%ASA-3-305005: No translation group found for tcp src inside:211.155.169.186/1433 dst outside:42.121.87.89/6000, I found this error ,but the IP 211.155.169.186 is public address. I check the configuration but didn't find any information about this address.I don't understand why src is inside? How can I solve this error?
View 1 Replies
provide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View Relatedi am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View RelatedWhen the following was issued:
ip wccp 0 redirect-list wccp_acl group-list 10 password 0 ourpassword
Received this error:
MDT: %COMMON_FIB-3-FIBIDBINCONS2: An internal software error occurred. WCCP:0 linked to wrong idb Loopback0 (xyz node name)
When the following was issued 10 minutes later:
ip wccp 70 redirect-list wccp_acl group-list 10 password 0 ourpassword
No error msg (but now wccp was active)WCCP appears to be working but we are ** having problems connecting ** with our websense (7.6) box via GRE.Websense is connected to the 6509 which is connected this 3750 switch.
a Customer ask me to configure a etherchannel between two Switches C3500 XL Version IOS 12.0 follow the first configuration what I done and the output error show me by switch:
Sw01(conf)# interface port-channel 1 % invalid input detected at '^' marker.
I have to do something before add an new port-channel interface ?? why the Sw01 does not accept my configuration ?
McAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies View RelatedI am currently migrating a netscreen firewall to a asa 5515 version 8.6 The issue is setting up the management connectivity.
basically the management IP of the cisco asa is not advertised. But, we want to route a management IP through the management interface to interface Gi0/2.
so IP of management interface is say - 216.10.100.10. and the IP of the inside interface is say - 198.1.1.10/24 on our router we have a static route sending 198.1.1.0/24 to next hop of 216.10.100.10 (management interface of cisco asa).
On the Cisco ASA can I send the traffic to the inside interface and manage the firewall via ssh that way?
I'm trying to install an ASA 5510 transparent firewall using ASA version 8.4(3)9 but I don't understand how traffic will ever pass through my firewall if both interfaces are on the same sub net(V lan) as the host and it's default gateway? The reason I'm doing this is were installing UAG (or Direct Access) and the UAG appliance need to have public IP's but still be behind a firewall (see attached diagram).
Looking at the documentation (which all seems to be for 5505's running 8.2) it almost seems like i need to have the transparent firewall 'in-line' to the ISP router?, but this router services another IP address range on another v lan for other (routed) firewalls (not shown on diagram) so putting it 'in-line' is not possible. Surely this can't be the case can it? If not how is it supposed to be cabled up and configured so packets go through the firewall?
How are asa5540 in high availability mode upgraded for their versions.
View 1 Replies View Relatedconfiguring NAT on intranet firewall. here is the my topology:
DMZ Network - - - - - - - - - External Firewall - - - - - - - - - Internet
|
|
|
Internal Network - - - - - - - - - Internal Firewall
1) I can Ping the intneral host from external firewall, internet firewall and DMZ network
2) Both ASA's are running OS Version 9.0(1)
3) ACL used permit IP any any, on both (i.e inside and outside)
NAT configuration on Internal Firewall (Identity NAT)
object network MGMT-SRV-INSIDE subnet 10.10.10.0 255.255.255.192
object network MGMT-SRV-identity
subnet10.10.10.0 255.255.255.192
object network MGMT-SRV-INSIDE nat (Inside,Outside) static MGMT-SRV-identity
[code]....
I would like to know how can I block a ip address from the CLI at the Cisco PIX Firewall Version 6.3(4)
View 4 Replies View RelatedI would like to know whether CSM 4.3 is compatible with ASA version 9.1(1). Any appropriate url that contains information about these two version's compatibility?
View 2 Replies View RelatedI try to convert a CISCO ASA 8.2 version to 8.4 BUT, I have a small or "little" problem :On Cisco ASA 8.2.x, i have a possibility to create multi-line global with different subnet.Example :
global (outside) 2 217.1.x.65-217.x.x.66 netmask 255.255.255.240
global (outside) 1 interface <-- Ip interface is other subnet : 217.3.x.3
global (outside) 2 217.1.x.67 netmask 255.255.255.240
nat (inside) 1 0.0.0.0 0.0.0.0
nat (dmz2) 2 192.168.4.0 255.255.255.0
What is the method or solution to translate multi-global in 8.4 ? with static translation in 8.4 : i try to use different server in inside's zone, but not in same network on outside. In 8.2 Firmware, it's very easy to use that, but in 8.3-8.4 version, i don't have some idea to manipulate ...
interface Vlan1
description Lien vers reseau Interne Client
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0
[code]....
We want to make an upgrade of one of our customers' ASA 5520 (with failover). They have version 8.2 now and we want to get the more stable newest one. Can we get an 8.6 version? or we need an ASA 5500X for that one?
View 2 Replies View RelatedWe have 2 firewalls on PIX facing the Internet and connected to interface e1 (behind it) an ASA version 8.3 Both the PIX (Firewall facing) and the ASA are on the same subnet.
By using Routing statements and statics I have been able to reroute specific traffic to the ASA5520 version 8.3 Now I need to inverse the 2 devices. The ASA5520 will be facing the Internet and the PIX will be behind it.Unfortunately the ASA5520 is refusing to route the traffic to the PIX. The access-lists are open accordingly and a NAT on the ASA has been created.
what the new command is for NAT in version 8.3?The config i have is from Version 7.2 and doesnt work on 8.3. [code]
View 12 Replies View Relatedhow to configure ip sla monitoring on asa ver 7.0 (6) ?
View 4 Replies View RelatedI try to setting up a PIX firewall to server as firewall end point for a small network for Internet access. I had include PIX configuration setup, I had replaced IP address information by sentence which describe them since IP Address is sensitive information in our network.
For some reason NAT process doesn't work in log I always receiving this kind of messages :
106011: Deny inbound (No xlate) tcp src inside:INTERNAL_HOST_IP/2490 dst inside:HOST_PUBLIC_INTERNET_IP/80
106011: Deny inbound (No xlate) tcp src inside:INTERNAL_HOST_IP/2490 dst inside:HOST_PUBLIC_INTERNET_IP/80
106011: Deny inbound (No xlate) tcp src inside:INTERNAL_HOST_IP/2491 dst inside:HOST_PUBLIC_INTERNET_IP/80PIX Configuration
[code]...
I need to fullfill the below configuration which is working fine on my actual D-Link Netdefend firewall.
We have a range of IP assign by our ISP : 194.250.47.128/29
194.250.47.129 is the firewall IP and 134 the isp gateway.
We have 4 interfaces
- The local user interface: lan =192.168.170.1/24
- The servers interface : dmz =192.168.171.1/24
- The database interface : oracle=192.168.169.1/24
[Code]...
I have PIX515 with version 7.0 installed, so can i install version 8.3 on it?and what will be the memory requirements?
View 2 Replies View RelatedI have to test new Cisco ASA's IOS version 8.4 in my GNS3 LAB . do provide the link for downloading the same.I dont have direct download access from cisco.com.
View 1 Replies View RelatedWhat anyconnect version do I need on a 5505 so i can have people connect via iOS devices? Right now I have "anyconnect-macosx-i386-2.5.1025-k9.pkg" on there, will that work for iOS devices?
View 7 Replies View RelatedI have a PIX506E that was resently reset and it has version PIX Version 7.1(2) . It either uses some different commands or I am not using them correctly. [code]
View 2 Replies View RelatedI was wondering if I picked up a used (End of Life) pix-515e, would would I need to do to be able to upgrade it to that latest version of IOS made for that product? Is it still possible to even get access to that version? Will cisco allow downloads for that devices IOS?
View 4 Replies View RelatedI just need to upgrade existing FWSM of 6509.FWSM Firewall Version 2.3(1)is it possible to upgrade to the version of 4.X .If not to which version is safe?And also I need to steps of doing FWSM upgrade.
View 1 Replies View RelatedASA 5505 Version 8.2 or older nat (inside) 1 10.0.0.0 255.255.255.0nat (INTF4) 1 10.0.4.0 255.255.255.0nat (INTF5) 1 10.0.5.0 255.255.255.0nat (INTF6) 1 10.0.6.0 255.255.255.0nat (INTF7) 1 10.0.7.0 255.255.255.0global (outside) 1 209.165.200.235-209.165.200.254 netmask 255.255.255.224global (outside) 1 interface
I believe this setup does the following. The inside interface and interfaces 4,5,6,and 7 will translate using this line....
global (outside) 1 209.165.200.235-209.165.200.254 netmask 255.255.255.224
and if the addresses run out is will start using the ouside interface IP address to translate, so traffic is not disrupted and is based on the line of configuration.....
global (outside) 1 interface
My question, does it do this because of the order of the configuration..
global (outside) 1 209.165.200.235-209.165.200.254 netmask 255.255.255.224global (outside) 1 interface
or would it do it that way even if it was like this?
global (outside) 1 interfaceglobal (outside) 1 209.165.200.235-209.165.200.254 netmask 255.255.255.224
and if so why?Now let's convert the above configuration to ASA 5505 Version 8.3 or newer.
object network OUTSIDE-NAT-POOLrange 209.165.200.235 209.165.200.254object network INTERNAL-SEGMENTSsubnet 10.0.0.0 255.255.248.0nat (any,outside) dynamic OUTSIDE-NAT-POOL interface
My question is how does it know to use the outside interface as a backup when the OUTSIDE-NAT-POOL is depleted?Also why do I need to define the INTERNAL-SEGMENTS ? Doesn't the "any" in the (any,outside) take care of that?Also wouldn't the "any" in (any,outside) cover interface 3 or DMZ which could be an issue?
Will give configuration of NAT for my internal users with 192.168.1.0/24 with single public IP.
I new to configure IOS version 8.3.
im changing the firewall 5510 to 5515, with ASA5510 the incoming and outgoing calls work perfectly, but when i active the 5515 the outgoing calls doesnt work, only the incoming calls work.
As you see on the topology,the flow of calls happens this way:
In the outgoing calls the phone forward the call to the PABX(172.17.3.4), and the PABX forward the call through the ISP LINK to SIP SERVER (10.140.131.208). The incoming calls occur in the reverse path.
ASA 5510 config:
ASA Version 7.0(8)
name 172.17.3.4 PABX
dns-guard
!
!
interface Ethernet0/1
[Code]...
Im changing the firewall 5510 to 5515, with ASA5510 the incoming and outgoing calls work perfectly, but when i active the 5515 the outgoing calls doesnt work, only the incoming calls work.
As you see on the topology,the flow of calls happens this way: In the outgoing calls the phone forward the call to the PABX(172.17.3.4), and the PABX forward the call through the ISP LINK to SIP SERVER (10.140.131.208). The incoming calls occur in the reverse path.
ASA 5510 config:
ASA Version 7.0(8)
name 172.17.3.4 PABX
dns-guard
!
!
interface Ethernet0/1
description ***ISP SIP Network***
[Code]....
i have asa901-k8.bin" in my asa firewall and downlaod liecnce from cisco,now i dont know how to allow internet to my user.?
View 1 Replies View Relatedhave a question. I have a ASA5510 with IOS version 8.2 . I have my firewall and behind it also have a mail server eg 192.168.1.x. When i send email from inside network it doesn't show as if it's coming grom the out side nated public IP of my server but IP of firewall. What am i missing my example nat statements are . Nat-control is disabled.
static (inside,outside) 196.68.99.x 192.168.1.x netmask 255.255.255.255
access-list inbound extended permit tcp any host 196.68.99.x eq 225
accesslist outbound extended permit host 192.168.1.x host 196.68.99.x
I have a ASA5505 and currently running Version 7.2(4). I was wondering what the latest version of the software would available to me would be.
Here's a show ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
Compiled on Sun 06-Apr-08 13:39 by builders
System image file is "disk0:/asa724-k8.bin"
Config file at boot was "startup-config"
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
I have a requirement to nat two public ip addresses to same interanl ip address. Is this possible on ASA version 9.1?
View 3 Replies View Related
