I have Vlan 100 (inside) and Vlan 65 (Outside)I'm trying to configure RDP and ping traffic from Vlan 100 to Vlan 65 One way.If I connect 2 PCs on E0/0 and E0/1 they can happily ping the their own VLAN ip add 192.168.100.3 and 172.16.65.1I've copied my config,
ASA Version 8.4(4)1
!
names
!
object-group network A_Network
network-object 172.16.65.0 255.255.255.0
[code]....
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies View RelatedInternet ISP -> Juniper SRX 210 Ge-0/0/0
Juniper fe0/0/2 -> Cisco ASA 5505
Cisco ASA 5505 - >Inernal LAN switch.
1. Internet is connected to Juniper Ge0/0/0 via /30 IP.
2. Juniper fe0/0/2 port is configured as inet port and configured the Internal public LAN pool provided by the ISP. And this port is directly connected to Cisco ASA 5505 E0/0. Its a /28 pool IP address. This interface is configured as outside and security level set to 0.
From Juniper SRX, am able to ping public Internet IPs (8.8.8.8).
Issue:
1. From ASA am unable to ping public ip configured on Juniper G0/0/0 port.(/30)
2. From ASA no other Public internet IP is pinging.
Troubleshooting Done so far.
1, Configured icmp inspection on ASA.
2. Used the packet tracer in ASA, it shows the packet is flowing outside without a drop.
3. Allowed all services in untrust zone in bound traffic in Juniper SRX.
4. Viewed the logs when I was trying the ping 8.8.8.8 in ASA. It says "Tear down ICMP connection for faddrr **** gaddr **
I have interited an ASA5505 problem. We're trying to manage the ASA remotely - we can connect to the device remotely via IPSec, we can ping other devices on the LAN network, but cannot ping the inside interface of the ASA - nor can we telnet/ssh/http to it. We can, however, connect to another router that's on the LAN and then SSH into the ASA's inside interface.
My IP via VPN: 10.133.20.8
The ASA interface we're trying to connect to via SSH or ASDM: 10.4.209.254
A router on the LAN we can connect to 10.4.209.250
We can ping other LAN devices such as 10.4.209.75, .90, .150 - so it's not a NAT/Route/Split Tunnel issue.I've attached the ASA config.
hostname ASA5505
enable password XXXXXXXXXXX encrypted
passwd XXXXXXXXXX encrypted
names
name 10.4.209.248 rpm_router
[code]....
I'm a CIsco ISR, Setting up my first ASA, which seems to be going well.I've setup an IPSEC VPN to a non Cisco device. And have connectivity between devices in each subnet.
-Subnet A - non Cisco - 10.10.13.0/24
-Subnet B - ASA 5505 - 192.168.2.0/24 (ASA is .254)
From Subnet A I can ping every device except the ASA on .254.
Edited Config attached, IP's changed for privacy, passwords removed.Let me know if I've removed too much of the config.
I just try to ping a internal Host but it want to go.
Laptop<===>ASA5505
Connected is the Laptop at Ethernet 0/2 Inside
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
But If I try to ping to the Laptop I get the followed:
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
From the Laptop to the ASA5505 I can Ping successfully.
I have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12
???????????
100% lost
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
am not sure if it is different on the 8.2 or if I am missing something. I can connect to the vpn but cannot get to the inside computers. I can ping them from the ASA but not from the vpn client.
View 17 Replies View RelatedOne of our ASA5505 can not ping the gateway today. But when I use a notepad , using the same IPs, it can ping the gateway !!!
It is so strange, the ASA5505 was working ok before until today.
Is there anyting I can do to check whether the ASA is ok ?
I have a ASA 5505.|I configured it for remote access VPN from cisco VPN client.the ASA receives a public ip address on outside interface via PPPoE.I can connect to public ip of outside interface and address 10.1.1.2 is assigned to my Cisco vpn client.the problem is that I Cannot ping or reach ASA internal IP address 172.16.29.1 in any way when I am in VPN from outside,while I Can ping other hosts on 172.16.29.0/24 when connected in VPN.this is a problem brcause when I am connected in VPN to ASA I Cannot configure it..Then I Wanted to ask if it is possible a configuration which gives addresses from network 172.16.29.0/24 (the same as inside network) to VPN clients instead of another network (10.1.1.0/24) [code]
View 1 Replies View RelatedI have setup a remote access VPN to an ASA5505
I have a directly connected server behind the ASA and I can ping the server without a problem.
The VPN client reports packets being encrypted and decrypted
However when I try to RDP to the server the encyrpted packets keep incrementing but the decrypted packets do not.
I am also not seeing any RDP traffic hit the server (verified by ethereal)
I have done a packet tracer and it suceeds but ends with an IP spoof which I believe is correct as it is vpn traffic and not actually being encrypted.
This is the debug from the RDP session, I am confused by a Denied ICMP on line 2 as I am able to ping the server?
%ASA-6-302013: Built inbound TCP connection 88193 for external:172.16.24.4/50984 (172.16.24.4/50984) to internal:192.168.100.146/3389 (192.168.100.146/3389) (roger_ssl)
%ASA-4-313004: Denied ICMP type=0, from laddr 172.16.24.4 on interface external to 192.168.100.146: no matching session
[Code].....
The only logical bit to this is flow closed by inspection? Does this mean the server has not responded?
And the decrypt packets not increasing when trying to RDP Does this mean that I have reached the end of my ASA knowledge on this one!
I have a normal setup of ASA5505 (without security license) connected behind an internet router. From the ASA5505 console I can ping the Internet. However, users behind the Firewall on the internal LAN, cannot ping the Internet even though NATing is configured. The users can ping the Inside interface of the Firewall so there is no internal reachability problem. In addition, I noticed that the NAT inside access list is not having any hit counts at all when users are trying to reach the internet.
When i replace the ASA5505 with a router with NAT overload configuration on it, the setup works normally and users are able to browse the internet.
The ASA5505 configuration is shown below.
hostname Firewall
interface Ethernet0/0
description Connected To Internet Router
switchport access vlan 10
[Code].....
I just get it that I can make a VPN Site-to-Site IPSec. But if I try to send a ping from one PC (network 1) to the other PC (network 2) it failed.
PC (Network 1) <ASA5505> Switch <ASA5510> PC (Network 2)
between the two ASA I have a funkctional VPN IPSec tunnel, but I can`t get access from one to theother network.
That are the access-list on the ASA5505:
asa5505#
access-list cached ACL log flows: total 0, denied 0 (deny-flow-max 4096)
alert-interval 300
access-list Inside_ICMP; 4 elements
[Code].....
i have asa 5505 with the asdm v5.2 (4), and the asa v7.2(4). This platform has a base license. if i upgrade adsm and asa on v6.2(1) and v8.2(2) if I lose my license and that you need to activate them? i configured site to site vpn (this firewall and the another) that i lose my configuration if i upgrade my firewall.
View 2 Replies View RelatedI'm trying to troubleshoot an ASA5505.
The original goal was to block "Mumble/Murmur" (a voip app) traffic, which runs on TCP/UDP 64738, both inbound and outbound, except to a certain host (63.223.117.170).
However, when nothing I tried seemed to make a difference, just to troubleshoot, I decided to try blocking all inbound traffic. I first disconnected ethernet port 0/0 to ensure that it was cabled correctly and the outside interface went down when I did. That worked as expected, so I confirmed I had the right interface and it was cabled correctly.
I then applied a "any any deny ip" rule as the first element in the outside interface access_list, as you can see below. However, it appears to have had no real effect and the hit count is very low (it should be astronomical).
show ver
Cisco Adaptive Security Appliance Software Version 9.0(2)
Device Manager Version 7.1(2)
Compiled on Thu 21-Feb-13 13:10 by builders
System image file is "disk0:/asa902-k8.bin"
[Code].....
I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
Is it possible to use IP "aliases" on an ASA5505 to use as static NAT public IPs to private IPs? For example, I have int e0/0 connected to my ISP using a /30 subnet and I have my private LAN connected to e0/1 with a /24 subnet. At the moment I can use the one usable IP from the /30 to NAT to the private LAN. The ISP is also routing a /28 subnet to the one public IP of the ASA. I would like to use some of the /28 IPs for NAT also. Can it be as easy as just adding the NAT commands? I figure I would have to add that subnet to the ASA somehow, no? In other devices (including the SA520) they use a concept called IP aliases whereby you define what additional IPs the device can use in its NAT config. Does the ASA support aliases? Maybe I have to do something with VLANs?
View 2 Replies View Relatedit is possible use 1 or 2 Gb memory with ASA 5505 or only 512 Mb ?
View 3 Replies View RelatedI have 1 network that I'm trying to make secure, and it needs to access 2 seperate networks. I tried using an ASA5505 that I had on the shelf to accomplish this but discovered that I had the basic license and that was prohibiting me from getting my connection to my 3rd network. I scrapped that idea and grabbed an old pix 501 off the shelf to bring my connectivity to my 3rd network online since the 3rd network is only passing ip traffic to a small group of servers on the outside I figure the 501 should be just fine.
So, here's the problem I am running into:My internal network is 10.10.16.0/16, I have a new domain controller with DHCP on it handing out addresses in the 10.10.16.0/24 range.External Network 1 is 192.168.16.0/24. The services I need from that network are primarily in 192.168.0.0 range, however there is a comcast router 75.123.123.123 (Changed of course) that provides high speed internet I need for my www traffic.External Network 2 is 10.1.1.0/16 I have about 4 servers I need to access on this network and that's it. This network has it's own domain and DHCP controller and I've been given a range of ip's to use on this network of 10.1.3.180-10.1.3.189 My switch is just a plane jane 3com switch with minimal management so I am attempting to use my ASA5505 to handle my layer 3 routing.
So here's my issue:ASA5505 (IN:10.10.16.1, OUT: 192.168.16.6): Passes traffic to External Network 1 and to the comcast router, no problem. All my computers on my 10.10.16.0/16 network have access to everything on 192.168.0.0/24 as well as getting full name resolution and www traffic across the comcast router. Can NOT access 10.1.1.0/16 no matter what. From inside the ASA or from on the inside LAN ports. It CAN ping the PIX 501 PIX 501 (IN:10.10.16.3, OUT: 10.1.3.180) Can ping EVERYTHING. Can ping 192.168.0.0/24, can ping 10.10.16.0/16 and can ping 10.1.1.0/16. Set to globally assign the other IP's in my range as addresses for outgoing traffic.Workstations (IN: 10.10.16.XXX DHCP, using 10.10.16.1 as gateway) Can only access everything on External Network 1. ZERO access to External Network 2. ATM I have both INSIDE and OUTSIDE ACL's wide open for both firewalls just to get connectivity going. I will be tightening it up after it is operational.Attached find a log file (Sensetive data removed of course) that contains the sh run and sh ver for both the ASA5505 and the PIX 501.
I just got an ASA 5505 with Cisco Adaptive Security Appliance Software Version 8.0(4) alredy loaded on it. Should I update/upgrade it to the newest IOS release, or is the 8.0(4) good and stable?
View 3 Replies View RelatedI'd like to setup a DMZ network with the ASA5505. Do I need the "Security Plus Bundle"?
View 1 Replies View RelatedI've been trying to get my WRVS4400N connected to my ASA5505 on the internet through a Cox connection, but it isn't working. I cannot get the ASA to be the DHCP server for the wireless router. I've configured the wireless router as a gateway and pointed the DHCP server to the ASA but no addresses are being passed through to the wireless router. I've included a copy of my config.
ciscoasa# sh run
: Saved
:
ASA Version 8.4(2)
[Code].....
We are trying to utilize a 5 ip block of addresses provided by our ISP. What we have assigned from them is like this: 10.10.10.46 - 10.10.10.50 is our ip range. 10.10.10.45 is the gateway. Subnet is 255.255.255.248. If we assign 10.10.10.46 to the outside interface how do we accept inbound traffic from the other addresses?
View 6 Replies View RelatedI have a asa 5505 Sec plus with 3vlan, inside, outside and dmz.
On the outside i have 5 ip's for my use, and in the dmz i have a webserver that need to communicate with one sql server on the inside.
The "sql" also needs to be accessible from outside and thus has a static nat with a dynamic nat so it replies from same ip as on nat ie 72.72.72.5 webserver is natted with 72.72.72.6
sql inside ip is 192.168.1.2, gw 192.168.1.1
webserver ip is 192.168.2.100 gw 192.168.2.1
sec lvl on inside is 100 and on dmz 50
with a dynamic policy running inside-net/24 to dmz-network/24 translagt to dmz 192.168.2.2 i can get it to ping 1 way from inside to dmz, but not the other way around...
All i need is to open 1 port ie 6677 both ways for this communication to work.
I'm not very familiar with the CLI and do most stuf in GUI (know i should learn CLI, but time doesnt let me)...
on access rules i have just added everything from any to any using , ip, icmp, tcp and udp just to be sure... :-)
I want to make it so if a user tries to use a different DNS server the request will be redirected to the one they should be using.I thought this might work but the ASA doesn't do PB routing
ip access-list extended transparent_dns
permit udp any any eq 53
route-map redirect_dns permit 10
match ip address transparent_dns
set ip next-hop ip.of.your.server
route-map redirect_dns permit 20
[code]....
The DNS server is windows 2003?Would policy based NAT or WCCP work for this? If so how would I go about it?
I would like to use an ASA5505 as a simple LAN-to-LAN ethernet router. My plan is to configure two interfaces with the same security level and then use the command that allows interfaces with the same security level to communicate with each other. I can get this to work without having to setup and ACLs or NAT stuff.
View 5 Replies View Relatedfor the purpose of a redundency, incase the primary ISP goes down the backup kicks in.Can this be done with the basic license (max 3 vlans) or you need to have the security plus license. (20 vlans) Currently not using the 3rd vlan (dmz)
View 5 Replies View Relatedsetting up ASA to allow passive FTP connection! I can get the FTP client to connect but it does not pull the directories. I have opened 21 and range of 55536-55566. I had some trouble gettting the range opened and saved. Normally with other small business routers (GUI) I make sure those ports are forwarded and ftp works.
Is the ftp inspection killing connection or is it my config?
ASA Version 8.4(2)
!
hostname ciscoasa
enable password vRLm0eRL2O14iLM6 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[Code].....
Do some have some realistic performance numbers for a ASA 5505 on a mixed setup with local internet breakout and site to site vpn ( and don't tell me 150 mbps 3des throughput on a 100 mbps ethernet) - what can be expected in a live environment where we f.ex feed it with a 100 mbps internet connection - with a site to site vpn with f.ex 20 office workers running office on a remote terminalserver and mixed local internet breakout.
View 2 Replies View Relatedcustomer's WAN solution, instead of buying routers, purchasing department bought ASA's (don't even get me started!). So I have 5 ASA 5505's for the branch offices and one 5510 for the Head Office. I am trying to get them to behave like routers and pass the traffic across. I set up a lab with a 5505 and the 5510 using an ethernet cable for both Outside interfaces since the WAN links are going to be MetroEthernet Layer 2 anyway.
I tried static routes, dynamic routing, I followed examples from other persons who did it and it doesn't work. I attached the configs here to show I have the default routes, specific static routes pointing the traffic out, any any rules configured as well. I cannot ping from the internal lan of the 5505 to the internal lan of the 5510.
I have 2 modules of FWSM in 6500 switch (failover).I need 5 context.When I use in routed mode (like in the picture) , I cannot ping the servers behind the firewall. (I have ping to FW context),In transparent mode, it is not happening.what is the problem with routed mode?
View 1 Replies View RelatedWe are going to impliment Spectrum (CA) in my network,i have ASA-5580-20 firewall now my spectrum server want to communicate with firewall,then only it will discover the firewall logs.Now the problem is my spectrum server is in MZ zone(10.10.10.45) security leval is 70 and my inside interface(10.20.20.101) security leval is 100.
I am unable to ping from spectrum server to firewall because of high security leval.How can i solve this problem,can i change my inside security leval to 69 then i think it will ping.