Cisco :: Call Manager 8 Not Routing Calls To MGCP?
Oct 5, 2011
I have CUCM 8.5 in a lab environment that connects to a Cisco 2801 which has a VIC2 FXO card on board, I have believe that I have configured the MGCP correctly and also configured my CUCM correctly but I'm just getting a fast busy when I make a call through the PSTN, I have tried removing the Ethernet cable from the Router just to test what happens when I dial external and again I get fast bust.
Here is my configuration setting: -
From CUCM gateway details:
Gateway Name MGCP
Protocol MGCP
AALN/S0/SU1/0@MGCP
AALN/S0/SU1/1@MGCP
AALN/S0/SU1/2@MGCP
AALN/S0/SU1/3@MGCP
[code]....
View 3 Replies
ADVERTISEMENT
May 2, 2012
we are running callManager 7.1 (user accounts are tied to AD)... one night our call manager got rebooted by IT. upon reboot, CM failed over to the Subscriber node. Some how IT got Callmanger back over to the Publisher node.....No now of us can log into CallManager using our AD accounts...
View 2 Replies
View Related
Jul 30, 2012
I would like to use the Cisco ATA 186 as a SIP device with Cisco Call Manager 7. However, I have found that the SIP firmware for the Cisco ATA 186 is unsupported by Call Manager 7.Therefore, In order to use the ATA as a SIP device with the Call Manager, I believe I will need setup the ATA as a 3rd Party SIP device by doing the following:
1. Disable the TFTP option within the ATA, so that the SIP firmware is not overwritten by firmware from the TFTP server.
2. Install the 3.2.1 SIP firmware on the ATA, since the ATA is currently running the 3.2.4 SCCP firmware.
3. Register the ATA, as a third-party SIP device, with the Call Manager .Should I register the ATA as a 3rd party device?
View 2 Replies
View Related
Jul 29, 2012
I have installed LMS 4.1 and discover all the devices (router/switches) but i want to show IP Phone on the LMS. I am unable to discover call manager in LMS 4.1 topology.
In Call Manager 8.6 in Cisco Serviceability under snmp setting i have enable the read community string and check snmp, MIB service are running.AM i using the correct proecdure. How can i get the Call Manager on LMS server so that i can see IP phones on LMS topology. 8.6 is installed on VM Ware.
View 4 Replies
View Related
Jul 30, 2012
I setup one network where LMS is in subnet 192.168.5.0/24 and CUCM is in subnet 192.168.1.0/24. both are reachabe to each other and both are also in different EVN/VRF. when i try to discover the CUCM from LMS 4.1. It discover only routers and switches. I am unable to find any CUCM 8.6 server, i did the snmp read community setting in call manager under serviceability.
In addition, IP phones are appeared as END host not as IP Phones. (find attached image)
View 6 Replies
View Related
Mar 28, 2012
create a hunt group for the people on call. I have plane this below configuration so far, and I would like to associate the cisco ip phone number with the personal mobile.
1) how can I associate the office number with the mobile one?
2)how and where I set up the forward no answer?
1) Create a line group, and add lines according to the user that we have in the group. Set the Distribution Algorithm to Circular.[URL] I need to create 1 line group per each user. Step to create a line
a)Choose Call Routing > Route/Hunt > Line Group
b)To add a new line group, click the Add New button
c)n the Line Group Configuration window that displays, enter a name in the Line Group Name field. The name can contain up to 50 alphanumeric characters and can contain any combination of spaces,
periods (.), hyphens (-), and underscore characters (_). Ensure that each line group name is unique to the route plan.
d)Choose the appropriate settings as described in Table 36-1. Table link ( http://www.cisco.com/en/US/docs/voice_i ... #wp1053560 )
e)To add or update this line group, click Save.
2) Create a hunt list, and add the line group Step to create a hunt list
a)Choose Call Routing > Route/Hunt > Hunt List.
b)Click Add new
c)In the Hunt List Name field, enter a name. The name can comprise up to 50 alphanumeric characters and can contain any combination of spaces, periods (.), hyphens (-), and underscore characters (_). Ensure each hunt list name is unique to the route plan.
d)In the Hunt List Name field, enter a name. The name can comprise up to 50 alphanumeric characters and can contain any combination of spaces, periods (.), hyphens (-), and underscore characters (_). Ensure each hunt list name is unique to the route plan.
e)To add this hunt list, click save
f)The system checks the Enable this Hunt List check box by default for the new hunt list.
g)Add at least one line group to the new hunt list.Adding Line Groups to a Hunt List (Associate a line group to hunt group)
a)Choose Call Routing > Route/Hunt > Hunt List.
b)Locate the hunt list to which you want to add a line group
c)To add a line group, click Add Line Group.The Hunt List Detail Configuration window displays.
d)From the Line Group drop-down list box, choose a line group to add to the hunt list.
e)To add the line group, click Save.The line group name displays in the Hunt List Details list on the left side of the window.
f)To add more line groups to this list, click Add Line Group and repeat Step c through Step e.
h)Click save and then to click reset to reset the hunt list. When the popup windows display, click OK.
View 2 Replies
View Related
Mar 27, 2012
regarding device package for Cisco MCS 7835-I3 [Cisco 7800 Series Media Convergence Servers] . I have added Call manager in LMS 3.2.1 but showing ? as there is no device package installed in LMS.
View 2 Replies
View Related
Jan 4, 2012
Wireless Phone --> 881W router --> VPN --> ASA5510 --> LAN with CCM and Voice Gateway
Phone registers to CCM Internal calls work External calls connect but get no voice in either direction
View 13 Replies
View Related
Jun 25, 2012
I'm trying to install a Gateway in Red Hat Linux to Cisco Smart Call Home Service, and reading about this in google, i find this info:Smart Call Home on the ASA This is much more simply to configure and operate.I want to know what solution is more recomended and why.
View 1 Replies
View Related
May 12, 2012
Customer is running LMS 2.6.Scheduled backup was running perfect. But it is no more happening.When we checked we found that the "License Manager/ Deamon Manager is down" message pop ups.
We reset the casuser password, and then restarted the services. It becomes ok.But only the immediate backup is successful. Scheduled task fails for all those devices."License Manager/ Deamon Manager is down" happens quite often.
View 1 Replies
View Related
Jul 12, 2012
I have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. I already try to debug this with debug event manager action mail but didn't see any output. [code]
View 2 Replies
View Related
Feb 9, 2011
We have 2 h323 IP phones (non cisco) that connect to an IP PBX via a VPN connection using PIX 5505's at each end. The VPN seems to work fine and the phones can be used normally with good call quality, display, status...The problem is that when talking on the phones for any extended period of time, the phone reboots, drops the call and then restarts automatically. This problem usually happens on phone calls lasting 20 minutes or more but has happened on calls as short as 15 minutes. I have also made calls which have gone 45 minutes before the reboot. I have removed everything from the network hosting the remote IP phones except for a single phone and the problem still occurs. It is not a POE Issue as the phones can use a power brick and it still happens. The same phones work perfectly on-site when not using the VPN.Someone has mentioned that I should adjust the UDP Timout Timers of the VPN. I don't see any UDP timers and am at a complete loss on what is causing this. The data traffic does not seem to get dropped when connected accross the VPN for hours at a time.
View 1 Replies
View Related
Mar 16, 2012
I start to use the CM. I received a request to block a number,I need to block the call only on the Call Manager or also on the Gateway that I have?
View 6 Replies
View Related
Jan 24, 2011
I am encountering delays when making any calls using VOIP. I understand that there is always a delay using VOIP but not as much. I've done a bandwidth test on my network and everything seems to be Ok, we have 4 T1s with 55 Reps using it. There is nothing choking up the network.
View 3 Replies
View Related
Aug 29, 2011
Can I get a modem that calls using analog and once it reaches my ISP it converts to 64K?
View 1 Replies
View Related
May 1, 2011
As stated in the attached picture, my company has a remote office which its PBX was connected to the main PBX via a pair of leased lines and a pair of E1/HDSL converters. (The distance is about 2 kilometers, so the E1 was converted to HDSL and then back to E1 at the remote site)
Now, IP network is developed between two sites.We want to transfer the calls via a pair of 2811 Routers, both equipped with VWIC2-1MFT-T1/E1, as the second part of the picture. I tried to find an straightforward document, but I was unsuccessful.What configurations should be made at both ends to transfer the calls to/from the remote site ?
View 19 Replies
View Related
Nov 8, 2012
I have programmed two E1 ports on Cisco 2811, one for E1-PRI and other for CAS. My running-config is as below
controller E1 0/0/0
framing NO-CRC4
clock source internal
ds0-group 1 timeslots 1-15,17-30 type r2-digital dtmf dnis
[code]....
I have made 4 as trunk group access on the PBX for E1-PRI and 8 as trunk group access for E1-CAS.I am able to dial 4-1-6261 to place calls on telephone 6261 from 6000(outgoing and incoming over PRI). And I am able to dial 4-2-6261 to place calls on telephone 6261 from 6000(outgoing on PRI and incoming on CAS).But I am not able to dial out from my PBX extensions over the E1-CAS card using 8-1-xxxx or 8-2-xxxx. I have patched two PBXs back to back on their E1-CAS ports and am able to dial out using 8-xxxx. So this means the trunk group allocation on PBX is working fine. The show controller e1 0/0/0 is showing normal stats.When I do a show voice port 0/0/0:1 I see that one of the ds0 timeslots are being seized when I try to dial out on 8-x-xxxx but the Out Status column entry against the timeslot says clear_bak.When I am placing calls on PRI, I don't see any such indication against the timeslot being seized.Basically since I am able to dial in to my E1-CAS port, the line coding, framing, signaling(to some extent) must be right, or so I guess. But am not able to dial out.
View 1 Replies
View Related
Jun 12, 2011
What is the maximum possible ISDN calls on Cisco 7206VXR router using PRI links and PRI supported cards.
View 7 Replies
View Related
Apr 5, 2012
in our office private network we are using a proxy server for internet connection sharing, we are unable to make voip calls through this proxy server?
View 1 Replies
View Related
Dec 1, 2012
I'm a new user of VOIP. My network connect is Cable modem -> router (Dir 615) -> ATA (SPA122) . Outbound calls have no problem. But inbound calls sometimes work, sometimes not ( got message: not in service)
View 1 Replies
View Related
Apr 8, 2011
I have the latest Firmware version 2.05NA on the DIR-825 and while I can make outbound SIP calls I can't receive any inbound calls. The phone will ring but I can't pick-up the call. [code] I am at a loss as to how to register my phone. When I uncheck ALG SIP the phone will not register to my server.I have a Polycom 550 connected to a Trixbox server. The prior router worked great.
View 6 Replies
View Related
Jun 28, 2012
I have a telephony system already in place with 6 FXO active ports configured on a 2821 Router.The thing is that I am not able to make an ip phone forward calls to a mobile No.I can make calls to the same mobile number when dialed from the phone but the call routing seems not to function correctly when call-forward all is configured on the ephone-dn.I would like to focus only on voice-port 0/0/0 and 0/0/1?
voice-port 0/0/0
supervisory disconnect anytone
output attenuation -3
echo-cancel coverage 32
compand-type a-law
cptone GB
[code]....
View 3 Replies
View Related
Dec 16, 2011
I have a 887 setup as a EasyVPN server, and a 861 as an EasyVPN remote - network extension mode with split tunnelling.This works fine - I can ping and connect to machines across the tunnel.However if I setup a VOIP handset to connect across the tunnel it registers and calls work, but drop after 30secs....I know this is normally a firewall or nat problem, are easyvpns firewalled or natted?
View 9 Replies
View Related
Apr 9, 2013
I heard from customers calling into the office stating that they have experienced some issues with our prompts and the extension input, that it is not recognizing their input. Stating sometimes it does not work on their land line but once they call back on their cell phone it works. We in the office all had people from the outside call from a land line to our office to verify the issue but the calls went through. We are thinking that they may be dialing the wrong extensions.Has anyone had any issues with land lines having trouble calling in.I am running cucme connected to a sip trunk.
View 4 Replies
View Related
Dec 6, 2012
Have a asterix PBX running my system and I upgraded my security with a cisco ASA 5505. Now all the extensions are working including the remote once. Everything elase like internet.Other servers all working fine. Only problem is that when ever someone dials a landline number from an extension it does not go through.seems like the firewall is blocking it but I cannot figure out why or how. All the NAT and Access list is fine. Although I have no idea how to accept the SIP PROXY IP through the firewall and I am guessing that might be the problem. There is no any other problem and I am 100% satisfied with the ASA5505 except this problem
View 3 Replies
View Related
Nov 8, 2012
I have an SA520 that is being used as a front end firewall. Behind it I have an IP PBX. The VOIP provides are registered and I can make outgoing calls. However It appears that the SA520 is either blocking or not routing the calls. I have opened the ports recommended by both the IP PBX and the VOIP provider. What do I need to do to make incoming calls through the SA520?
View 1 Replies
View Related
Oct 24, 2011
We're having some numbers ported over to us and we'd like to verify that we are in fact receiving all of the numbers at our SIP gateway. Since we have been getting more and more activity on this router, I'm becoming more concerned about using certain debug's for fear that the router maxes out CPU and drops.
What the best debug command would give me this information with minimal impact on CPU? In the past I've used 'debug ccapi inout' and a couple of others similar to that. With so much activity though sometimes it bombs the router. Also I am logging to the console directly, maybe there is a better method with less CPU impact. I just don't want to have to go back and forth to look for stuff 50 times either if I write out to a file or something, it could work though I suppose.
View 1 Replies
View Related
Mar 28, 2012
I'm in charge of the IT of a dorm with 200 inhabitants. A lot of people complain about the bad quality of "skype-calls". Audio is delayed and video stucks. The actual speed of our internet connection should be fast enough so I guess it has something to do with the QOS setting. I checked it on our WLC 3750 and right now we use Silver (best effort). Could there be any improvement when I set it to Platinum?
View 15 Replies
View Related
Jan 5, 2011
We have a Cisco Router 3825 which we use to convert phone calls from PSTN to SIP.Can any one suggest us (or point to a documentation) as to how can we use this router as a load balancer (to balance load among different SIP terminals) ?
View 3 Replies
View Related
Jun 20, 2011
I know the problem lies in the timeout for the default inspection rules. I cannot find where to change this.I have nat statements for 1 to 1 nat to my polycom and tandberg video devices. I have set the firewall for the ouside to in rules to inspect all. This allows the devices to communicate with public addresses, but the video calls drop after 1 hour. How do I change the settings so this does not happen. I have tried setting the rule to allow instead of inspect, but when I do this, I have no access at all. I just want to nat 1 to 1 and allow all traffic to the nated devices. I know this is not secure but it is the only way to allow h323 through to let the video conferencing devices work.
View 1 Replies
View Related
Aug 3, 2011
i use my sim card in modem connected to pc to surf. is it possible to receive calls as i surf through this sim card?
View 1 Replies
View Related
Jan 30, 2013
About 2 years ago I bought my first laptop and the person I was with recommended my purchasing of a Belkin router. I bought the router, it worked great until this past summer when suddenly whenever somebody called my house phone, my connection was dropped. I was angry cause naturally I have those family members that want to call and talk on the phone with my mother for hours. Eventually I figured out I could work about the problem by hooking the Ethernet cord on my Westel directly to my laptop. Its a temporary fix though in my opinion because this requires me having to sit on the floor against my bed room door and this isn't comfortable, not to mention its also confining, I miss walking around the house with my laptop. Anyway this past weekend I decided to try buying a new Belking N300. This however didn't solve the problem, I still got my signal dropped whenever somebody called the house.
View 14 Replies
View Related
Jun 19, 2011
I have a D link 655 wireless router and my magic jack calls end after 15 seconds.
View 2 Replies
View Related
