters (_). Ensure that each line group name is unique to the route plan.
d)Choose the appropriate settings as described in Table 36-1. Table link ( http://www.cisco.com/en/US/docs/voice_i ... #wp1053560 )
e)To add or update this line group, click Save.
2) Create a hunt list, and add the line group Step to create a hunt list
a)Choose Call Routing > Route/Hunt > Hunt List.
b)Click Add new
c)In the Hunt List Name field, enter a name. The name can comprise up to 50 alphanumeric characters and can contain any combination of spaces, periods (.), hyphens (-), and underscore characters (_). Ensure each hunt list name is unique to the route plan.
d)In the Hunt List Name field, enter a name. The name can comprise up to 50 alphanumeric characters and can contain any combination of spaces, periods (.), hyphens (-), and underscore characters (_). Ensure each hunt list name is unique to the route plan.
e)To add this hunt list, click save
f)The system checks the Enable this Hunt List check box by default for the new hunt list.
g)Add at least one line group to the new hunt list.Adding Line Groups to a Hunt List (Associate a line group to hunt group)
a)Choose Call Routing > Route/Hunt > Hunt List.
b)Locate the hunt list to which you want to add a line group
c)To add a line group, click Add Line Group.The Hunt List Detail Configuration window displays.
d)From the Line Group drop-down list box, choose a line group to add to the hunt list.
e)To add the line group, click Save.The line group name displays in the Hunt List Details list on the left side of the window.
f)To add more line groups to this list, click Add Line Group and repeat Step c through Step e.
h)Click save and then to click reset to reset the hunt list. When the popup windows display, click OK.
I have CUCM 8.5 in a lab environment that connects to a Cisco 2801 which has a VIC2 FXO card on board, I have believe that I have configured the MGCP correctly and also configured my CUCM correctly but I'm just getting a fast busy when I make a call through the PSTN, I have tried removing the Ethernet cable from the Router just to test what happens when I dial external and again I get fast bust.
Here is my configuration setting: -
From CUCM gateway details:
Gateway Name MGCP
Protocol MGCP
AALN/S0/SU1/0@MGCP
AALN/S0/SU1/1@MGCP
AALN/S0/SU1/2@MGCP
AALN/S0/SU1/3@MGCP
[code]....
I'm trying to install the anyconnect package on an ASA 5510 running version 9.0.1. I'm getting the following error:
labfwpix(config-webvpn)#anyconnect image disk0:/anyconnect-win-3.1.01065-k9.pkg
copying 'disk0:/anyconnect-win-3.1.01065-k9.pkg' to a temporary ramfs file failed
Is there something that I'm doing wrong when installing the package?Also, is there away to manually install the client on a stand alone PC without a deploying method, similar to the IPSEC client software?
I'm using a CISCO1921/K9 with IOS 15.1(3)T1 and licensed fetaures ipbasek9, securityk9, datak9, SSL_VPN. After a working setup of webvpn I'm running in troubles after a reload - of course, the running-config is copied before reload ; )
This config line: webvpn install svc usbflash0:/webvpn/anyconnect-win-2.5.3055-k9.pkg sequence 1
is missing after a reload. Consequence: the "Anyconnect Client" refuses to connect. What can be the reason? Is it the sequence "1" - I only have one sequence and not more of them? I use this CLI input
webvpn install svc flash:/anyconnect-win-2.5.3055-k9.pkg sequence 1
to install - the line above appears in the running-config output - is this the right way?
Does WLC 4400 is supported in LMS 4.1 in CiscoView.
When I check device update in admin-system-software center. I don't see any available package for the WLC 4400.
I have added manually the cisco asa 5520 to lms 4.2 , because automatically the lms didn't discover it ,however when i tried to open the device using cisco.MessageCannot find applicable device package for 192.168.100.100This error could be due to one of the following:- The device package for this device type is not installed.- Device support for this device type is not available.- You are trying to open a component inside a device.To correct the problem, either install a device package for the device type, or open the parent device to manage the component.
View 1 Replies View RelatedI have a trouble with Cisco view 6.1.8. I had update offline device package because i don't have internet . When i connect to switch router 3945 and switch 3750, router 2911 on Cisco view then I receive "cannot find applicable device package for 10.1.241.10". Need to reinstall device package. The version of Cisco work LMS is 3.2. I check Active log and receive message .
The Package(s) Selected for Install :
Cat2960, Cat3750, Rtr2900, Rtr3900, Rtr7000
WARNING : Cat3750(14.0):Consistency check failed for base package DtShare
WARNING : Rtr3900(5.1):Consistency check failed for base package NGMARShare
What is the reason to call a router as data link layer device
View 1 Replies View RelatedI am trying to install Cisco Connect for my E1000 but I get the following error each attempt "An HNAP Call to the device failed for unknown reasons" I've already updated the router to 2.1 version of the Firmware.
Full Details
Error code: 82BD0305Error description: An HNAP call to the device failed for an unknown reason.Model name: unknownModel number: E1000Serial number: unknownFirmware version: unknownOperating system: Windows 7 SP 1Software version: 1.3.11069.2Connection type (WAN): unknownIP address (LAN): unknownIP address (WAN): unknownComputer IP address: 192.168.1.132
We got this software from Cisco and we need to setup this in our network to manage the firewalls.Need to know this software is used to centrally manage the firewalls ?Also how i can i know how to setup this in our network?Assuming this software we will first install on server right? it can be windows server ?Second thing to know is what config changes we have to do on the existing and new ASA so that they can be managed centrally?Also Where i will get the documents that tell me how to setup/install this software?
View 5 Replies View Relatedit was possible to install RSA Authentication Manager server into the ACS 5.3 Virtual Machine ?
View 0 Replies View RelatedI have a XFX Nforce 750a SLI mobo and reinstalled winxp pro and now Im missing the network adapter in device manager. I have a wireless pci card installed and can find that under hidden devices in D manager but no onboard! I do have yellow ? for other devices and yellow ? for everything in there:[CODE]
View 2 Replies View RelatedI was trying to fix a diagnosis error under my Internet Connection stating your computer appears to be correctly configured, but the device or resource (DNS server) is not responding. I thought maybe going to Device Manager while showing hidden files selected then go to non plug and play, and then I deleted NetBT, and then a PC reboot. I was very wrong because I have no Internet, and honestly, I only have one PC.I have Windows 7 Home Premium Anytime Upgrade that I bought. It's a 32-bit OS.
View 7 Replies View RelatedIn my laptop WLAN is showing disabled from Device Manager & no Wireless is showing in the Network Adaptar under Device manager.
View 5 Replies View RelatedI just recently got the internet and I have a desktop computer that has ever rarely been used and it has never had the internet on it. I called tech support of my ISP to see what many be the problem why I can't connect to the internet and found that the source of the problem was I do not have a LAN network connection. When I open Network Connections on the computer, nothing is there. I also went to device manager and there is nothing there for Networking. Under category of "Other Devices" in Device Manager there is a question mark next to "Ethernet Controller". Are there drivers or something I need download to fix this so I can connect to the internet via a DSL connection.
My computer specs are:
Windows XP Professional
Version 2002
Service Pack 2
[Code].....
Next to network adaptors there are yellow marks in my device manager...as follows.
-??(yellow mark) Other devices
-??? (yellow mark) Unknown device
-??? (Yellow mark) Unknown device
i cant find Ports (COM & LPT) in device manager . so how can i change that setting?
View 1 Replies View Relatedthis is a device discovery issue with LMS 3.2. The devices added up in Common Services are not getting reflected under Campus Manager and Device Fault Manager. The devices are manually added and are stack switches (2960S-24TS-L).
View 1 Replies View RelatedI am working with LMS 4.1 and FDM 4.1.0.
If I ask to the Supported Device Finder Portlet about C4503-E (SysObjectId: 1.3.6.1.4.1.9.1.874), it tells that this device is supported by DFM 4.1.0. Nevertheless, in DFM module each one devices appear in the "All Unknown Devices" group, with Error Code: Unsupported. CDP is enable in each one of these devices.
HP computer, was working last friday and today it isnt. Can not connect to the internet or outlook etc. Looked in BIOS says it is conected to LAN - tried enabling and disabling it and re-booting it. Still nothing. Had a tech guy that said to look in device manager, but network adapter was no where to be seen. What shall i try next to resolve this problem?
View 1 Replies View RelatedHave an hp pavilion a1700n with amd athlon. I switched from Vista to XP, but it's not recognizing some drivers. The network card is not detected on my pc, however the device manager says is working properly!!!??? What can I do? I need to connect to the internet in order to download the other drivers.
View 1 Replies View Relatedco worker brought me his comuter to reinstall windows xp, because he did not like vista, he also had his own xp discs, i have done everything like normal, have done this a time or two not my first rodeo with reinstalling windows xp, this is however the first time that this network issue has happened, i have installed the device driver cd as well along with the reset tool from dell's website, im getting NOWHERE.
View 1 Replies View Relatedmy wireless connection suddenley stopped working, the light no longer turns on and the wlan is no longer an option in the vaio smart network folder, its completley disapeared, i can only connect to the net via ethernet cable now
View 4 Replies View RelatedNo network adapter showing in device manager
View 2 Replies View Relatedmy Pavilion dv6 wifi is not working. My In my device manager my Ralink Wifi Adapter is yellow flagged.
View 1 Replies View Related1. I recently purchased an Asus X53-sx1159v laptop (Windows 7 64 bit os - other detals at bottom ).
2. While it has a wifi network connection (which works fine), it doesn't seem to have any listing for ethernet (ie wired) connection. (even though it has the port for wired access.)
3. When i look under computer/device manager/networks, all i get is the wifi atheros 9485 network adaptor. There is no other listing. (see attched file for screen grabs)
4. Am i missing something obvious with all this? The Asus website has examples of this model with screen grab which includes an ethernet adaptor as well (see attached file)
Note that laptop is labelled as an X53 series but in the computer it get listed as a K53e
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz, Intel64 Family 6 Model 42
[Code].....
i've just upgraded my graphic card and now i don't have any network adapters listed in the device manager (only firewire under +IEEE 1394 and all the other devices) I've already reinstalled Windows 7 (64 Bit) and tried installing another LAN card (10/100) - that wasn't recognized.
Within the BIOS (award- Motherboard- GA-P35-DS4 ) i couldn't find anything related that should be turned off/on? [URL]
Could it be broken if it is not appearing there? If yes- why isn't the motherboard recognizing my other LAN Adapter that i've installed on the bottom slot
Should i reset the Bios by pulling the battery/using the cmos jumper?
