Cisco Firewall :: PIX 515 To Asa5510 W Occ Tool
Mar 29, 2011
i need to move from a pix 515e. V 6.3 to a asa v 8. From what ive read i can use the pix to asa tool to get the converted configuration file to the new asa. So far so good, however, the pix has conduits which i read must be converted via the occ tool. So i ran the pix to asa conversion then ran the occ tool on that output but i keep getting errors. It is not liking the nameif outside, inside, and dmz lines. If i manually edited them out before i run the occ tool it runs but warns there are no interfaces.
View 2 Replies
ADVERTISEMENT
Jul 9, 2012
I need want to upgrade my asa from 7.2 to 8.4. Is there any conversion tool for the configuration or should I do it myself?
View 1 Replies
View Related
Oct 28, 2011
I am trying to migrate checkpoint configs to ASA 5585 using SCT tool, this tool asking me to feed it *.W file from checkpoint which is suppose to be a rule definition file on CP, but I cant find it
View 14 Replies
View Related
Feb 8, 2012
Is there a newer tool for current versions of Checkpoint to ASA 8.4? I notice a lot of similarity between checkpoint and 8.4 now, but I still have to do it all line by line which has become a PITA.
View 1 Replies
View Related
Jun 6, 2012
ASA 5510 have two model Bun-K9 and Sec-Bun-K9 from the datasheet find out difference Port related and Redundancy. My questions is : Have any major difference for Security service between two model ?
View 3 Replies
View Related
Jun 11, 2012
I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
View 7 Replies
View Related
Jun 29, 2011
I have two ASA5510's set up in failover, and the secondary keeps crashing after doing the interface checks when bringing failover up. This only happens if I try to upgrade the image on the secondary to anything newer than 8.4.1 (I've tried with 8.4.1-11 and 8.4.2). The primary one run just fine with new images.
I don't have the exact error right now, as I need to do a screen capture from console. It's just a huge crash dump.Are there anything I might have missed during the upgrade? Should I cold-boot both the firewalls in the correct order?
View 7 Replies
View Related
Sep 10, 2012
i have a ASA5510 in the office, that already configured 3 context, namely, admin, user, server.in the server context, the last running config was not saved, and there was a power trip last friday night. 1 of the sub interface was affected, and i need to recreate that interface.I am getting the below error, it only allow me to do changes those pre-defined interface.how to I create extra sub interface?
View 3 Replies
View Related
Jul 21, 2011
I have a ASA5510 and I have a question about the speed the ports can handle, here is one port:
-interface Ethernet0/2
- speed 100
-shutdown
- no nameif
-no security-level
-no ip address
it's ethernet and not fastethernet so I figure it will only go to 10Mbps, but at the same time I can hard code the speed to 100.
View 2 Replies
View Related
Feb 22, 2012
i have cisco ASA 5510 Firewall using in my network, i have planning to upgrade the Flash memory from 256 mb to 512 mb and the RAM from 256 mb to 1GB.
View 1 Replies
View Related
May 4, 2012
I have a cisco asa 5510 with security plus license in Live enviroment . I need to add a secondary firewall . I was planning to do in active /standby mode for failover .But i have a doubt , when i do "show version " on live asa output says Active /active failover , does this means that i can only configure failover in active/active mode not in active/standby (which i want to do )?
Maximum Physical Interfaces : 8
VLANs : 20, DMZ Unrestricted
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 25
WebVPN Peers : 2
Dual ISPs : Enabled
VLAN Trunk Ports : 8
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This platform has an ASA 5505 Security Plus license...
View 4 Replies
View Related
Feb 12, 2012
i am using Cisco ASA5510 Firewall in my Network in the distrubition Layer .Private Range of Network Address use in the Network and PAT at the FW for address translation.presently encountering an issue the users behind the FW in my network unable to RDP at port 2000 presented at the Client Network.Able to Telnet on port2000 but not RDP . any changes needed at the FW end to get the RDP Access.
View 12 Replies
View Related
Mar 14, 2011
We have to use scp on all of our network devices. It worked quite well on our routers and switches but I can't seem to get it to work for the firewalls and IPS. I enabled scp on my ASA5510 using the command "ssh scopy enable". I also ensured that a rsa key was generated and that ssh ver 2 was enabled. But I can't seem to locate the commands to actually have my firewall either copy it's configuration to a server or reach out to a server to pull down a file. We are using IOS 8.2(1).
View 1 Replies
View Related
Mar 22, 2011
I have a customer who wants to prioritze rdp traffic throgh the firewall.I know that its port 3389, but outgoing traffic is a random port number.Any smart way to catch this traffic and get it in the LLQ ?
View 3 Replies
View Related
Sep 13, 2012
we have ASA 5510 which we need to upgrade from 8.0(3) to 8.2.5. can we directly switch to 8.2.5 from 8.0(3) , if not what all versions we need to go from.
What all point needs to check before that following is show flash output.
97 14635008
Jan 01 2003 14:12:16 asa803-k8.bin 98 4096
May 14 2008 21:22:10 tmp 2 4096
Apr 20 2008 02:21:46 log 6 4096
Apr 20 2008 02:22:16 crypto_archive 99 6851212
[Code] .....
View 4 Replies
View Related
Sep 18, 2011
My device has 3 interfaces configured: inside, outside, DMZ. Right now I can access the DMZ from the Internet and I can access the DMZ from the LAN using an exempt nat statement. I am having a few issues setting up DMZ > LAN access however. The servers running on the DMZ need to send information to my LAN such as syslog traffic for example. Will DMZ traffic be NATed or should this somehow be excluded? Bascially all LAN devices should get to the DMZ devices by their actual IP and vice versa. Are there any special statements I need to add to the ASA such as nat or ACLs to make this work? My LAN is 10.10.6.0/24 and DMZ is 192.168.254.0/24.
View 1 Replies
View Related
Oct 20, 2011
I have a ASA 5510 with asa8.4(2) and asdm6.4(5)205. Have a new basic config, nothing special at this time. I just cannot seem to get from the inside to the outside. From the outside interface I can ping, so I have a good Internet connection. [code]
View 3 Replies
View Related
Apr 24, 2012
WE have a DMZ on ASA5510 8.4, it can access anything internal interface but cannot get out to internet or outside interface. I try to ping from a host in the DMZ to 8.8.8.8 and get this in the log 6Apr 25 201208:24:431100038.8.8.80172.10.1.1501Routing failed to locate next hop for ICMP from outside:8.8.8.8/0 to inside:172.10.1.150/1. [code]
View 14 Replies
View Related
Apr 5, 2012
I am having ASA5510 firewall which has 1GB RAM currently. I want to upgrade to 2GB. When I opened the box, I can see only 1 slot to insert the RAM. I searched in Cisco website and I got to know that I need to use 2 x 1 GB RAM. So, I need to have 2 slots to do that. But, I am having only 1 slot in the box.
View 5 Replies
View Related
Mar 30, 2011
We have an ASA5510 with a backup ISP connection protecting our corporate network. I also have a mail server and I would like to route SMTP traffic over the backup network. I realize that the ASA5510 does not support PBR, but I also know that I can use static NAT rules as a workaround to direct specific types of traffic over a particular interface (e.g. "static (outside,inside) tcp 0.0.0.0 www 0.0.0.0 www netmask 0.0.0.0" and "static (backup,inside) tcp 0.0.0.0 smtp 0.0.0.0 smtp netmask 0.0.0.0"). is it possible to use something similar to force a particular host to use a specific interface? I have tried to make this work on my own without success. Is it even possible?
View 5 Replies
View Related
Dec 5, 2012
I bought a Cisco ASA 5510 (P/N: ASA5510-BUN-K9) and i would like to know if i have to buy some license,What i mean is, for the basics, it still being necessary aquire some license?
View 3 Replies
View Related
May 31, 2011
We are about to upgrade our ASA's from 7.04 to 8.2. Obviously I will be opening a TAC case to assist with the upgrade and I will also be upgrading ASDM software at the same time. These production firewalls are paired with an active --> failover scenario and not active --> active. I had previously engaged cisco regarding the upgrade and they have recommended an upgrade path to ensure success. Also, I have a pair of test ASA's that I've gone through the upgrade process with - documenting the changes in commands and any changes in my config (I didn't notice any).So, the reason for my post is this: What are the gotcha's that you may have run into when upgrading your ASA's?These are fairly high visibility ASA's and any downtime due to the upgrade needs to be mitaged as much as possible.
View 1 Replies
View Related
May 26, 2012
I have a 2811 ISR configured to provide the following services to my network:
Internet access to LAN users Cisco Call Manager ExpressSite-to-stie VPN to 3rd party networksVPN server to provide VPN access to remote usersSecurity Zone configurationsStatic NAT configurations Now I recently just got the ASA5510 device and I am not sure how to go about with the setup, whether to put the ASA in between the internet and the ISR (Internet - ASA - ISR - LAN), or put the ISR in between the internet and the ASA (Internet - ISR - ASA - LAN)?
While i know I can move most of the config unto the ASA, i know that the CME cannot be moved, hence I would like to do the setup such that users on the network still have access to CME.
View 5 Replies
View Related
Apr 24, 2012
We have an ASA5510 and I am getting absolutely no response from the console port. Not even a blip when I turn it on. If I leave the compact flash in the internal bay, I get Green Power, Amber Status, Amber Active and Green VPN when I start it up. The Flash LED flashes Green twice then goes out. If I move the compact flash to the external bay, all of the other lights remain the same as described above but the Flash LED goes to steady Green. How ever, there is still no response whatsoever from the console port. Have replaced the DIMM but that had no effect. This is a four (4) slot ASA5510 and I have just the one DIMM in slot P13 as described on a post I found. The power supply fan comes on as well as the two (2) fans that cool the heatsink. The other two (2) fans on the expansion module side do not come on.
View 1 Replies
View Related
Aug 17, 2011
We just switched to a 5510 from a PIX 515 last evening, and the only things that are not working are any services from the outside to the inside. Example: I am unable to connect to a RDP server on the inside from the outside. I've been looking at the config for the past five hours, but am unable to see my mistake. Running 8.2(1) People on the inside are able to get out.
domain-name aaaa.org
names
name 10.10.8.13 mailserver
name 10.10.8.12 video-conf
name 1.1.1.2 PubMail
name 1.1.1.3 VidCon
name 1.1.1.5 Ms-Aderson
!
[code] .......
View 6 Replies
View Related
May 15, 2013
Upgrade from firmware 8.21 5o 8.31? I am installing 1GB of memory in my ASA 5510 and in the process I have upgrade the firmware.
- Will the upgrade change my configuration or will I have to change this manually myself at some point
- What is the meaning of "Real IP" I am not sure what the means (reading up on it now)
- What else should I be concerned about during the upgrade?
View 2 Replies
View Related
Jul 17, 2011
We have an ASA5510 which keeps resetting itself for no apparent reason. It does this several times a day and I cannot see any pattern to the times etc. I don't believe it is load related as it also happens overnight when very little is going through the device. When it happens the device just drops off the network (all interfaces) and then when it comes back a few minutes later we can see from the system uptime that it has in fact rebooted itself.
I initially thought it was faulty hardware, so I swapped the device for another 5510, but that does the same thing. I then added a third 5510 and configured it in with the second one as an Active/Passive failover pair. Both devices do the same as the first, the only differences now is that the passive device kicks in and takes over, so we have a little less service disruption each time.
View 3 Replies
View Related
Aug 25, 2012
We have network topology:
Inside Network (172.168.1.0/27) --- ASA5510----- Outside network (192.168.10.0/24)
ASA5510 have: Inside interface: 172.168.1.30/27; outside interface: 192.168.10.254
And we config:
# object network obj_inside
# subnet 172.168.1.0 255.255.255.224
# nat (inside,outside) dynamic interface
[code]...
So, we í in from outside, we can't access web at 192.168.10.10?
View 3 Replies
View Related
Apr 25, 2012
I have 30 IP cameras with a private IP address: 10.1.1.1 – 10.1.1.30. I have a Cisco ASA 5510 firewall. I want to be able to use one public IP address, example, 50.50.50.50
With a specific port to go to a different internal camera,
Example
50.50.50.50:3001 should be NATTED to camera 10.1.1.1
50.50.50.50:3002 should be NATTED to camera 10.1.1.2
[code]....
How do I do this? I know how to create NAT… just not like this.
View 5 Replies
View Related
Jan 26, 2012
I have a requirement to NAT a spare address on the same subnet range as one of the firewall interface - however, because this is not allocated to a physical interface, there is no mac entry in the arp cache. the other end of the link from the firewall is connected to a router which has no idea how to reach this "virtual address" - again because there is no entry in the arp cache I have tried to put a static arp entry into the firewall but this doesn't appear to work either. Should I be using a mac address form a physical interface or can I create a dummy mac for this - If the router can't see the ip address, then users will not be able to target this address - so that the firewall can NAT to the real outside address.I have tried routes to null0 on the router and static arp entries on both devices but the user just times when trying to connect to 10.2.7.11 (nat to 10.2.32.11)
View 6 Replies
View Related
Sep 30, 2012
At the moment we want to connect the ASA on two seperate internet connections . We create one LAN interface and two WAN interfaces. Now we want to create nat rules nat our outgoing traffic. After some research and testing (on a 8.0(4) asa) we have it working.
But now we want to implemate it on our ASA, but it works a lot differerent. I can't create a nat pool (at the 8.0(4) i can assign the second interface to the existing pool) wit two interfaces,
View 1 Replies
View Related
Sep 28, 2011
I'm currently working on migration from CSS to ACE. The ACE appliance is running A4(2.0) code. And i couldn't find the CSS to ACE conversion tool in the Web gui.
View 2 Replies
View Related
Jul 14, 2011
I have recently installed several of the new WS-500 series switches into my networks and much to my surprise they are not supported by the CNA tool as the older 500 series were. I tried using the CCA tool, but my routers and legacy switches are not supported under it. One of the reasons I bought the Cisco switches in the first place is because I wanted to use one tool to manage all components in my network. I feel rather irked about what seems to be a purposeful hampering of functionality of the SMB line of equipment. Is there a management application that will allow me to manage all of my Cisco devices from the same console?
View 3 Replies
View Related
