why the following message might appear in my router logs where the 192.168.x.x IP address is a PC on the LAN?*Oct 15 02:24:09.313: %CRYPTO-4-IKMP_NO_SA: IKE message from 192.168.x.x has no SA and is not an initialization offer Do PC's send IKE messages? (its a standard user on Win XP, unlikely any additional VPN software on it).
View 2 RepliesI just got E1000 cisco wireless router. Started setup, everything worked fine and replaced admin password with my own. For some reason got error message. tried to redo setup and got message router not recognized. used laptop and found out that wireless works fine. After few days noticed that there is a (mynetworkname) guest connection you can connect without any password. i don't need that stupid thing and my question is how to disable guest network? I cannot reach Main Menu from cd and have no idea where to look for it when i connect to router by web.
View 9 Replies View RelatedIm getting flooded with the following messages: Feb 14 10:47:19.740 EST: PLATFORM-5-ECC_MSG: A corrected single bit error has occurred in L2C Data Cache at location 0x294.
[Code]...
I am getting a message telling me to install F9K1001 Router Firmware, 1.00.12. It lists 6 changes since 1.00.08. I just want to make sure this is not a virus and that it's legit before I install it!
View 1 Replies View Relatedi have 2851 router and it is hanging when i login on it while it is hanging it gives me the following error message: [code]
View 2 Replies View RelatedI know that the routers communicates using routing protocols and that they forward the ip packets. So I looked in the IP header and the RIP header(for example) and I don`t understands when an packet comes in how does the router understands it`s type? (There`s no byte field to tell him explicitly that this is an ip packet or a rip message)
View 9 Replies View RelatedI have strange problem with 1800 router , I can't see any debug messaging , the ping from PC to this router is Ok , but no icmp debug appears , even I enable "debug ip icmp " the version of router is : C181X Software (C181X-ADVENTERPRISEK9-M), Version 12.4(6)T6
View 2 Replies View RelatedI am trying to set up a E2500 router to a Arris/Comcast modem. I connected the blue cable to the router then to the modem and followed the Cisco instructions on the disk. I was 90% done when I received a error message 82BD0118 - Description - adapter connection time out period expired with no IP address.
View 2 Replies View RelatedWhen I try to copy ios to one flash in router 2801, I receive the message of of insufficient memory, and have the follow out in the next command: [code] This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
View 6 Replies View RelatedI recently bought the E2500 Router and I am using the EA2500 Adapter with it . I have this set-up on 2 Desktop PC's . 1 Pc is working just fine with this set-up . The other keeps giving me an Error message of "Invalid Key Manual" . What does this mean ? The adapter is working because it does find the Router as a usable connection . It just isn't able to connect to it and keeps giving me the same Error message .
View 8 Replies View RelatedMy WRT54G router is already feeding 2 wireless PC's with no problem. Haven't been as successful getting my new Samsung Series 7 TV wireless connection working. The TV screen prompts for a 'security key', but once entered, tells me the connection is unsuccessful. The TV does not provide any specific error message - just tells me to re-enter the security key and/or re-start the router (which I have done many times with no success). I am entering the 'Encryption key' from the WRT54G router when prompted by the Samsung TV for the 'security key'.
View 2 Replies View RelatedIs there I can customize the error page which is shown when someone visits a blocked site
View 3 Replies View RelatedI just bought a E4200, is there a way change the default text of the pop up message that is used when the client is requested to put in the password to access the guest SID for the e4200?
View 2 Replies View RelatedWhen i try to connect kf to wifi router, I keep getting password error message when I type my network pw. I have no problem connecting to other wifi connections
View 6 Replies View RelatedWhen i connect the Router 2821 through the Consol get error message at regular interval of time %ENVMON-4-FAN_LOW_RPM: Fan 1 service recommended.
View 2 Replies View RelatedI have a Netgear WNR612 wireless router, which worked fine for a few weeks. Then something happened and I can't keep the connection anymore. It happened right after I used iTunes to update my iPhone, perhaps a coincidence, but I'm mentioning that just in case. Internet still works fine with ethernet cable straight from the computer, only the wireless connection doesn't work. This happened about a month ago and I haven't been at home much to fix the problem. I have turned off and unplugged everything for several days at a time while gone. I get a Network Error message saying, Windows has detected an IP address conflict. I have tried restoring the router back to factory settings and reinstalling the wireless card. I have tried changing the IP address settings both in the Network and Sharing Center and the router admin page. What I think I should do is change the IP address in Command Prompt, but when I type "ipconfig /release", it says "No operation can be performed on Wireless Network Connection 2 while it has its media disconnected" and the same for Local Area Connection. I don't understand what this means, because there is a wireless key in my keyboard and there is a white light (not orange) like there should be. Also in the Network and Sharing Center, I can see that the connections are enabled.
View 14 Replies View RelatedWe are currently trying to installed LMS 4.0 on a VM Ware instance of Windows 2008r2, and getting the error "cannot run name lookup" message when launching the installation. We are launching the Win2008 patch and it asks for the desination of the LMS application then spits out this message.
View 10 Replies View RelatedThe message ID I can use to filter VPN clients connecting and disconnecting from the Firewall?
View 1 Replies View RelatedI’m deploying new images on my switch 2960 24TT L. After installing the new image (c2960-lanbasek9-mz.122-58.SE1.bin) and reboot the switch I have always this error message : “Error loading "c2960-lanbasek9-mz.122-58.SE1.bin"
Interrupt within 5 seconds to abort boot process.
Loading "flash:/c2960-lanbasek9-mz.122-58.SE1.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ”
But the switch still boot well. Why do I have this error message?
Need to clarify this log message:
*Oct 23 06:20:07 UTC: %FPD_MGMT-3-INCOMP_IMG_VER: Incompatible ROMMON (FPD ID=5) image version detected for 7600-SIP-200 card in slot Detected version = 1.3, minimum required version = 1.4. Current HW version = 2.303.
In Soft Apliance 4.2.2 I keep up getting diskWatcher Available space message:
It is fresh installation:
[LMS-500/root-ade ~]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/smosvg-usrvol
[Code].....
I received a syslog message on my cisco 3845 router, what is that message mean. 11 13:36:06.265 UTC: ASSERTION FAILED: file "../les/if_ng_dslsar_tx.c", line 385
View 2 Replies View RelatedI have installed LMS 4.0, installed the 2008 R2 patch as well. Everything worked with SSL until I did an import from our 3.2 Solaris version. After that, now when I access the application I get a message:
"Forbidden You don't have permission to access / Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request"
I have recreated the certs, reset the casuser, verified the correct prvilieges were set for casuser.
if the notification that the pw will expire in xx days works in the scenario named in the headline? Anyconnect SSL-VPN (ver 3.1.xxx) terminating on ASA 5510, v 8.4.4, authentication: Radius to ACS 5.3 (over MSChapV2), IdentityStore: MS ActiveDirectory. the Password-Change (if the pw is set to "change at next Logon") is working, even if there is a Bug, too (on the ac-client).
In the tunnel-group password-manegement is enabled and notify is set to the default of 14 days.does the ACS interrupt the notification? I can't see any message in ACS Log or in "debug aaa common 255" or "debug radius" on ASA.
I'm seeing a lot of these message in my 5520 ASA.
Deny IP spoof from (0.1.0.4) to 0.1.0.4 on interface inside
LMS installed on Windows 2003. Backup fais with message "Backup failed.ERROR(1297): Fatal error: Database engine 'UPMDbEngine' could not be started on database 'upm' in Bulk mode.."
dbbackup.log attached.
I'd like to know if it's possible to change the system message for each ephone independently with CME ?I mean, changing an ephone's system message without changing others' ones.
View 3 Replies View RelatedI was wondering what could cause this, because every time this message shows up in the log I lose internet connection for about 1 minute then it comes back up. Let me know if I need to get any config info.
View 8 Replies View Relatedthis message is flashing again and again after 2 sec
IP-EIGRP(default-ip-routing-table:1) neighbour XYZ is not on common subnet for serial0/0 ?
We have a ASA5540 and we would like to shutdown the VPN service. To do so, we would like to warn people by sending a message prompt when they logged in using Anyconnect. Message are only working on DA that terminate but not on those who Continue. I have also tried the Checkandmsg fonction but it behave the same way.
View 2 Replies View Relatedtying to connect CSM client to CSM server (ver 4.0) and getting attached error message. The server is running, no errors reported while installation, all services are up and fine. I tried to install client locally on the server and connect it that way with no luck. CSM server runs on Win 2008, firewall disabled.
View 0 Replies View RelatedAs soon as I connected my ASR 1002s to the Internet and digested the Internet BGP table, I began receiving this message. I’ve google’d and turned up nothing so far. I assume I need to allocate more memory to this process.
%PLATFORM-4-ELEMENT_WARNING: R0/0: smand: ESP/0: Committed Memory value 312% exceeds warning level 310%
Here's a sh mem:
#sh mem Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)Processor 3008A008 1758530508 647878488 1110652020 1110104020 1109994164lsmpi_io 98FEB1D0 6295088 6294120 968 968 968
I am getting the message '400 bad request' whenever I try to backup the configuration or export a certificate under Certificate Management.
View 1 Replies View Related