Cisco Firewall :: Getting PIX 506 (6.3) Configuration Query?

Jun 5, 2012

I inherited a PIX 506 with 6.3.  I will admit my background is more towards switching/routing.  But while I know it is dinosaur, I need to maintain for partner interoperability.  I just want to confirm that what I am thinking is correct and inf not how I can correct it.My thought is that since the access-list command doesn't list "eq" at the end, all ports and protocols are allowed?The other thing I am not used to is that the access-list has not id/number included in the command, so I assume that access-group specifies this functionality.
Here is a snippet of the current config:

object-group network Ext_Net   network-object
object-group network Int_Net   network-object
object-group network DNS   network-object   network-object
object-group network Servers   network-object   network-object   network-


View 2 Replies


Cisco Switching/Routing :: 5548 Nexus 5K And 2K - Ports Configuration Query

Feb 16, 2013

I have two 5548s as core. 8 FEXs are multihomed (advanced vPC topology?) to both the cores.Suppose, I have to configure a bunch of ports on the FEXs, say Eth101/1/10 - 20. I would login to the first core and apply the configs.
My question is - do I have to do the same on the second core also? Or would the first core replicate the stuff to the second core? I know about port-profiles/CFS and such. But, without that would it automatically sync to second core?
For testing purpose, I went to Core 1 Eth101/1/10 and put a description "TEST". Wrote the config. After 5 minutes logged into second core and did show run Eth101/1/10. But, the description "TEST" didn't show up there.
Also, doing sh run on any FEX port is faster on one of the cores and very slow on second core... all the FEXs have 20 GB uplink to core 1 & 2 (so total 40GB in vPC, max pinning 1)

View 2 Replies View Related

Cisco Firewall :: Allow Dmz Zone Server To Resolve Only Dns Query Through Nslookup On ASA 5540

May 2, 2012

How I can allow dmz zone server to resolve only dns query through nslookup on ASA 5540? What is the configuration required on ASA 5540 ?

View 13 Replies View Related

Cisco :: ACS 5.3 License Query

Dec 12, 2011

If i require ACS 5.3 in HA. Do i need to procure two ACS with the add-on licenses?

View 1 Replies View Related

Cisco VPN :: Asa 5500 Query Reg Vpn Creation

Feb 8, 2011

i have a query regarding the no. of isakmp policy priority creating..when i create a new policy in ASA 5500 firewall, i get the below error...i assume it will support only 20 nos, where as we can use between 1-65535.. can anyone from cisco confirm it...running version is 8.x & VPN Plus license.Policy limit reached. No more than 20 isakmp policies can be configured.”

View 2 Replies View Related

Cisco WAN :: QOS Marking Query Of 7206VXR

Nov 2, 2011

We have subscribed for MPLS links from Service provider we have a DC where the core connectivity is 90 MB and Remote branch location Connectivity is 64 Kbps. We are in process of enabling QOS for our links with co-ordination with Service provider ; as per our finding the branches have more RX traffic (downloading) so after discussion with provider we were advised to mark traffic from the core end and give it to the provider.The provider at its PE will honor the marking and set some B/W percentages and prioroty based on the DSCP marking values.
We need to mark this traffic so it is feasible to mark the traffic at the core DC router which has the below H/W details,Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory.
Processor board ID 36161439
MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2
6 slot VXR midplane, Version 2.11
or is it feasible to mark the traffic at the core switch.

View 6 Replies View Related

IPv6 - No DNS Query When Using Firefox And IE?

Feb 8, 2011

I am setting up a Linux apache and bind server to test the behaviour of Windows XP,Vista, 7 and Mac OS X.I have setup a apache and bind already and they were tested individually. I used Firefox and IE to access the apache page by type in the IPv6 address and the page was showed correctly. And I have tried to query the AAAA record of a local zone "" in my Bind server using nslookup and the result is good too.However, it is strange that I cannot get it work if I type in the FQDN "" in Firefox and IE. I tried to capture the IPv6 traffic in Wireshark (Attached in this post) and there are no DNS query when I try to access the page. Is there anything that I have to set to get it work properly?(Actually I have tested the same thing on Mac OS X and Vista too but the result is the same)Below is my Windows 7 network setting and some nslookup query:

C:Usersvmware>ipconfig /all

Windows IP Configuration"

Host Name . . . . . . . . . . . . : vmware-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No


View 7 Replies View Related

Cisco WAN :: 2960 Network Design Query

Aug 22, 2011

I am in the process of planning our new network. Our business is changing from hosting its own data centre, to moving it to a professional facility. We have 120 users, over 100 servers (physical and virtual) and three sites (main premise, data centre, dr site). The new network will connect all three. Our new WAN links are almost ordered. We will be making use of a managed MPLS IP VPN, with a 100M access rate at each site. I am currently focusing on the desing of the network at the main business premise. We have a significant investment in Cisco 2960 & 3750 switches and Fortinet firewall appliances. I plan to re-use these in the design.
Our current LAN is very flat and I want to segment the network. My plan is to create a number of VLANs, enable the Inter VLAN routing on the 3750 and then attach the 3750 to the Fortinet appliance which will provide stateful firewalling and traffic policin based on the VLAN (subnet) addresses. It is important that the traffic be routed as quickly as possible from this site to our prod and dr data centres.The 2960's act as the access layer, the 3750 as the distribution layer. The 2960's will connect via port channels (layer 2) to the 3750's and the VLAN interfaces will be configured on the 3750.
I was then planning on creating a VLAN on the 3750 to connect to the Fortigate appliance with a /29 address to limit the addresses used whilst also providing some flexibility for any future design changes.I want to implement a little security between the VLANs on the 3750 switches. I have a question about this coming up.I then plan to use the Fortigate appliance to do basic traffic policing based on source/destination addresses.
The WAN routers will connect to the Fortinet appliance on a Gigabit copper interface. The WAN routers will run HSRP between themselves and only one router will be active at any one time. The failover will be managed by the Fortigate and Cisco routers.I plan to define those addresses hosted at the other data centres and associate them with the interface associated with the WAN.I will then define the routing on the firewall for the two other data centres through summary routes for each of the sites. We will run static routing from the Cisco 3750 to the Fortigate and Fortigate to WAN router. We have no other networks/sites and won't have any others in the future.

View 25 Replies View Related

Cisco :: / WLC And ACS Specific Authentication Criteria Query

Sep 29, 2011

I have a wireless network with WLC and WCS and ACS integrated for user authentication.Web login has been enabled on the WLC and authentication of Username is done through ACS.
Q1. For specific SSID (TEST) specific username (Tom) is used for authentication,where as Tom cannot be used for authentication for any other SSID.
Q2. Weblogin page pushed by WLC is https on virtual IP want it to be pushed through http protocol.

View 1 Replies View Related

Cisco WAN :: Ethernet Link Query With 7609

Aug 27, 2011

We have Cisco 7609 Router and one 6 Mbps link which is on ethernet . When we are trerminating on Gigaethernet of 7609 router it is not coming up. While same link is showing up and working fine on other routers which is having Ethernet interface.

View 1 Replies View Related

Cisco VPN :: RV042 Query Regarding VPN Setting In Linksys

May 29, 2011

I have a Linksys RV042 and I came aceoss the setting " Dynamic IP+Domain Name(FQDN) authentication" setting under the Local Security Gateway type. How this option actually works. I tried googling but couldn't find a proper link.

View 1 Replies View Related

Cisco :: LMS 4.2.3 Query On Interface Utilization Report?

Mar 2, 2013

Interface Utilization report displays the interface utilization data for each device polled for the Interface Utilization template. The information is presented using the percentage specifier.
For eg its displayed % (Rx Max%,Rx Avg%,RxMin%,
Tx Max%,Tx Avg%,TxMin%)
I wants report should have the data(interface utilization In Bytes of data)Can we display the data instead of the percentage?

View 0 Replies View Related

Blocking Telnet On SQL Port Query

Mar 8, 2011

I was unable to telnet in to a SQL server on port 1433 to test the connection from the client PC.the application could connect and this alone verifies it is working on port 1433 for sql.My question is how can a telnet command on a specific port be blocked ?

View 3 Replies View Related

Wireless Access Point Query?

Sep 23, 2011

I think I know what I'm talking about here, I just need someone to confirm that what I want to do is possible, and the way Im planning on doing it will work..Basically, I have a sky router (sagem model), and the wireless is weak upstairs in my house.So, I have ordered a new access point.What I want to do is keep the same wireless ssid and key etc, so my devices just connect.

View 6 Replies View Related

IP Query For Remote Desktop Connection?

May 24, 2011

Is it possible to find out the IP address of a PC connecting via Remote Desktop Connection.Running XP Pro on a network,I have admin rights to the PC's, but no direct access to the servers.Event viewer shows some details, but no IP address.

View 3 Replies View Related

Cisco :: SNMP / Query Dot1dStpPortState On Catalyst 2960-S

Dec 10, 2012

I would like to be able to query the dot1dStpPortState obect on the Catalyst 2960-S on our LAN . Im running firmware c2960s-universalk9-mz.122-55.SE2.bin and according to the Cisco SNMP Object Navigator the object is supported (via the BRIDGE-MIB).However when i query using snmpwalk from my workstation :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x I receive and error .SNMPv2-SMI::mib- = No Such Instance currently exists at this OID For the sake of comparison, querying our 4700 :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x returns (as expected, cropped)
SNMPv2-SMI::mib- = INTEGER: 5
SNMPv2-SMI::mib- = INTEGER: 5
SNMPv2-SMI::mib- = INTEGER: 5
SNMPv2-SMI::mib- = INTEGER: 5
SNMPv2-SMI::mib- = INTEGER: 5
SNMPv2-SMI::mib- = INTEGER: 5
SNMPv2-SMI::mib- = INTEGER: 5
SNMPv2-SMI::mib- = INTEGER: 5
Is there some special configuration i need to do on our 2960's. The only snmp related settings i can see in the running config is snmp-server community. In this case :
snmp-server community bic-zua-ro RO

View 3 Replies View Related

Servers :: Failed To Send DNS Query To Server

Apr 21, 2011

Kerio Control with AD, DNS."Failed to send DNS query to server 10049".

View 1 Replies View Related

Query A File Has Successfully Been Copied To Destination?

Jan 28, 2013

I wanted to know how, if there are any script which will send an alert once a file has reached a destination over an TCP network.

View 3 Replies View Related

Cisco Switching/Routing :: DNS Query Fails Behind DHCP / NAT - Router ISR 861

Nov 18, 2012

in my simple network setup, I cannot resolve DNS queries from inside my NATted network. On the router I can ping both IP-addresses and names. Ping from the  local machine works for IP-Adresses but not for names. When doing nslookup, addresses are not found and a SERVFAIL  message is returned. I use a Cisco ISR 861 Router to connect our local LAN to the Internet (The WAN of the 861 is connected to another DHCP/NAT-Router, which in turn connects to the ISP-Modem). Addresses in the local LAN are DHCP-distributed, the DNS-Servers from my ISP are configured on the Router and the DNS-Information is distributed correctly to my local LAN machines (as I can verify by doing nslookup on Linux).

View 21 Replies View Related

Cisco Wireless :: WAP200 OID Values To Query For Number Of Stations Associated

Oct 30, 2011

I'm looking at a stack of WAP200 and WAP4410N APs.  I'd like to use Cacti to track number of associations on each AP.What's the OID I should be querying? Are there multiple OIDs that would correspond to the multiple SSIDs?  I'm running 2 SSIDs on all of them, and it would be extra nice to be able to track number of stations on each SSID, though the total number would also be acceptable as well.

View 4 Replies View Related

Failed To Query TCP / IP Internet Connection Settings On Laptop

Dec 14, 2012

I have a Compaq Evo N610c with XP Professional version 2002 SP3 that cannot connect to my internet connection. Has error that failed to query TCP/IP of the connections setting.

View 1 Replies View Related

Cisco WAN :: C3925E Query On Gigabit Ethernet Port - Negotiation Auto

Oct 17, 2012

confirm if "negotiation auto" is supported gigabit port for C3925E router.
Router(config-if)#Interface gi0/2 
Router(config-if)#description test link
 Router(config-if)# no ip address
 Router(config-if)# negotiation auto
% Invalid input detected at '^' marker.

View 5 Replies View Related

Cisco Switching/Routing :: Relay Agent And Forwarding Query On 2960?

Nov 23, 2011

I need support on understanding and configuring dhcp relay agent And forwarding. Lets say a bunch of TCP/IP devices required a dhcp ip where it is installed on a perticular server to run so. The server having dhcp pool where it provide the devices with IP addresses as he recieve queries from them requesting to release their addresses. On 2960 switch no dhcp configured and ports assigned under specific vlan under those devices. The issue here, if power goes down and booting process started, the devices started to ask the server for ip add and it takes too much time and somehow it does not take ip and those request kind a dropped. As the minimum requirement is to configure relay agent on the switch and forwarding and multicast?

View 7 Replies View Related

D-Link DIR-601 :: Router Keeps Making Arp Query To All Ip Addresses In Same Network Periodically

Feb 16, 2013

I found my dir-601 router keeps making arp query to all ip addresses in same network periodically.all dhcp clients are general laptops and smart phone, I don't think there are any arp cheats attack on those it normal?

model: DIR-601
hardware version: B1
firmware version : 2.00NA

View 7 Replies View Related

Cisco Switching/Routing :: 5486 / Mode Conditioning Patch Cable Query

May 6, 2012

I am planning on implementing a mode-conditioning patch solution along with LX/LH SFP's over multimode fiber in my network. I wanted to know if this solution is also supported by the G5486 Gbic's, ie, can I use the 5486 GBIC along with a mode-conditioning patch over multimode fiber as well?

View 2 Replies View Related

Cisco Switches :: SG500-28P SNMP Query For Individual Port Power Output?

Aug 26, 2012

Is there a way to ask the above switch how much power it's supplying to various ports?I've found some stuff in POWER-ETHERNET-MIB, but it's only the main power supply and the up/down status of the various ports.
It looks like what I want is


but my SG500 tells me:

snmpwalk -v2c -cpublic serverswitch
CISCO-SMI::ciscoMgmt.402 = No Such Object available on this agent at this OID

View 6 Replies View Related

Cisco Firewall :: 1811 / Zone-Based Policy Firewall Configuration

May 16, 2011

I have two 1811's connected in a lab using a ipsec vpn tunnel (using a switch to simulate an internet connection between them).I am trying to configure one of the routers as a ZBPF just to allow a remote windows login (DC on the firewalled side, workstations on the other side).I'm trying to verify that the zbpf is working, but it doesn't seem to stop anything.  I had match icmp added to the class-map, but took it out to test if icmp would fail.  It didn't.  Basically, I don't think the firewall is working at all.  Any thoughts on how I can configure this so that the policies will work between zone-pairs?

Here's an quick drawing:

Here are the configurations:

 Local router:
 hostname sdc-1811-LocalLab
no aaa new-model
resource policy


View 11 Replies View Related

Cisco Firewall :: ASA5505 Lose Configuration If Upgrade Firewall

May 17, 2011

i have asa 5505 with the asdm v5.2 (4), and the asa v7.2(4). This platform has a base license. if i upgrade adsm and asa on v6.2(1) and v8.2(2) if I lose my license and that you need to activate them? i configured site to site vpn (this firewall and the another) that i lose my configuration if i upgrade my firewall.

View 2 Replies View Related

Cisco Firewall :: ASA 8.4 What Commands Can Use To Verify Related Configuration On Firewall

Apr 7, 2013

We have an ASA with 8.4(5) version. we had detected that few ip's were getting shunned ,to overcome the problem no shun was used and the traffic normalised.But, the same problem re-occured a few days after that with logs showing traffic being shunned.
is there any fixed way to get rid of this. what commands can i use to verify related configuration on the firewall.

View 3 Replies View Related

Cisco Switching/Routing :: 7010 - Nexus Not Returning FQDN On SNMP SysName Query

Feb 27, 2012

All the other switches / routers on quering for SNMP sysName.0 returns their FQDN in our network. The Nexus 7010 and 5020 switches in the network return only their name. "hostname xx" and "ip domain-name xx" defined on all the devices. The SNMP MIB is matching. There are no other SNMP related issues. How can I get the FQDN for these devices ?
$  snmpget -v 2c -c public m-65k-00.core sysName.0
SNMPv2-MIB::sysName.0 = STRING:
$  snmpget -v 2c -c public m-N7K-00.core sysName.0


View 4 Replies View Related

Cisco Firewall :: Configuration Required For Transparent Firewall ASA 8.2?

Mar 31, 2013

I have one firewall need to be configured in transparent mode. I have inside and outside router. What is the configuration of transparent firewall ASA8.2. I didn't find the configuration on Cisco site.

View 17 Replies View Related

Cisco Firewall :: Transparent Firewall Configuration In PIX 515E

Nov 25, 2012

I am trying to set the PIX firewall to transparent mode.After I set it to transparent firewall, I allowed all icmp, tcp, udp traffics.Currently, any devices in the inside network can get the ip automatically from DHCP server in the outside network but cannot ping to any servers in the outside network either access the internet.Do I need additional confiration on the firewall?
Here's the configuration:
PIX Version 7.0(1)
firewall transparent
interface Ethernet0

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Transparent Firewall Configuration?

Sep 11, 2007

I want to configure an ASA 5505 in transparent mode (7.x). Somehow, I got it to work.. but i need some kind of step by step description. I just want to connect it with outside on a route .. inside in my LAN. Its working now with one ASA. But in the Web Interface the Interfaces inside and outside are down.. but its working.

View 5 Replies View Related

Copyrights 2005-15, All rights reserved