Cisco Routers :: RV016 With 3 WAN Connections - Windows Messenger Intermittent
Nov 9, 2009
I have a RV016 Router with 3 internet DSL conections.
Firmware version : 3.0.0.1-tm (Jun 6 2008 20:17:06)LAN IP : 192.168.11.254 /24WAN1 IP : 192.168.1.253 /24WAN2 IP : 192.168.2.253 /24WAN3 IP : 192.168.3.253 /24MODE: Gateway.
Windows Messenger continually connects and disconnects. This behavior is permanent I only have problems with Messengers (all releases), web page access is correct. I check bandwith saturation and It's ok, I use less than 50% of each DSL. I configured the correct size of MTU for each DSL and the problem continues.Is there any way to set priority to this service? Is there any way to check if the "load balance mode" affect this kind of connections?
View 12 Replies
ADVERTISEMENT
Oct 14, 2011
I am getting crazy with our Cisco Linksys RV016. It handles 3 simultaneous connections to the internet using 3 ISP. All our company goes to the internet using this cisco linksys RV016, our corporate switches are connected as clients to the router. Sometime ago, this router started to drop POP3 connections to our network, when this problems is present, all users get Receiving' reported error (0x80042108) in Outlook 2007-2010. Currently i have setup POP3 service to use the First ISP connection, but when this problem is present, the only way to eventually resolve it is to switch the link POP3 Service from the First to the Third ISP, sometimes it works immediately, sometimes don't. We are using this router since 2007 but this problems started to arise from this month.
Our switch is the latest firmware available is Cisco website, this is the Firmware Version: 3.0.2.01-tm.
View 5 Replies
View Related
Feb 28, 2012
We have a RV016 load balancing between two broadband WAN connections. On protocols that are sensitive to a change in IP address such as ssh and https, if the client connection goes inactive for a short time (sometimes as short as 10 seconds), the RV016 often changes WAN connection as part of its "load balancing" feature. Most protocols do not even notice, but the more sensitive protocols do and often lock a session or timeout the session which is not a good thing.
We have been able to bind these sensitive protcolols to a particular WAN port but (in our minds) this is not an "ideal" situation. In fact I would consider this to be a broken "load balancing" solution and should be fixed.
View 7 Replies
View Related
Sep 19, 2011
My windows messenger wants confirmation on password. Everytime I try it takes me to my old live.ca account to confirm instead of my fairly new hotmail account.
View 1 Replies
View Related
Jul 27, 2012
[code] When the connection is online, the speeds are fine- the issue is the 2-3 times a day when the connection drops off. The error that we are getting is "cannot connect with primary dns server" however in our attempts to restore the connection we have: [code] is there some issues in the area that we are not aware of?
View 3 Replies
View Related
Sep 25, 2012
V1.03 fw. My connection stays alive, and does not loose connection but I cannot access web pages and my qnap NAS download just go to 0.After 5 mins they are all back up to speed and then drops again to zero.Getting very fusrtated with the x3000. Had the WAG160n but that kept overheating.The x3000 is this an overheating issues?
View 1 Replies
View Related
Feb 2, 2012
Can't connect me windows live messenger
View 1 Replies
View Related
Jun 29, 2012
I'm trying to block any access to Windows Live Messenger. Domain names, Ip addresses or somethings that I can use to stop users from logging in?
View 2 Replies
View Related
Dec 23, 2011
I have a wireless router Linksys WAG200G.Im having trouble since a few days for use Windows Live Messenger 2009. I tried some tips for correct (cleaned cache, uninstall and re-install the software, checked the firewall, programs related to the software, etc).I was thinking that this was a trouble with my computer, but was made tests with other 3 computers, that cannot connect too (and can connect in others wi-fi connections, in other places) and in the attempts are being generated the same error: 8100030d.Searching in the internet, i saw that the problem could be with the router.
I didnt made any changes in the router configuration, and are using this equipment since last 2 years without any problem. I didnt tried to reset the configuration yet. But tried to disable the router firewall, and the problem occurred again.I tried some tips in this forum, like changing the MTU and including ports of messenger in the router configuration, but it didnt work.
View 3 Replies
View Related
Jan 17, 2011
I have internet connections and i use Firefox now instead of Internet Explorer but whenever i want to sign in the Windows Live Messenger or Yahoo, it won't let me because it says the network is not connected. I used to be able to, even when i have Firefox. I check to see if the network is connected and it always is.
View 7 Replies
View Related
Feb 6, 2011
why would you block my use of yahoo messenger
View 1 Replies
View Related
Sep 26, 2012
We are still using some old WRV54G wireless VPN routers for work. Can we get new vpn software that will work with these routers? The quickvpn client software we have no longer works after we last updated the firmware. How can we set up vpn connections using tunneling?
View 1 Replies
View Related
Jul 24, 2012
We have a newly-purchased RVS4000 v2 with firmware v2.0.2.7. Its intended role is as a gateway between our local network of wired workstations and a Cisco 2800 series Integrated Services Router, which is at the receiving end of our T1 line. It is configured with static IPs on both the LAN and the WAN side. It does NOT serve DHCP for the LAN. Ever since I installed it, I have had repeated complaints from users of Vista and Win7 workstations that they lose internet connectivity about every 20 - 30 minutes or so. The only solution is to unplug the workstation's CAT5 cable, count to 30, and plug it back in. Then everything's hunky dory for another 20 - 30 minutes. Meanwhile, all our Windows XP and Linux workstations enjoy uninterrupted internet access. The router/gateway we replaced (a DLink DIR-130) never had this problem.
View 4 Replies
View Related
Jun 2, 2012
I have frequent intermittent 105 errors DNS Server not found. I run a Laptop, Win7 home edition 64 bit, Telstra TEHS_0c280c 3G usb Modem, I live 600 metres from Repeater and have consistant full WiFi strength. I have had this error using both Google Chrome and Internet Explorer.
When this error locks me out of the net, it is very frustrating as I have to reboot the laptop and reset the WiFi modem several times before the problem comes good. Sometimes this can take up to a full day as I can get the Net back and then have the 105 error again, and other days I will not see it at all.
Remedies I have already tried to no avail :- CCleaner to both remove cookies and clean and repair registry probs. And Defragging.
View 4 Replies
View Related
Jul 1, 2011
I just built a new computer running Windows 7 with an Intel 82579V Gigabit on the motherboard. Since last night while playing an online game, I have occasionally noticed sudden network failures where I either time out of my game or severely lag for 10 seconds before the game catches up.
My other network hardware and setup remains unchanged during this build.I have never had issues with my internet connectivity from my ISP.
The problem is not consistent and I'm not sure how to repeat it. I was playing my online game for several hours and then suddenly started having problems every 5 minutes with disconnecting.I can watch the network utilization in the Windows Task manager drop suddenly and then spike back when I reconnect to the game. Similar visual seen on the Tomato software on my router.
So far I've grabbed the latest drivers for the network chip from my motherboard manufacturer's website and turned off Teredo. I also made sure no power saving features were enabled on the network chip in the device manager.
View 1 Replies
View Related
Oct 7, 2012
I have looked through the forum for answers to my problem, but does not look like I'll find it.The problem: Router randomly freezes.When this happens:No IP/DNS,No response to ping,No contact at all (wifi or cable),Works fine after reboot for some time.
View 2 Replies
View Related
Jan 27, 2013
I would like to ask if what is the replacement for RV016? Is there any on the ISR G2 that can be set as a mulit-WAN router? Meaning can handle for more than two WAN connections.
View 2 Replies
View Related
Jan 22, 2010
I have a rv016 that's been in 24x7 operation since I bought it a few years back. It is out of warranty. It is connected to three cable modems on WANs 1-3. Behind it are a bunch of PCs getting IPs via DHCP. There is a gateway to gateway vpn tunnel setup on wan3 to a rv082 at another site. There is a forwarding entry for http to an internal http server. Everything else is pretty much default.
The router is primarily used to aggregate bandwidth for uploading large numbers of photos. The systems behind the router initiate the uploads and the router automatically load balances the outgoing bandwidth.
This was all working fine until just recently. The ISP is Knology who is upgrading each of the 8m/768k cable modems to 25m/5m. They are also moving from DOCSIS 1 to DOCSIS 3. They are currently in the middle of this upgrade and have upgraded the modems to DOCSIS 3 as well as the speeds to 12m/2m. The problem is that the rv016 Network Service Detection, which is set to "Default Gateway" indicates that the modems fail randomly. Usually only one will be failed, but up to two will fail the Network Service Detection simultaneously.
Knology insists that there is nothing wrong with their modems. I have removed a modem from the rv016 when Network Service Detection indicates it is in a failed state and connected it directly to a computer. It will work, but it has a different IP address and default gateway. As soon as I connect it back to the rv016, it works there too, but on the original IP address and gateway. I've only tried this test this twice so far, so it is a bit inconclusive.
Speed tests behind the rv016 are the same as directly connected to one of the cable modems. The router works normally as it has for years. Nothing else is acting funny.
So my question is, is the rv016 failing or is the ISP having problems?
View 17 Replies
View Related
Jul 22, 2012
Problems on RV016 the firmware, Firmware Version : v4.2.1.02 (Jan 18 2012 14:10:55) on port PPPoE mode. It makes the dial, but not Web browsing correctly. The solution was to return the old version of firmware.
View 1 Replies
View Related
Nov 22, 2011
I am trying to upgrade my RV016 from 3.0.2.01-tm to 4.0.4.02. I have not received any messages and the log has nothing. I have left the computer and switch for 2 hours and it never seems to end. (serial no. DF0006200812).
View 1 Replies
View Related
Dec 28, 2011
Is it possible to have this setup on RV016?
WAN1: VOIP traffic (either by port or IP) + failover for WAN 2 WAN2: all other traffic + failover for WAN1 WAN3: failover for WAN1 & WAN2 with connection on demand
View 0 Replies
View Related
Jul 16, 2012
I have hardware version 2 and firmware 3.0.2.01 (latest firmware available for this hardware version I believe) and I cannot get it to email me logs. I have entered my outlook address and our SMTP server.The log says that it's failing each time it attempts. I have scoured the internet and I cannot find a solution that will work for me. I have found some talk of adjusting an MTU setting which is supposed to be located under the firewall / general tab.
View 1 Replies
View Related
Feb 22, 2012
this router (RV016v3, Firmware: v4.1.1.01-sp (Dec 6 2011 20:03:18)) in regards to it not properly directing UDP packets out of the right WAN, as per the settings stored in Protocol Binding section of [System Management, Multi-WAN].I use the section to direct all traffic from desktop computers (192.168.5.100 ~ 192.168.5.199) through WAN4, and all VoIP related traffic (192.168.5.200 ~ 192.168.5.239) through WAN2(PPPoE).Everything seems to be working well except for some of the UDP traffic from 192.168.5.200 which is seen in the log going out of WAN4 instead of WAN2.I have even created a new entry for [UDP/5060~5060]->192.168.5.200~192.168.5.200(0.0.0.0~255.255.255.255)WAN2, and placed it at the very top of the list.Here are a few lines that I've observed in the log: (Refreshed the registration of two SIP Trunks configured in our PBX)
Feb 23 18:11:47 2012 Connection Accepted UDP 192.168.5.200:5060->184.72.227.214:5060 on eth4
Feb 23 18:11:46 2012 Connection Accepted UDP 192.168.5.200:5060->50.56.59.168:5060 on ppp2
Feb 23 18:11:46 2012 Connection Accepted UDP 192.168.5.200:5060->184.72.227.214:5060 on eth4
Feb 23 18:11:46 2012 Connection Accepted UDP 192.168.5.200:5060->50.56.59.168:5060 on ppp2
There are no static routes configured, so i'm baffled by what could cause some of the UDP packets to go through the wrong WAN.All TCP Traffic from 192.168.5.200 is seen going though WAN2 as it should.
View 2 Replies
View Related
Nov 3, 2010
Would one of the 'Cisco RV016' work with a switch? I'm planning on running our work network using this device to load balance between 3 WAN connections and would like to keep the upstairs and downstairs computer users separated via a switch.Will the switch affect the load balancing or will the router still be able to detect each individual user and balance the load as seen necessary?
View 7 Replies
View Related
Oct 19, 2011
We are deploying a new batch of RV016 with the latest firmware (4.0.4.02). We are using 3 WAN ports for internet access (WAN1, WAN2, WAN3)The WAN ports connects to Cicso 800 series adsl modem with DHCP.The RV016 WAN1 port setting regularly resets to 0.0.0.0 despite that the modem dhcp is still up and running. A cold boot, resets all the configuration and WAN1 port start working againg a new ip.
All three WAN ports are set to automatically obtain ip from the modems.We have tried several modems, and even swap WAN ports, but the error is persistant to WAN1 only.
WAN2 and WAN3 are up and running without any errors. This error is persistant with WAN1 only.We have also configured a manual ip on WAN1, and after a few hours of operation on all 3 ports, traffic on WAN1 comes to a halt.We have the same error on 3 units we received last week.All there modem are configure on different subnets.It does not seems to be a configuration error with the modem as they work perfectly well with the WAN2, WAN3 ports.We also tested a RV016 out of the box using the wizard setup, without any extra setting/configuration, and we got the same error after a few hours of operation.
View 1 Replies
View Related
Jan 10, 2013
I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1
View 5 Replies
View Related
Jan 14, 2013
I know this is a small business appliance I got my ccna certification with the hope of practice my CLI skills with a cisco device however I read in cisco docs the small business routers doesn´t support talnet neiter ssh I mean CLI, is thta true ?
View 1 Replies
View Related
Mar 31, 2011
I have two LANs 192.168.0.* and 192.168.1.* (main)
I'd like to facilitate port forwarding on the sub-LAN - is there a way to configure the device to do so? The "main" LANs fowarding works just fine, however I have specific ports that need to go to the sub-LAN.
View 3 Replies
View Related
Aug 15, 2011
I have a RV016 with an internal address of 192.168.1.1. Also on the 192.168.1.0 network is a gateway server that the rest of my clients sit behind. The clients are on a 172.16.3.0/24 network. All of the gateway server does is forward the packets. It does not NAT. There is a static route to 172.16.3.0 on the RV016.
So my question is how do I get traffic from 172.16.3.0 to route through the RV016? Computers on the sub net can ping the RV016 and get a reply so I know the gateway server is forwarding the packets between the two sub nets just fine and that the static route on the RV016 works. Any traffic that tries to go beyond the RV016 never makes it. It just disappears at the RV016. I have checked all of the ACLs and they should let all internal traffic through.
View 3 Replies
View Related
Sep 5, 2011
I have 11 available IPs at a data center and have 5 servers I want configure - each with its own LAN, not to be networked together (used for web, ftp, sql and other webs services). Is it possible to configure the RV016 with 5 WANS, each attached to a specific port with its own LAN?
Am this even the right considerations for this router as I would just have normally purchased 5 routers and attached them individually to each server with their own specific WAN and LAN?
View 2 Replies
View Related
Nov 26, 2011
I just purchased a RV016 router, upgrading from an older Linksys router only to find out that there was no support for TZO DDNS. I have used TZO for years now and don't really want to change to another service. Any way to request this from Cisco engineers for future firmware upgrades?
View 2 Replies
View Related
May 29, 2013
i go to setup/port forwarding and it has every port except port 22 available to forward. what's up with that?
View 1 Replies
View Related
Aug 5, 2011
I recently replaced RV016 with a new one. Now I'm having connectivity issues with my server. One particular software I'm running on workstations will no longer connect. Everything is set up the same as with the old RV016. Internet connection is fine.
Based on the tech support from the software company, they are saying - "The clients contact the server using the HTTP protocol and the server IP address or host name. You should begin troubleshooting by pinging the server from the workstations to see if they have any connectivity to the server and move forward based on the result of that ping." Pinging the server from the workstations results in timing out.
View 1 Replies
View Related
