I need to fullfill the below configuration which is working fine on my actual D-Link Netdefend firewall.
We have a range of IP assign by our ISP : 194.250.47.128/29
194.250.47.129 is the firewall IP and 134 the isp gateway.
We have 4 interfaces
- The local user interface: lan =192.168.170.1/24
- The servers interface : dmz =192.168.171.1/24
- The database interface : oracle=192.168.169.1/24
[Code]...
What anyconnect version do I need on a 5505 so i can have people connect via iOS devices? Right now I have "anyconnect-macosx-i386-2.5.1025-k9.pkg" on there, will that work for iOS devices?
View 7 Replies View RelatedASA 5505 Version 8.2 or older nat (inside) 1 10.0.0.0 255.255.255.0nat (INTF4) 1 10.0.4.0 255.255.255.0nat (INTF5) 1 10.0.5.0 255.255.255.0nat (INTF6) 1 10.0.6.0 255.255.255.0nat (INTF7) 1 10.0.7.0 255.255.255.0global (outside) 1 209.165.200.235-209.165.200.254 netmask 255.255.255.224global (outside) 1 interface
I believe this setup does the following. The inside interface and interfaces 4,5,6,and 7 will translate using this line....
global (outside) 1 209.165.200.235-209.165.200.254 netmask 255.255.255.224
and if the addresses run out is will start using the ouside interface IP address to translate, so traffic is not disrupted and is based on the line of configuration.....
global (outside) 1 interface
My question, does it do this because of the order of the configuration..
global (outside) 1 209.165.200.235-209.165.200.254 netmask 255.255.255.224global (outside) 1 interface
or would it do it that way even if it was like this?
global (outside) 1 interfaceglobal (outside) 1 209.165.200.235-209.165.200.254 netmask 255.255.255.224
and if so why?Now let's convert the above configuration to ASA 5505 Version 8.3 or newer.
object network OUTSIDE-NAT-POOLrange 209.165.200.235 209.165.200.254object network INTERNAL-SEGMENTSsubnet 10.0.0.0 255.255.248.0nat (any,outside) dynamic OUTSIDE-NAT-POOL interface
My question is how does it know to use the outside interface as a backup when the OUTSIDE-NAT-POOL is depleted?Also why do I need to define the INTERNAL-SEGMENTS ? Doesn't the "any" in the (any,outside) take care of that?Also wouldn't the "any" in (any,outside) cover interface 3 or DMZ which could be an issue?
I have a ASA5505 and currently running Version 7.2(4). I was wondering what the latest version of the software would available to me would be.
Here's a show ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
Compiled on Sun 06-Apr-08 13:39 by builders
System image file is "disk0:/asa724-k8.bin"
Config file at boot was "startup-config"
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
I've have an ASA 5505 with a inside network vlan1 (192.168.0.0/24) - i've configured an IPsec VPN profile and a VPN network of 192.168.0.50/24. I can through my VPN tunnel access inside hosts on vlan1 - but not ASDM on the ASA (192.168.0.1). Under management i've added the VPN network of 192.168.50.0/24 to have access to ASDM, but still does not work.
View 1 Replies View Related I'm trying to configure UC-Proxy using an ASA 5505 with software version 8.0.4.I was following the instructions in DOC-5704 and ASA 8.0 CLI.I don't have USB security tokens in UC solution, instead I'm using IP phones Cisco 7961 with MIC.I configure all the items as the documentation says but when I restart the phone outside the Firewall, the 7961 don't registrate with the Call Manager.Checking the troubleshooting I found that it's possible certificates problems but I don't know if I need to do something in phones.
I would like to know if there is any consideration when the UC proxy works just with MIC.The outside phone is a Cisco 7961 configured with static IP address and TFTP address of Call Manager (static NAT in ASA).
I just upgraded my firewall to ASA 5505. Now, my original static ip address cofiguration is gone. Apperantly, Cisco went away from static ip address to something like nat (inside,outside) dynamic interface. how to create a static ip address under version 8.4? By the way, I am sharing what my configuration used to look before upgrading.
!
hostname cisco-asa
domain-name default.domain.invalid
names
!
interface Vlan1
nameif inside
security-level 100
[code].....
Showing Your firewall has a version number null which is not supported by ASDM 6.2(5). I received this error when trying to run asdm on my asa 5505. I upgraded image and asdm trying different versions. I used many different versions of java all to no avail.
View 4 Replies View RelatedI am now going to configure IPSec VPN connection for Cisco ASA 5505 (Version 8.4)
View 3 Replies View RelatedI have upgraded an ASA 5505 to 9.0(1) as I would like to use ipv6 version of dhcprelay. That said, I am unable to obtain a global unicast address but the link-local address is able to communication with the ISP's gateway/DHCP provider which I hope will allow v6 dhcprelay provide internal clients with IP's from the ISP. Trouble is, unsolicated inbound ICMPv6 messages from the ISP's gateway are being dropped on the way into outside interface.
%ASA-3-313008: Denied IPv6-ICMP type=129, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
%ASA-3-313008: Denied IPv6-ICMP type=131, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
%ASA-3-313008: Denied IPv6-ICMP type=131, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
[Code]...
provide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View Relatedi am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View RelatedI have been using ASDM on a "Cisco Adaptive Security Appliance Software Version 8.2(5)" for a long time and in order to route packets among the interfaces without NATting the packets, I have always been using the function "Add NAT Exempt Rule" under "Configuration -> Firewall -> NAT Rules". Everything has always been working fine.
Now I am trying to use ASDM on a "Cisco Adaptive Security Appliance Software Version 9.1(1)" and I cannot find how to do the same operation: the "Add NAT Exempt Rule" option is no longer available and the only way to make the traffic passing through seems to be NATting it on the OUTSIDE interface.
where I am mistaking? My goal is to let the traffic passing through from the inside interface to the outside interface without being translated.
I want to configurate cisco ipsec vpn client at asa 5505. At my asa the software version is 8.4. Any link or some material to config ipsec vpn client at asa 5505 version 8.4.
View 1 Replies View RelatedOn the downloads page there's a 9.0.2.ED listed as the 'latest' but then if I expand the '9' below it I get to 9.1.1.ED. Which one is the actual latest? is there any way to tell the one that is not an 'interim' version I think 9.1.1 is also listed under interim?
View 4 Replies View Relatedbasic step to blocking site on ASA 5505 version 8.2(1) base license using CLI
View 1 Replies View RelatedI use a ASA 5510 and a ASA 5505 and want to connect 2 networks via VPN ASA software version is 8.41. Network 1 has address 192.168.90.0 Network 2 has the address 192.168.5.0 I use site to site VPN wizard on both asa and create the VPN connection. do I need to create acl after that?the PCs on network 1 must have access to a resource in the network 2 how do I create static routing to connect the both Network.
View 1 Replies View RelatedMcAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies View RelatedI am currently migrating a netscreen firewall to a asa 5515 version 8.6 The issue is setting up the management connectivity.
basically the management IP of the cisco asa is not advertised. But, we want to route a management IP through the management interface to interface Gi0/2.
so IP of management interface is say - 216.10.100.10. and the IP of the inside interface is say - 198.1.1.10/24 on our router we have a static route sending 198.1.1.0/24 to next hop of 216.10.100.10 (management interface of cisco asa).
On the Cisco ASA can I send the traffic to the inside interface and manage the firewall via ssh that way?
I'm trying to install an ASA 5510 transparent firewall using ASA version 8.4(3)9 but I don't understand how traffic will ever pass through my firewall if both interfaces are on the same sub net(V lan) as the host and it's default gateway? The reason I'm doing this is were installing UAG (or Direct Access) and the UAG appliance need to have public IP's but still be behind a firewall (see attached diagram).
Looking at the documentation (which all seems to be for 5505's running 8.2) it almost seems like i need to have the transparent firewall 'in-line' to the ISP router?, but this router services another IP address range on another v lan for other (routed) firewalls (not shown on diagram) so putting it 'in-line' is not possible. Surely this can't be the case can it? If not how is it supposed to be cabled up and configured so packets go through the firewall?
How are asa5540 in high availability mode upgraded for their versions.
View 1 Replies View Relatedconfiguring NAT on intranet firewall. here is the my topology:
DMZ Network - - - - - - - - - External Firewall - - - - - - - - - Internet
|
|
|
Internal Network - - - - - - - - - Internal Firewall
1) I can Ping the intneral host from external firewall, internet firewall and DMZ network
2) Both ASA's are running OS Version 9.0(1)
3) ACL used permit IP any any, on both (i.e inside and outside)
NAT configuration on Internal Firewall (Identity NAT)
object network MGMT-SRV-INSIDE subnet 10.10.10.0 255.255.255.192
object network MGMT-SRV-identity
subnet10.10.10.0 255.255.255.192
object network MGMT-SRV-INSIDE nat (Inside,Outside) static MGMT-SRV-identity
[code]....
I would like to know how can I block a ip address from the CLI at the Cisco PIX Firewall Version 6.3(4)
View 4 Replies View RelatedI would like to know whether CSM 4.3 is compatible with ASA version 9.1(1). Any appropriate url that contains information about these two version's compatibility?
View 2 Replies View RelatedI try to convert a CISCO ASA 8.2 version to 8.4 BUT, I have a small or "little" problem :On Cisco ASA 8.2.x, i have a possibility to create multi-line global with different subnet.Example :
global (outside) 2 217.1.x.65-217.x.x.66 netmask 255.255.255.240
global (outside) 1 interface <-- Ip interface is other subnet : 217.3.x.3
global (outside) 2 217.1.x.67 netmask 255.255.255.240
nat (inside) 1 0.0.0.0 0.0.0.0
nat (dmz2) 2 192.168.4.0 255.255.255.0
What is the method or solution to translate multi-global in 8.4 ? with static translation in 8.4 : i try to use different server in inside's zone, but not in same network on outside. In 8.2 Firmware, it's very easy to use that, but in 8.3-8.4 version, i don't have some idea to manipulate ...
interface Vlan1
description Lien vers reseau Interne Client
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0
[code]....
We want to make an upgrade of one of our customers' ASA 5520 (with failover). They have version 8.2 now and we want to get the more stable newest one. Can we get an 8.6 version? or we need an ASA 5500X for that one?
View 2 Replies View Related%ASA-3-305005: No translation group found for tcp src inside:211.155.169.186/1433 dst outside:42.121.87.89/6000, I found this error ,but the IP 211.155.169.186 is public address. I check the configuration but didn't find any information about this address.I don't understand why src is inside? How can I solve this error?
View 1 Replies View RelatedWe have 2 firewalls on PIX facing the Internet and connected to interface e1 (behind it) an ASA version 8.3 Both the PIX (Firewall facing) and the ASA are on the same subnet.
By using Routing statements and statics I have been able to reroute specific traffic to the ASA5520 version 8.3 Now I need to inverse the 2 devices. The ASA5520 will be facing the Internet and the PIX will be behind it.Unfortunately the ASA5520 is refusing to route the traffic to the PIX. The access-lists are open accordingly and a NAT on the ASA has been created.
what the new command is for NAT in version 8.3?The config i have is from Version 7.2 and doesnt work on 8.3. [code]
View 12 Replies View Relatedhow to configure ip sla monitoring on asa ver 7.0 (6) ?
View 4 Replies View RelatedI try to setting up a PIX firewall to server as firewall end point for a small network for Internet access. I had include PIX configuration setup, I had replaced IP address information by sentence which describe them since IP Address is sensitive information in our network.
For some reason NAT process doesn't work in log I always receiving this kind of messages :
106011: Deny inbound (No xlate) tcp src inside:INTERNAL_HOST_IP/2490 dst inside:HOST_PUBLIC_INTERNET_IP/80
106011: Deny inbound (No xlate) tcp src inside:INTERNAL_HOST_IP/2490 dst inside:HOST_PUBLIC_INTERNET_IP/80
106011: Deny inbound (No xlate) tcp src inside:INTERNAL_HOST_IP/2491 dst inside:HOST_PUBLIC_INTERNET_IP/80PIX Configuration
[code]...
I have PIX515 with version 7.0 installed, so can i install version 8.3 on it?and what will be the memory requirements?
View 2 Replies View RelatedI have to test new Cisco ASA's IOS version 8.4 in my GNS3 LAB . do provide the link for downloading the same.I dont have direct download access from cisco.com.
View 1 Replies View Related