I have a RSPAN session configured between a Cisco 3750 and Cisco 2950 switches and I dont see the traffic I am expecting to see on the destination port. I only see broadcast traffic .. HRSP hellos etc. Below is what I have configured on both switches.
the phone connects to the 3750-A access layer switch (VTP mode client) which connects to the nexus 5596 (The nexus is the layer 3 device and set to vtp mode server) and finally we have a Voice recorder that connects to another access layer 3750-B switch.(VTP mode client)
For voice recording I need to setup RSPAN and the nexus5596 does not support RSPAN will the following have any impact on the nexus
IF I move the 3750-B to VTP server mode and run the command remote span on the VLan I need to Rspan its going to update the VTP data base in short it will update the vlan.dat file for all the switch in that VTP domain.
AS the vtp update reaches the nexus saying there is a change (keeping in mind the nexus does not support rspan not sure hows its going to handle that request and how its going to update its vlan.dat file)
Is it going to incremment the VTP revision number? can it crash the vlan.dat file on the nexus ? or do nothing and ignore the update and stop the update from proceeding to the 3750 A switch?
I am aware that the 3750 switches are not able to support Netflows, so I have created a SPAN port and spanning traffic from a specific port. I would like to create a seperate VLAN and trunk the traffic from the SPAN port down to the 6509 switch and then capture all the traffic for that VLAN on the 6509.
we are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950 S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end 3750 SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
I am trying to connect a cisco catalyst 3750g-48ts with our exsiting 3com corebuilder 9000 using the SFP ports, I have established a link and the interface is up.
The issue is that no data is passing through between the two, everything looks like it's up and enabled, spanning tree has detected the uplink port and has automatically set it to forward, both devices suggest the link is in place and the lights are on .
We recently purchased two 3750-X 48-port switches. We are in the process of connecting the Data Stack and StackPower cables. The question we have is what is the recommended Data Stack and Power Stack cable configuration if you only have two switches? All of the documentation that we have seen is for three or more switches.
Data Stack: Our assumption is that we will go from Stack 1 on the top switch to Stack 2 on the bottom switch. Do we need to then connect another cable from Stack 2 on the top switch to Stack 1 on the bottom switch? We would think not, but figure we should check. We plan on adding another three in the next budget year, which starts in May.
StackPower: Our assumption is that we will go from S-PWR on the top switch to S-PWR XPS on the bottom switch. Do we need to then connect another cable from S-PWR XPS on the top switch to S-PWR on the bottom switch? We would think not, but figure we should check.
- Catalyst 3750 Interface VLAN182 IP Address 10.62.182.254 255.255.255.0 Interface G0/2 Description Finger Print Server Switchport mode access
[code]....
Here are the problem,If i connect Finger Print Device to port catalyst 2960, some device not sending data to server, but if i connect all Finger Print to HUB and from HUB connect to Catalyst 2960 at port F0/5, All Device(Finger Print) can send data to server...Is there any special configuration in catalyst so all device can direct connect to port catalyst 2960 without HUB?
3750 Stack (Voice gateway for phones configured on the 3750 and has a VPC nexus) + + + + + + (Nexus5596) ++++++++++ (Nexus5596) (Gateway for all other vlan like PC / servers / etc) + + + + + + 3750x access layer (VPC to Nexus) [CODE].....
We are trying to configure RSPAN at one of our sites in order to record voice calls using CallRex. We have it working successfully at another site using RSPAN (smaller site with 4x 3560 PoE switches), but when trying to set it up at this site, it causes "instability" for the voice network to say the least (some phones display one-way audio, UCM down message on the phone...not good). The calls are actually recording successfully on the CallRex server, but we cannot leave the RSPAN config in place due to the issues it causes. As soon as the RSPAN commands are removed, everything behaves normally. Here is the relevent config:
The config is pretty stright-forward, but as mentioned above, is causing major problems when turned up.CPU / memory levels are normal. Nothing shows up in the sh log on either the Edge or Core switches.
I have a question about RSPAN, is this feature only supported on 6500 and 4500 switchs?
we have 2 3560 switches and want to use RSPAN to monitor different source ports.I checked thorugh the cisco feature navigator and the IOS we have on 3560 has the RSPAN fature listed in them.
We have Nexus 7009 switch and want to configure the span session
We are using F2 and M2 card both are in seperate differeent VDC.And out server is connected to M2 card on eth 4/6 and want to monitor the traffic from vlan 161Which is made on F2 card.
we want to record voip telephone?Presently im using wireshark on a laptop to test the rspan session
Here is how it's configured
CORE_SWITCH is Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 28 WS-C3750G-24TS 12.2(52)SE C3750-IPBASEK9-M 2 52 WS-C3750G-48TS 12.2(52)SE C3750-IPBASEK9-M
[code]....
Ive created the vlan 33 on my core switch and remote SPAN VLANs 133 Core switch is vtp server so i double checked on all switch and vlan 33 and 133 are present When i listen to conversation with wireshark we are only recoding voice of the one who is answering and we don't hear the other person talking?
I have configured Span port on our 4510. We have an application 5view server to monitor trafic connected to G9/17 Since we have changed the network connection from physical Giga port and add a Port-channel instead, we don't see any more trafic from the new Port-channel to G9/17
At present we are having a 4900 series switch where we are running one monitor session.Additionaly we are in need of capturing VLAN traffic and set the destination to 2 * GE ports , both are in the same switch.Due to the limitation of two monitor sessions per switch , we thought of putting the destination ports as port channel but it looks like it is not supported.
Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
I have a server windows 2008 that I would like to have a nic teaming configuration, the server has two nics, each nic is connected to a different switch. One is connected to cisco 2960 and the other is connected to cisco 2950. I have read here in forums about nic teaming but using the same switch. I have not found using different switch. Is this possible?
I have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506. The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.Now i have the necessity to connect the 2950 to the other catalyst, 4506B. So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
I have a cisco catalyst 2950 switch (flash:c2950-i6q4l2-mz.121-22.EA1b.bin), in remote location with public IP,how to upgrade ios remotely, by that time running configuration will go?how much down time is required and ?
I have 10 2950 switches on my network that support only 64 vlans on each one. I actualy have requrement to cleate around 100 vlans acros them, can I switch off vtp and create required vlans manualy? I will have more or less following set up:
c2950-i6q4l2-mz.121-22.EA10a.bin is the image name of the 2950 switch i have in my office. what is the meaning of " i6q4l2 "? I saw some IOS like IP base, adv-security. but i didn't see anything like this before.
What are the security issues in connecting a notebook to a console of the 2950 switch? Can virus or Trojan enter into a switch during configuration session? If the answer is yes, what precautions must I take to prevent such case?
i am having 2950 switch. Now i login through telnet but as per the company standard i have to login through ssh. Is there any possible to enable the SSH in 2950. Any IOS supporting this operation.
I have Cisco 7609 router and we have observed that router is rebooted due to the following error ;SLOT 3: Apr 13 16:06:26.621: %CARDMGR-2-ESF_DEV_ERROR: An error has occurred on Egress ESF Engine: Control Store Parity Error SLOT 3: Apr 13,Slot -3 we have SIP-400 card. We would like to know if there is any MIB which can monitir such reboots.
I am trying to test the gigabit ports on a Cisco 2950 switch. 1000Base-SX. I have the internet or dhcp server connected to port 24 on the first switch and my pc hooked up to the (any) port on the second switch. Both switchs are connected with a fiberoptic cable with MTRJ connectors on either side.
Now when I use gi0/2 on both switchs all works fine. I get a dhcp address from the router on the other end of the first switch. but when ever I include gi0/1 on either end of the fiber optic cable neither of the ports will initialize (neither of the leds above the ports light up). I have deleted all the config files before booting up the switchs so they should have a default blank configuration.
When looking at the Http web page for the switch I dont see any issues with the port. what can I do to make sure these ports are working or can be configured?
I will not be able to post back any more information about the switch until next tuesday. Im off till then.
Stumped again with my Catalyst 2950. Everything is working perfectly with wan/dhcp/router on fa 0/1 with all ports assigned to vlan1. All devices plugged in connect to the router correctly with ip's being assigned via dhcp.Instead of hooking up by console port I want to be able to SSH or telnet in to the switch using any port while still maintaining the above functionallity. Is it possible to assign a dhcp assigned ip address to vlan 2 and have vlan1 and 2 bridged? Or is there a better way of doing this ?
spam up the boards with the same basic CCNA level stuff, but I have a couple of questions about ios differences, limitations, and references. I have the following three switches. One appears to be considerably dated in regard to software version. My confusion/ignorance stems from managing VTP settings.
When I set either 2950 switch as the VTP server, and the other as a client, the client inherits the server settings as expected. However the 2924 requires that I go into the vlan database from priv exec and manually set vtp client. That's pretty similar to setting any switch to client mode. The problem I am observing is that after setting the 2924 to client, it still doesn't inherit vtp version settings or pruning settings. I still have to manually configure those. Additionally, if I copy run start the 2924 after making these manual settings, and then reload the switch, all the settings are lost and it defaults back to server mode with all features disabled. From my searches, it looks like vlan information is stored in vlan.dat, but all the documentation I've found is on 12.1 ios which doesn't appear to use vlan database for vtp setup, meaning it might still be an issue, but not one I'm focused on at the moment.
Is the vlan database dumped at reload? I've read vlan.dat is stored in nvram and should be saved after a copy run start, but that is not the case for me.I have since set the 2924 as the server, manually configured the server from vlan database, executed copy run start, and reloaded the switch. Oddly, my manual settings saved from the reload, meaning I only lose settings when the switch is in client mode.Am I missing additional necessary client commands to save the config, or is this just a limitation of either the 2924XL or the 12.0 ios?On a related but completed out of scope topic, without a cisco service contract, how am I supposed to make heads or tails of all the different versions of ios, along with the letter-based features and what-not? I can't even find my 2924 in the list of platforms when searching for ios upgrades.
