Trying to set up a stateful failover with two. asa5510
Here is what I have so far, tell me if this looks right. The ip address are set to 0.0.0.0 only for this discussion.
Config Primary Firewall:
config t
interface management 0/0 ip address 0.0.0.0 255.255.255.252 standby 0.0.0.0
interface eth 0/0
[Code].....
I have an ASA5510 and I would like to implement something like this: have two ports patched in and ready but only one active, the other one in standby (when the first one goes down the other port comes up and all the traffic goes down this way), all these on one physical box. So, it's basically like port failover on the same box.
View 1 Replies View RelatedI have a pair of ASA5510 currently running as a failover pair. For some reason we need to move one of the firewall to another site, is there any best practice on splitting up the failover pair then I can re-configure the secondary unit offline?
I'm thinking to power down the secondary unit, unplug it from the network totally then erase the configuration on the secondary unit on console so I can re-configure it. For the primary unit, I will disable the faiolver config by "no failover" on the primary unit. Is that necessarily all thing for splitting up the failover cluster?
Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB(code)
I have just finished setting up two ASA5510s in Active/Standby Staeful failover, using the Management interface for both failover and state. Everything appears to be working well.Configurations were transferred and the "sh failover" on both accurately reports their status before and after a failing the active device.I monitored the inside IP with a continuous ping (using a Windows client) and noticed that there were usually two to three ping responses lost. Is this normal?
View 1 Replies View RelatedMy customer had a spare ASA5510 bought a few years before with 5 x FE and security plus license with HA. Now they would like to buy a new ASA5510 to configure HA with the spare one, but now the ASA5510 comes with 2GE+3FE. Can the two FW work in HA?
View 4 Replies View RelatedDo I correctly understand that when two ASA 5510 are in fail over pair, the switchover from primary to secondary if one interface of primary goes down shall happen ONLY if failover link is up? So when the fail over link is down and one interface on primary got down also, interface tests between the two ASAs still are being done , but secondary SHALL NEVER try to become active.
In this case why to make tests on data interfaces ? What is the reason to make them? If the knowledge of that some interfaces of primary became down comes through failover link - no need to make additional interface tests - primary will tell about the failure to secondary. If so should run no monitor-interface if name command to dis load devices and network by foolish tests?
I am a single ASA-5510 with CSC module.I want to pair it for active/standby mode for failover .... can it be done if second ASA doesn't have the module? Can I assume the in case of a failover, the traffic won't be checked, and primary does in case CSC module fails?
View 2 Replies View RelatedI have a working DMVPN solution. I am trying to stand up a secondary DMVPN hub at our disaster recovery site. We are trying to deply to a Dual HUB SIngle DMVPN solution. The HUB2 DMVPN router has an INSIDE trusted interface and has an OUTSIDE UNTRUSTED interface.
The inside is 10.248.11.X...the Untrust/public is 192.168.93.11 which is connected to our DMZ 3 on the ASA 5520.....then I am trying to NAT the 192.168.93.11 to an outside public IP 199.248.30.X....just not working...have had 2 tickets open with Cisco this week and they still are unable to resolve. I am sure it is the ASA5520 is not configured correctly.
I have setup ASA5510 in failover mode. I am planning to use this setup for clientless SSL VPN and have following questions.
1. Do I have to license both firewalls for SSL VPNs? These licenses are very expensive and why would I have to purchase it for secondary when I am not using it?
2. SSL vertificate for the firewall it self. Do I have to acquire one or two to ensure users don't get annoying message about self signed certificate? Cisco doesn't seem to have this discussion in any documents. However I found following URL discussing from somebody's experience. What's official statement from Cisco on this matter? [URL]
ASA 5510 have two model Bun-K9 and Sec-Bun-K9 from the datasheet find out difference Port related and Redundancy. My questions is : Have any major difference for Security service between two model ?
View 3 Replies View RelatedI have a ASA5510 actve/standby and create one site to site VPN with remote peer ip address xx.xx.xx.xx, Our VPN traffic running on 6 mb internet link for video conferancing traffic.Now client give another link 2 mb internet and client told to us our data traffic runnig on 2 mb link but this data traffic running on the same remote peer IP xx.xx.xx.xx.Secondly request also they need failover over the ISP link.how we implement the same on ASA 5510.
View 0 Replies View RelatedI have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies View RelatedI am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
I have two ASA5510's set up in failover, and the secondary keeps crashing after doing the interface checks when bringing failover up. This only happens if I try to upgrade the image on the secondary to anything newer than 8.4.1 (I've tried with 8.4.1-11 and 8.4.2). The primary one run just fine with new images.
I don't have the exact error right now, as I need to do a screen capture from console. It's just a huge crash dump.Are there anything I might have missed during the upgrade? Should I cold-boot both the firewalls in the correct order?
i have a ASA5510 in the office, that already configured 3 context, namely, admin, user, server.in the server context, the last running config was not saved, and there was a power trip last friday night. 1 of the sub interface was affected, and i need to recreate that interface.I am getting the below error, it only allow me to do changes those pre-defined interface.how to I create extra sub interface?
View 3 Replies View RelatedI have a ASA5510 and I have a question about the speed the ports can handle, here is one port:
-interface Ethernet0/2
- speed 100
-shutdown
- no nameif
-no security-level
-no ip address
it's ethernet and not fastethernet so I figure it will only go to 10Mbps, but at the same time I can hard code the speed to 100.
i have cisco ASA 5510 Firewall using in my network, i have planning to upgrade the Flash memory from 256 mb to 512 mb and the RAM from 256 mb to 1GB.
View 1 Replies View RelatedI got PIX 525 with failover. Due to power issue one Unit was offline for a while. During this time couple of changes was done on the Firewall.
Which Unit becomes active when I plug the Firewall unit which was offline for a while now. Each Unit has 4 Ethernet Connection
E 0/0 - connects ISP Router
E 0/1 - connects to Lan switch
E 1/0 - connects to DMZ port
E 2/0 - connects to failover unit PIX
I am trying to configure this newly purchased AP to be used for WiFi surveys, heatmaps, etc..
I cant seem to get to the web interface of the AP to make config changes, even though it is picking up an IP via DHCP and it is pingable.
I have a customer with several older Aironet 1121G WAP's. In one area of the plant the noise levels from several large motors is preventing reliable connection to the WAP, even though it is located in the same conference room as the users. I am suggesting upgrading the 1121G to the 3502I to take advantage of the Clean Air technology. This raises two questions:
1) Will a single 3502I be able to effectively handle the RF noise, or does it require a network of WAPs to function properly?
2) Does the 3502I require the CT2504 controller for the Clean Air to work, or will it function in a stand alone mode?
Currently we have one ISP1 and all traffic goes to this way. Suppose our isp1 goes down, our outside user cant get the server. All servers are nated to this ISP1.We planned to purchase a another ISP2. Shall we Configure same inside server to map this ISP2? so that one primary ISP1 goes down it will take place the outside trafficISP2.
View 1 Replies View RelatedHow to configure ASA failover for 8.4.
View 1 Replies View Relateda customer have 2 pix 525 with ver 7.0.1 in a failover configuration with serial cable and 2 sc fiber interface and 2 fastethernet 1 used for failover. the strange behaviour is that when i try to do traffic from inside to dmz or dmz to inside the maximum transfer is 862Kb/s to 1MB/s not more.... i don't understand what's happened. the show mem and show cpu are normal 7% mem used and 1-2% cpu used. attached you will find the configuration.
View 5 Replies View RelatedIs it possible to setup 2 x Cisco ASA 5520 that are in an Active/Standby failover using sla monitoring?
For example ASA1 outside interface connects to an upstream switch and you setup sla monitor with icmp echo to ping that switch. The switch goes down and you need the other ASA2 to become the Active ASA. Can the sla monitor be automatically integrated with the failover commands for this to happen?
I have a ASA 5505 which is connected to a remote site which also has a ASA 5505 over a L2L VPN tunel. One of the sites has a WAN failover configured with two ISP which is working successfully.
But, when the WAN connection fails over to the backup connection the VPN link breaks as the peer site IP address has changed and the VPN can not establish a connection.
Would it be possible to configure a VPN failover so that when the connection failovers so will the VPN tunnel?
There are 2x Cisco ASA 5505 in an active/standby failover config. The primary asa 5505 has been reset and the secondary is now running as active. I would like to reintroduce the primary again but need to know how to do this.
Ideally I would like to remove the failover config and start from scratch. Do I just need to enter the following to disable failover on the active secondary box?
no failover
no failover lan unit secondary
no failover lan interface failover Vlan999
no failover interface ip failover 192.168.254.1 255.255.255.252 standby 192.168.254.2
I have a pair of ASA 5585 configured with 2 contexts, C1 & C2, C1 is active on ASA-1 & C2 is active on ASA-2 i did failover test, ping was initiated to host residing behind ASA-1 in context C1 i powered of ASA-1 then both context became active on ASA-2, however during this failover.i saw 4 ping packets drop..
View 3 Replies View RelatedConfigured ASA 5510 ISP failover and working fine.My ASA as configured as DHCP server also. So its serves IP addressing details including mask,default-gateway, DNS server IPs.Here my issue is whenever my ISP failover occurs my ASA sends previous ISP DNS server IPs to my inside clients.
Here i like to configure my ASA to serve IP addresses dynamically.Or is there any global DNS IP addresses which will work for all ISPs?
So we currently have a T1 connection at our location. We were looking to add a high speed cable internet and add an ASA 5505 with Security plus license to do failover between the two. I have found a few examples on how this would work but curious about a couple things.
We would want the Cable to be the primary, T1 as a backup.Currently the IAD that handles our T1 does dhcp, dns, and NAT.. Who/what would handle these items with the setup above?
I have a cisco asa 5510 with security plus license in Live enviroment . I need to add a secondary firewall . I was planning to do in active /standby mode for failover .But i have a doubt , when i do "show version " on live asa output says Active /active failover , does this means that i can only configure failover in active/active mode not in active/standby (which i want to do )?
Maximum Physical Interfaces : 8
VLANs : 20, DMZ Unrestricted
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 25
WebVPN Peers : 2
Dual ISPs : Enabled
VLAN Trunk Ports : 8
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This platform has an ASA 5505 Security Plus license...
i am using Cisco ASA5510 Firewall in my Network in the distrubition Layer .Private Range of Network Address use in the Network and PAT at the FW for address translation.presently encountering an issue the users behind the FW in my network unable to RDP at port 2000 presented at the Client Network.Able to Telnet on port2000 but not RDP . any changes needed at the FW end to get the RDP Access.
View 12 Replies View RelatedCisco Aironet 3602I is stand alone or need a controller ?
View 8 Replies View RelatedI have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connected to a projector and some ipads. My idea was to put the devices locally in the same closed network for share via AIR Mirror the ipads on the apple TV.
View 3 Replies View Related