I'm installing a new 6506E switch and I want to use dual supervisor redundancy. I also have a spare sup 32 from another switch which i'm not using right now.I want to save some money. My question is Can I use one sup 720 as primary and the 2nd redundant sup 32 as a secondary on the same 6506E switch?
View 2 RepliesI have problem with my Cisco 6506E switch.when it reloads its going to RMON mode, If I give Boot command I. The RMON, then only it will get load with the iOS image.
View 2 Replies View RelatedDoes the port adaptor PA-MC-2E1/120 work with the Catalyst Switch 6506E (Sup Engine: 720-3B)? We have bought a Enhanced FlexWAN card for this port adaptor.I read through the cisco website and seem to get confusing answers whether they are compatible.
View 1 Replies View RelatedI see the command "vlan access-log ratelimit 2000" and wonder what it is that it does.
View 2 Replies View RelatedI am looking the power requirement for 6506E in data sheet and it shows that is support 3000, 4000, 6000 & 8700W. I have currentely 4000W power source for my new 6506E switch. will it work with below modules in new 6506e ?
View 2 Replies View RelatedI am upgrading a Cisco 6506E VSS from 12.2(33)SXI5 to 12.2(33)SXJ5 during a maintenance window. So I have plenty of time to reboot the VSS. Confirm below is the correct procedure. I have manually copied the new IOS to both active and standby Sup720s.
no boot system
boot system flash sup-bootdisk:NEW_IOS.bin
boot system flash sup-bootdisk:OLD_IOS.bin
!
copy run start
reload
I was going through the below cisco document and there are a few more steps as below: Is it necessary?
[URL]
Router(config)# no boot system
switch 6506 E with supp 720 does it support 10 GIG module ?
View 3 Replies View RelatedI'm trying to boot this IOS on a 6506-E, s72033-adventerprisek9_wan-mz.122-33.SXI8.bin.
This is what I see in bootvar.
sh bootvar
BOOT variable = disk0:s72033-adventerprisek9_wan-mz.122-33.SXI8.bin,1;disk0:s72033-ipservicesk9-mz.122-18.SXF8.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102
Standby not ready to show bootvar, I want to remove SXF8 and leave SXI8 alone. I removed both IOS file names in boot system and added the SXI8 again and saved. So this would be the output after.
But after a switch restart, this would be the output of show bootvar again.
sh bootvar
BOOT variable = disk0:s72033-adventerprisek9_wan-mz.122-33.SXI8.bin,1;disk0:s72033-ipservicesk9-mz.122-18.SXF8.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102
Is there anything I need to check? This is an old engine and I'm not sure if the variables of the RP modified .
I have a catalyst 6506E (WS-C6506-E) with a SUP2T supervisor (VS-S2T-10G) card and a 10G interface card (WS-X6816-10G-2T) + DFC4.I have configured an etherchannel to another switch with the 2 10Giga ports of the SUP2T card and 2 10giga ports of the interface card.I only use the 10Giga ports of the SUP2T card so the cards have the same QOS transmit capabilities.But they do not have the same receive capabilities.
So when I configure QOS (with the new commands on SUP2T) on my 4 ports within the Etherchannel, 2 ports move down because of the inconsistency.
Till this point, no surprise.
The problem is that the command "no platform qos channel consistency" replacing the "no mls qos channel-consistency" does not exist.I run the last IOS 12.2(50)SY1 IPSERVICESK9.
And I cannot have QOS on my Etherchannel on the 2 cards.Or I have to use 4 ports of my interface card but in case of failure of this card, I loose the whole etherchannel.I there a way to avoid the consistency check ?
I describe an issue when i need to performe an L2 or L3 Etherchannel from a Catalyst 4948 IOS Enterprise and 2 xCatalyst 6506E bandled with VSS.
From the VSS Side when i plug cables i see on the physicals and Etherchannel that Physical and protocole layer are up. On the 4948 side, I see that physical layer is up and protocol and Etherchannel interfaces are down.
On the Etherchannel port summary i see that the port state is supended.
On the first attempt, i have test with a L3 etherchannel on both side using no switchport with two IP addresses one at each side on etherchannel interfaces.
The etherchannel are bundled with LACP mode active and on the second attempt with PAGP mode ON.
The same configured on VSS 6506E work fine with Catalyst 3560E.
We have 20+ VLANs on our main network, we have an offsite connected by metro GIG fiber ethernet. Right now, we have a layer 2 connection to there with the core at the main site as the gateway. We have had problems occationaly with the metro ethernet's spanning tree which then we would see our own network and cause an outage, not only for the offsite, but since the VLAN would see itself (not on our equipment but the metro ethernet carrier's) it would effect the main network as well.
What I was going to do to resolve this was change the connection to a routed network, however I need to still send some VLANs over the routed network (there are some applications that require to be on the same subnet as the server). Is there a way to Map the Vlan 10, and 11 at the main site to a vlan 10, and 11 at the remote site using a routed network? I noticed there is something about bridging, would I bridge the VLAN accross the routed MAN connection? Then would I bridge back the other way as well?
Main site has a 6506E
and offsite has a 3750E
I need 10gigbit uplink for this switch. What are the other devices that i need order along with this device.And what is the diff between X2-10GB-LR= and CVR-X2-SFP.if i take CVR-X2-SFP, in future how can i upgrade from one gig to 10 gig?for current use i need 10gig support required. so what are all the other devices that i need to order.Fiber multimode and distance 15Mt only.
View 2 Replies View Relatedi have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View Relatedwhat is the use of no switch port command in L3 switch?
View 7 Replies View RelatedI have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies View RelatedI have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View RelatedThe last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
I recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router.
Switch Config
interface gi2
description connection-to-data-vlan
exit
interface gi3
description connection-to-internet-vlan
exit
vlan database (code )
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedI am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
I'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
Two Cisco C2960G Switches connected with each other using an EtherChannel Trunk Ports.IOS Image has been upgraded to c2960-lanbasek9-mz. 122- 58.SE2.bin.The global command "sdm prefer lanbase-routing" has been executed to set the default template to "lanbase-routing".The global command "ip routing" has been executed to enable the ip routing.An IP route has been configured in each switch to point to each other for the static routing purpose (Please see the 2 attached configuration files) The hosts in VLAN 111 and VLAN 110 are not able to see each other even the ip static routes have been configured.May be I have misconfigured some settings but not sure what's the actual problem.
View 11 Replies View Relatedmy company pay a switch 3750 X. WS-C3750X-24T-E. It uses IP services basically but I failed to configure InterVLAN routing. why interVLAN routing doesn't work on my switch?
View 10 Replies View RelatedYou can set the ME3400 switch set to the Routing SDM template such that it support PBR. That is done in the ASICs, right? Because if it is done in software the switch could quickly become overwhelmed.
View 2 Replies View RelatedI have a 3550 l3 switch configured as follows:
vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21
I have the servers, switch and router connected to vlan 21. Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
[code]
Building configuration...
Current configuration : 4833 bytes
!
version 12.2
no service pad
[code]....
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies View RelatedI'm having some problems setting up vlans to talk to each other on a 3550-12T switch. Its quite a simple setup I have, but I need to split my network up.
Currently I have a network of 192.168.25.0 255.255.255.0 I want to create a new vlan network of 192.168.30.0 255.255.255.0 So I have configured my vlan1 (default vlan) to have an ip of 192.168.25.250 for getting to the management page
I have created a vlan2 of 192.168.30.1 255.255.255.0 ?I have a port 10 linked to one of my 3560G's?In port 9 which is on vlan2 I have my pc plugged in with a static ip of 192.168.30.50 from the router I can ping any device on 192.168.25.x.
I can not ping 192.168.30.1 (which is my vlan2) nor can i ping the PC.
I have enabled ip routing But I dont have a default route, this is becase we don't have a router on the network.
I am looking for a PoE switch with Routing capabilities (e.g osfp) something lower end than 3560E.
View 10 Replies View RelatedI have Layer_3 " 3750-x " , so I can't do any routing on the switch , so if I need to Upgrade the IOS what is the proffered image that support hte routing , and Is it free or should I pay?
View 7 Replies View Related