Cisco Switching/Routing :: 3560 - Move Html Folder From Subfolder To Root?
Nov 13, 2012
I have a cisco 3560 8 port switch. I really would lime to have the webinterface enabled. So i downloaded the archive from cisco. I extracted the archive to the flash of the switch. After rebooting the device everythings looks fine, but the html folder is a subfolder. It looks something like this: flash:c3560.../htmlI my understanding to enable the webinterface the html folder should be here flash:htmlHow do i move the html folder from the subfolder to the root?
View 1 Replies
ADVERTISEMENT
Mar 16, 2011
I have redirected the IE Favorites folder to our network but I need a script to copy the Favorites to the new location.
View 2 Replies
View Related
May 14, 2011
I have a Windows 2003 SP2 server with a shared folder. This folder is accessed by 2 people on a regular basis. The problem we are experiencing is when a folder is created by user A, it cannot be moved by user B (and vice versa), as it says the folder is in use.The exact error is: Error Moving File or Folder.Cannot move <filename>: Access is denied.Make sure the disk is not full or write-protected and that the file is not currently in use.I have explicitly set full control for both users on the folder. The drive has 70GB of 500GB remaining. I have also used File Server Management to verify the files were not in use when they were being moved.The server is Windows 2003, SP2. Domain environment, with all relevant users having permissions on the folder, and the everyone account removed. Any other operation inside the shared folder works fine.
View 2 Replies
View Related
Oct 16, 2012
I have a setup where - I have a cisco stack (4X SGE2010 Switches) trunking over to a 3COM switch. Both switches believe to be the "ROOT" of the network. Note The 3COM is running RSTP as opposed to the Cisco Stack which is running normal STP. To my understanding of STP - Essentially STP is not functioning! Both switches believe to be the "ROOT" so they don't shut ports down. (We are currently having major issues with ports going up and down for seconds at a time on both switches)
View 3 Replies
View Related
Feb 16, 2013
I config vlans 21-23 on 3750 A and B switches.I config B switch to be Root Bridge for all vlansspanning-tree vlan 1,21-23, priority 4096 sh span tree on B switch 3750B# sh spanning-tree.
View 18 Replies
View Related
Feb 11, 2013
I have two 6509s both with single FWSMs running in transparent mode with bridged Inside and Outside VLANs.I have my Core A set to STP priority of 8192 and Core B set to 16,384 to make Core A the root for all VLANs.Problem I have is when I look at spanning-tree on Core A for Inside VLAN 324 it states to get to the Root go via PO100 (Cost of 9) and that the Root also has a Priority of 8192, but as the designated Root has a lower MAC address it's pointing to the etherchannel. PO100 is L2 Etherchannel between the Cores.Moving accross PO100 to Core B and running the show spanning-tree command I can see that to get to the Root Bridge I need to go via PO272. PO272 is the internal Etherchannel to get to the FWSM on the Core B Switch. This shows a cost of 6 to get to the Root and a mac address of the Root Bridge which resides on Core A (Outside VLAN 124)To give some perspectibe,theoutside VLAN of the pair has it's STP ROOT on the Core A switch as intended?
View 1 Replies
View Related
Jan 18, 2012
I have an Extremely Old switch that I need to connect to my network. Because it is so old I don't want it to become the Root Switch.
what is the command to change the priority. (Honestly I don't remember if it has to be a lower number 1 or a higher number ). Always get that mixed up. I've read about root guard, but I would like to prevent it manually. (It is a small network after all)It is a Cisco 2950.
View 3 Replies
View Related
Jan 12, 2012
I have 2 3550 12G switches that I use as core fiber switches. Switch 1 is the primary for 1/2 the V LANs and Switch 2 is the primary for the others using MST with 2 instances (I am not including the default 0 instance). I am using HSRP to provide redundancy. So far so good.
Recently a tenant in my building would like to use their own switch for data but still needs access to a V LAN on mine for voice. Again not a problem as I can configure a trunk port and give them what they need. My concern is that if they try to configure STP on their switch can they take down mine. Are there some preventions that I can put into place, such as root guard, that work with MST? What happens if they too set up MST can they kill mine?
Switch 1 is the root for 1/2 the v lans and Switch 2 is the backup root. The scenario is flipped for the other 1/2.
View 3 Replies
View Related
Apr 1, 2013
I have two locations DC and Corp connected to each other via Point to Point Circuit. I have forced the two core switches setup as GLBP pair to be primary and secondary for certain VLAN's including VLAN1.I have a switch in our Corporate office 3750 which is where the point to point circuit terminates. VLAN1 SVI is manually shut on that switch. Also the priority on VLAN1 is increased manually like this, "spanning-tree vlan 1 priority 28672".
Now the issue is that the Primarey Root Bridge in the DC is the root bridge for VLAN 1. But this other switch 3750 in our corporate office also is a root bridge for VLAN1. [code]
View 17 Replies
View Related
Dec 15, 2012
in my LAN the all access layer switchs/stacks are connected directly to core backbone switch (cisco 6509) via sfp fiber-optic, i want to protect my spanning tree setup with the "root guard" command.
1. where would i set this ? on uplink ports on access layer switches ? or on core backbone ports to which the access layer swithes connect to?.
2. can this be set on active (production) ports without downtime?
View 5 Replies
View Related
May 3, 2013
We have a problem with a Cisco 1400 Bridge. This equipment can not bridge to the other root or not root mode. I can see a message "Interface Dot11Radio0 Radio transmit power out of range" and the MAC Address of Dot11Radio0 appears with 0000.0000.0000.I set the local power to 18 but the MAC Address is still in 0000.0000.0000.
View 1 Replies
View Related
Oct 18, 2011
i got the problem with 1300 bridges,root bridge with omni antenna and non root with sector antenna , it can associate and can pin each other , but whenever i try to browse several web pages its get timed out and radio was down.
View 5 Replies
View Related
Jul 18, 2011
Any working configuration between two BR1310's in Root/Non-root mode? The documentation is vary vague and i can't find anything more secure than WEP. Is it possible to use WPA with radius authentication?
View 1 Replies
View Related
Apr 19, 2012
Cisco 3560 does not support "set ip next-hop verify-availabilty". I need this command in my config. "set ip next-hop" do not do the same job.
View 8 Replies
View Related
Dec 8, 2011
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
View 4 Replies
View Related
May 8, 2012
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
View 9 Replies
View Related
Apr 17, 2012
I have tried to make policy based routing on Cisco 3560. I use ipservices ios (SW version 12.2.(50)SE3 and SW-IMAGE C3560-IPSERVICESK9-M) For below configuration there is no problem and pbr is working.
“Access-list 100 permit ip host 1.1.1.1 host 2.2.2.2
Access-list 101 permit ip host 1.1.1.1 host 3.3.3.3
Route-map pbr1 permit 10
Match ip address 100
Set ip next-hop verify-availability 1.1.1.2 1 track 11
interface fasthethernet 0/1
ip policy route-map pbr1”
But when i add another sequence to the "pbr1" with another sequence number like that.
“Route-map pbr1 permit 11
Match ip address 101
Set ip next-hop verify-availability 1.1.1.3 1 track 12”
pbr is not working. Switch gives message "PLATFORM_PBR-3-UNSUPPORTTED_RMP:Route-map pbr1 not supported for Policy Based Routing”"ip policy route-map pbr1" command not shown in the running config. And "show ip policy" output is blank.Configuration guide says you have insert many sequence to the route-map with the same name. And also this command is not in the unsupported command list.
View 16 Replies
View Related
Jun 4, 2013
I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
View 3 Replies
View Related
Dec 11, 2012
I implemented access list on cisco 3560 switch but it never works. I want to block access from network B to Network A and allow from Ato B
Network A. 10.0.12.0/24
Network B 10.0.24.0/24
The configuration is
interface Vlan1
description Data VLAN
[Code].....
View 14 Replies
View Related
Apr 28, 2012
We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing. We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.
View 17 Replies
View Related
Apr 24, 2012
Can I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies
View Related
Feb 25, 2013
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
View 4 Replies
View Related
Oct 21, 2012
I have a 2504 WLC connected to a Catalyst 3560 which has multiple vlans and is connected to a 2800 series router. I know the catalyst is L3 but I am needing nat functions to get outside to the internet. From my 2800 series router I am able to ping out to the internet, also I am able to ping the vlan interfaces on the catalyst switch. Problem is from the catalyst switch I can ping the inside and outside address of the 2800 but I cannot get any further then that. I cannot ping the 2800 router gateway. Not sure what I am doing wrong as far as routing.
I've attached my 2800 and 3560 configs.
View 3 Replies
View Related
Oct 7, 2012
I am trying to upgrade the IOS in 3560 but I am facing one issue. Its flash is 15MB & available space is 8MB whereas the IOS is of 11MB. How can I upgrade the IOS without upgrading the flash?
View 4 Replies
View Related
Mar 10, 2013
We bought a 3560 PoE switch to replace tons of PoE-injectors but when connecting the devices our logs were flooded with
Mar 11 15:09:20.725: %ILPOWER-7-DETECT: Interface Fa0/7: Power Device detected: IEEE PD
Mar 11 15:09:20.725: %ILPOWER-5-INVALID_IEEE_CLASS: Interface Fa0/7: has detected invalid IEEE class: 7 device. Power denied
Mar 11 15:09:20.968: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state to down
Mar 11 15:09:20.985: %ILPOWER-7-DETECT: Interface Fa0/7: Power Device detected: IEEE PD
Mar 11 15:09:20.985: %ILPOWER-5-INVALID_IEEE_CLASS: Interface Fa0/7: has detected invalid IEEE class: 7 device. Power denied
While the message seems quite clear im wondering if there's any workaround on the problem?
View 13 Replies
View Related
Jun 6, 2013
I have a Cisco SW ( 3560 ) with one Trunk link to my router ( 7606 ), Trunk link is fully utilized so i need to add 2nd Trunk.Shall all move some customers from old trunk to 2nd one and create a new subterface for them ?I am think if i can create bundle and add subinterfaces under this bundle ?Add two GE ports to be memeber of this bundle ?
View 5 Replies
View Related
Oct 28, 2012
We have a IP-phone system connected to port 1 on a 3560 switch, the phone system tags traffic with dscp. The switch uplink is on port 24.
Is this configuration correct:
interface 1:
auto qos trust
interface 24:
priority-queue out
View 3 Replies
View Related
Nov 21, 2012
I have a 3560, which is being used as our core router that I have recently installed. It still has the standard IOS which came with (C3560E-UNIVERSALK9-M) it but I need to implement policy based routing so need to upgrade it and have downloaded c3560-ipservicesk9-mz.122-58.SE2.bin and indeally would like to install it in the morning before people start work.
I have 2 questions, 1, Is the ipservices capable of PBR as I have been reading conflicting reports, in fact my friend who works for Cisco has advised that it is not possible on the 3560.
2, When I do upgrade will there be any current configurations that are not compatible with the new one, I wouldnt image that there would be any but just wanted to make sure as it would be the biggest headache ever if it went wrong.
View 7 Replies
View Related
Nov 23, 2011
I configured following command to implement QoS on Cisco 3560.
class-map match-any IND
match access-group name Lync
policy-map LyncAV
class IND
set ip precedence 4
[code]....
how to apply this QoS on interface?
View 3 Replies
View Related
Jul 29, 2012
I have a 3560 POE that will no longer boot and I am not able to load a fresh copy of software onto it. It appears that it has lost all data. When I attempt to TFTP a new IOS, I receive that following error:
Transfer cancelled by remote system
I have tried using dir flash: to see what is contained in the flash directory but I receive the below message:
unable to stat flash/: no such device
I am stuck in rommon mode so when I do switch: dir command, I don't even see flash as being a filesystem. The below list are the only systems registered.
bsdcs[0]: (read-only)
bstage[1]: (read-only)
fstage[2]: (read-write)
xmodem[3]: (read-only)
null[4]: (read-write)
tftp[5]: (read-only)
Is this switch finished or is there something else I could try?
View 8 Replies
View Related
Jun 5, 2012
I have issue with 3560 switch QoS configuration . I checked in cisco site about mentioned model QoS configuration.once we mark the frame and map the CoS to DSCP and once it enters into switch and it processes according to LAN QoS configured on interface
we have configured both the commands shape and share.
once it leaves the switch and enters into Edge router and if we do not have configured QoS in router which is normally MQC , how does it process each packet ?Do we need to have end to end QoS configured in LAN ?
View 5 Replies
View Related
Mar 17, 2013
I found that when I enabled layer 2 auto QoS in 3560 switch, I need to wait so much time to open a file in network drive. Howerver, when I disable the Qos. It can improve a lot. I have used a sniffer to capture the packet to see. Those default packet is in DSCP 0. Therefore, I think majority packet will drop to queue 4. How can I increase the buffer and threshold in order to improve queue 4 performance.
View 1 Replies
View Related
May 12, 2013
We have two L3 3560's. One 3560 has an upstream MPLS router. The other 3560 has an upstream backup VPN router. Both of these 3560's are L3 switches with IP routing enabled. I created a PBR on both so that specific traffic routes through the MPLS router, while other traffic routes over the backup VPN router. I'm trying to apply the PBR to the SVI's, on each switch. However, when I do a "sh run", the PBR does not appear under either SVI. I've enabled the SDM Routing template, made sure that ip routing was enabled, and even verified that the IOS has the capability. Not sure what else to check for.
View 8 Replies
View Related
