Cisco Switching/Routing :: Untagged VLAN On Subinterface 2821
Sep 8, 2012I need to configure a subinterface eg g0/0.1 and g0/0.2 with a untagged VLAN for each subinterface on a Cisco 2821.
View 5 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 2960 Set Ports To Untagged VLAN XX
Aug 6, 2012I have two questions for a Cisco 2960 (WS-C2960-24TC-L)
1. I am working to setup a few Cisco 2960 switches for HP iLO access to our servers. We are going to segregate the iLO network (VLAN 40) from the data network (VLAN 10) by using a different VLAN. All of the HP servers will be configured with static addresses. My question is, how do I set all the ports to VLAN 40 so that untagged devices will automatically go onto VLAN 40? I don't want to have to configure the VLAN on each iLO port on the server. I tried to set the port to: "switchport trunk native vlan 40", but that didn't work.
2. Also, how do you access the web GUI for these switches? I get a login box, but putting in the enable password doesn't work. I have the following commands in the config: [code]
Cisco Switching/Routing :: 2821 Inter-Vlan Routing And IP NAT To ISP?
Jun 25, 2012I have just bought myself a Cisco 2821 ISR.At present in my home I have a Cisco 2621XM. Fast Ethernet 0/0 is connected to a 3524XL as a trunk to provide my LAN with inter-vlan routing. it works great. Fast Ethernet 0/1 is connected to my ISP's cable modem and uses the command "Ip address dhcp" to get an IP and all other info from my ISP.FA 0/1 is Ip nat outside and the FA 0/0 and all sub interface like 0/0.1 .24 .168 etc all ip nat inside.I get intervlan routing and access to the internet via this router.I have this 2821 to replace the 2621XM as I plan to run CME on it and want gigabit routing on my vlans as at the moment on the 2621 routing between vlans it at half duplex or seems to be.I have configured the 2821 to ip nat outside on gig 0/0 and ip nat inside on gig 0/1 and all of the sub interfaces (same setup as my 2621 but with gig ethernet)I have no access to the internet at all but I can ping www.google.co.uk and other domain names from the terminal session when I am connected to the 2821 via the console or telnet/SSH. the gig 0/0 has an IP assigned from my ISP too but no other nodes on the network can ping outside.Am I missing something here? the version of IOS is V 15.
My access list goes someting like
access-list 1 permit 10.0.0.0 0.255.255.255
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 100 permit ip 10.0.0.0 0.255.255.255 any
access-list 100 permit ip 192.168.1.0 0.0.0.255 any
and so on
I still cannot access the internet.....
Cisco Switching/Routing :: Extending VLAN Default Gateway With 2821
Jul 25, 2012I have a design hurdle that I cannot seem to cross. I have two sites and I need the same VLAN to span both sites. I have accomplished this using L2TP but my issue is that I can no longer assign a gateway for this VLAN on the router. The 2 routers are 2821's and are connected with a dedicated fiber run.
Ant recommendation for how this could be accomplished? It would be great if I could have the same gateway at both sites by leveraging some sort of bridged interface (BVI so I've heard) but I am at a loss as to where I should start with this. Also, this is not the only VLAN that needs to traverse the link.
Cisco Switching/Routing :: 2821 Best Way To Block A Vlan From Accessing Other Vlans
May 22, 2012I have a LAN with 6 vlans and a 2821 router. By default, intervlan routing is enabled for all vlans, however, I want specific vlans to be denied access to others, though all should still be able to use the Internet being served from GE/0.
View 6 Replies View RelatedCisco Switching/Routing :: Multicast On Subinterface On 861?
Feb 7, 2013I have an 861 that we are using for a test network and need to add static igmp addresses for multicast. We are using the router as a router on a stick with subinterfaces on the WAN link. I've looked everywhere to see how to add the static igmp addresses.
interface FastEthernet4
no ip address
no ip route-cache cef
[Code]....
Cisco Switching/Routing :: 3560 / Creating Extended VLans And Subinterface?
Jan 24, 2013We have a 3560 switch running IOS universalk9-mz.150-1.SE3.bin.Recently, we saw two problems with this switch:-
1. if we try to enable subinterface on any routed interface , for eg. gig1/1, it says invalid input detected. It doesnt accept encapsulation command also. Following was done to enable subinterface:
int gig1/1
no ip address
int gig1/1.2000
ip address 1.1.1.1
under the gi1/1.2000 subinterface, it doesnt present the option of ip address.
2. we created a layer 2 vlan 2000 like: vlan 2000 When we do an exit after creating this vlan , it gives following error:-
%SW_VLAN-4-VLAN_CREATE_FAIL: Failed to create VLANs 2000: extended VLAN(s) not allowed in current VTP mode
Cisco Security :: Subinterface Stops When Use VLan 1 Default ASA 5520
Mar 17, 2011I´m trying to configure a subinterface named Inside with vlan 1 but the interface stops work with this vlan.My switch is a Cisco and use the lan with vlan 1 too.If I change de vlan for other i.e vlan13 works fine. And all others vlans works fine too.Is there a problem to use the vlan 1?
My configuration is:
Cisco ASA:
interface gig0/3
no ip address
no security
no nameif
Interface gig0/3.1
vlan 1
nameif Inside
Securirity-level 100
ip address 10.x.y.x 255.255.224.0
The giga port of the swtich is configure to trunk model.
Cisco Switching/Routing :: TR50 - Priority Queuing Of Packets On Frame Relay Subinterface
Nov 13, 2011I need to get some low volume, interactive data, prioritized on frame relay PVCs across our network. I have followed the CBWFQ examples from cisco.com, but my test packets are still showing latency over 1 second. My lab set up has a corporate connected gateway router linked via FE to testrouter 50. TR51 has a T1 frame relay loop to another router acting as a frame relay switch. The other side of the FR switch has a 56k link to testrouter51. I am sourcing test pings from my desktop PC, that are marked as AF43, and leave at a rate of 1/second, when the response comes back in time. I am using a Smartbits to generate some default class traffic at a rate of about 56Kbps only in the 'outbound' direction, toward TR51, as this emulates a file copy from corporate to remote sites, that is causing the AF43 traffic to suffer. Here is the relevant config on the TR50 device:
class-map match-all rtu-data
match ip dscp af43
!
policy-map frame-56
class rtu-data
priority percent 20
class network-mgt-data
bandwidth percent 5(code)
Protocols / Routing :: Machine Refusing Untagged Ports
Mar 14, 2013Our College uses Ethernet connexion for its students with the IPv4 Address of each machine configured using DHCP (not manually). In order to prevent students from playing certain online videogames some ports are blocked for all machines on the network, but they can be manually untagged (ie for competitive play). The problem occurred when we tried to untag the ports to allow online games on this machine. After the allowed ports were modified, the machine refused to assign an IP adress to itself - no matter how many times we try to renew the DHCP Lease. Restoring the previous set of allowed ports fixes the problem, but doesn't allow for online play.
config: OS X 10.8.2 with nothing fancy. Other machines on the network do no experience this problem.
Cisco Switching/Routing :: 2821 Periodically Stops Routing All Traffic
Oct 3, 2010We've got a cisco 2821 router which periodically stops routing all traffic. It seems to happen about once every 2 weeks, and I can't find anything that could be causing it. There are no entries in the log and the router stays up and running but requires a restart to begin processing traffic again. We're running 12.4(13r)T11.Any thoughts, or troubleshooting steps to track this down?
View 7 Replies View RelatedCisco Switching/Routing :: 2821 Multicast Routing Relay Basic
Mar 12, 2013I start configuring Cisco 2821 router for multicast . First short description and attached sheme explanation. Let we say I have small network with 100 users. One router and Cisco switch 3560. Two VLAN’s, one for data another for multicast. Data from internet works fine but now I want to connect multicast servers (or source of more multicast streams) from another subnet. Router have three interfaces.I expect there should be no problems with multicast configuration, but unfortunately it is not like I expect. What I did ?
First step: enable multicast routing
Second step: on both interfaces (Fe 0/1 and Fe 0/2) - ip pim sparse-mode
Third step: configure switch that users are connected to access port in VLAN 222 (temporary to see if multicast work)
When I start VLC on computer nothing happend. If I try to connect computer on same subnet where is source of multicast streams it works fine.What I am doing wrong ? Is there anything about routing ? All subnets are directly connected. RP is not needed if I have one router or ?
Cisco Switching/Routing :: 2821 - Routing With Public LAN IP
Jun 7, 2012I have a Cisco 2821 Router. Its ethernet Interface(E1) is connected to an ISP's Gateway.The outside interface IP is 207.x.x.1, The ISP has given 6 public IPs (202.x.x.1- 202.x.x.6) to use in LAN.
I have configured the router`s Internal Interface(E0) with a public IP address. (i.e. 202.x.x.1)
My Internal LAN PCs are in a private range of 192.168.1.0/24 subnet. Now I wanted my PC users to access the Internet while the Routers public IP remains on internal interface. How can I do the same?
Cisco Switching/Routing :: 2FE-2W Compatible With 2821?
Dec 6, 2011I have a 2Fe-2W Card and wanted to find out if it can be picked up and installed on a Cisco 2821? Below is the version
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(8a), RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2006 by Cisco Systems, Inc.
ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)
System image file is "flash:c2800nm-adventerprisek9-mz.124-8a.bin"
Cisco Switching/Routing :: 2821 With 16-ESW CEF Low Memory
May 29, 2012According to my boss every 3 to 4 months he has to restart our 2821 with a 16-esw module installed because of a low memory issue dealing with CEF. Here is the exact error message.
%% Low on memory; try again laterJun 8 11:18:51.777: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:19:51.823: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" %%
Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
Jun 8 11:20:51.868: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:21:51.914: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed
Cisco Switching/Routing :: Interconnect Between 2821 And HP 5412zl?
Jan 27, 2012I have a 5412zl 10.215.x.x/16 Most of the connections on this switch are on vlan1. B9 is the port which is connected to a Cisco 2821 Router. The port on that end is GE0/1. The port on the cisco side is not a trunk but configure with an ip of 10.215.1.30/24 Its part of a some ip access group. The network that i now sit on is a 172.x.x.x/24 (behind cisco router, about 3 hops to that main 2821)We current have a system on my side that talks to a server on the 10.215. that has no issues. I'm trying to access some switches on the 10.215. and have had no luck reaching them.
Here is the access list that i found that port is configured to use:
permit ip 10.215.0.0 0.0.255.255 172.18.0.0 0.0.255.255 permit ip 10.254.0.0 0.0.255.255 172.18.0.0 0.0.255.255 permit ip 10.215.0.0 0.0.255.255 172.14.0.0 0.0.255.255 permit ip 10.254.0.0 0.0.255.255 172.14.0.0 0.0.255.255 permit ip 10.215.0.0 0.0.255.255 192.168.2.0 0.0.0.255 permit ip 10.254.0.0 0.0.255.255 192.168.2.0 0.0.0.255 permit ip 10.215.0.0 0.0.255.255 192.168.20.0 0.0.0.255 permit ip 10.254.0.0 0.0.255.255 192.168.20.0 0.0.0.255 I would think the first permit would allow me to get through to the 10.215 side but maybe i need to set something up on the hp size to let it know how to get back? I'm very new to this stuff.
Cisco Switching/Routing :: 2821 Forwarding Udp Broadcast
Jul 31, 2012I have 2821 router configured with two subinterfaces. This router is connected on cisco 2960 switch. The trunk on 2960 is configured without any prunning of vlans. I noticed that udp broadcast traffic is being forwarded through my router on native vlan 1 (this interaface do not have ip address configured). Below is configuration:
Router:
interface GigabitEthernet0/0
no ip address
duplex auto
[Code]....
Cisco Switching/Routing :: Failover VPN With 2821 And ASA 5510
Jul 2, 2012Currently I have a network that looks like this:
ASA5510 - - - Internet - - - ASA5510
| |
EIGRP EIGRP
| |
2821 -----------MPLS----------1841
BGP
The MPLS connection is currently down, I'm trying to run a failover Site-to-Site VPN over the internet. All of the examples I've read have both connections involved in the failover coming out of one device. Since I'm not working that way, what is going to be the best way to failover? Do I need to set up some sort of IP SLA in the config? Or can I somehow weight routes in EIGRP in a way that the connection will failover from Internet to MPLS when the MPLS goes down and vice versa when the MPLS connection comes back up?
Cisco Switching/Routing :: What Is The Maximum Nr Of VPN Clients On 2821
Mar 10, 2013What is the maximum VPN Clients that could be connected to cisco router 2821, with this IOS c2800nm-adventerprisek9-mz.124-20.T.bin
View 3 Replies View RelatedCisco Switching/Routing :: 3560 Possible To Create Vlan Inside Transport Vlan?
Jan 10, 2012Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedCisco Switching/Routing :: 3750 - Extending VLAN To Remote Switch That Already Has VLAN ID In Use
Jan 10, 2013I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
Cisco Switching/Routing :: Route Data From Vlan 10 To Vlan 20 On 2960s?
Mar 31, 2013i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
Cisco Switching/Routing :: 3750G / VLAN 1 Is The Only VLAN And Its Disabled
Sep 16, 2012I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies View RelatedCisco Switching/Routing :: L2tpv3 Vlan-to-vlan Tunnel On 890
Jun 13, 2011I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
Cisco Switching/Routing :: Low Bandwidth On 3750 From Vlan To Vlan?
Nov 20, 2012We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
Cisco Switching/Routing :: 2821 Bogus Arp Table Contents
Jul 23, 2012My 2821 router has an arp table with the wrong ip to Mac mappings. The impact is that I can reach any host in the 10.1.1.1 subnet. I can reach hosts in the 192.168.35.0 just fine. [code] It is as if the 192.168.35.1 device is answering all arp requests as a proxy arp or something. Clear arp-cache nor clear ip arp on my 2821 have any affect.
View 1 Replies View RelatedCisco Switching/Routing :: 2821 Router Hangs And Reboot
Nov 13, 2012Yesterday my router was hangs and my services was stuck. I start the router hard booted and it works fine.This was second time i was facing this kind of scenario. The attached are the "show tech support" of the cisco router 2821.
View 2 Replies View RelatedCisco Switching/Routing :: 2821 Software Forced Crash
May 14, 2012I have a cisco 2821 router in rommon and displaying the message '' softwre forced crash '' and '' checksum error'' .I tried to do rommon tftpdnld but as the image is self decompressing into the ram it again crashes with the same error although i have done it with various valid ios but in vain.
View 1 Replies View RelatedCisco Switching/Routing :: Possible Load Balancing On 2821 Router?
Apr 15, 2012I have a 2821 Router, with a VWIC2-2MFT card in it, with two T1s going into that card. The two T1s are a bundled MPLS line.
I then have a cable modem connection going into the gigabit Ethernet GE 0/1 port on the router.
Right now, the cable modem provides a backup connection in case the T1s go down.
What I was wondering is if there was a way to 'combine' the bandwidth from the two T1s with the cable modem?
Cisco Switching/Routing :: Upgrading Fans On 2821 Router
Apr 3, 2012Basically I run 3 voice gateways on 2821 routers. In two of my routers I've had fan failures, one router has had two fans die and one has had just the one.
I was going to buy the offical Cisco fan replacement kit but then I thought with such as high failure rate I'd rather buy something else and better guarentee the service to my call centres.
So, what i'm asking is:
- Is there any reason why I cannot procure a standard 80mm 12V fan with a better rating (cooling and reliability) and install this in my 2821's?
I understand this may invalidate any warranties but mine have long expired.
Cisco Switching/Routing :: How To Configure Dual ISP On Router 2821
Mar 17, 2013I've 3 interfaces on router:
Gb0/0-ISP01 with DHCP client
Gb0/1-ISP02 Static IP 192.168.2.x/24
Fa0/0 - LAN 192.168.1.1/24
I want to know, how to configure:1. Set the IP of interface Gb0/0 as dhcp client from ISP01 and make it as default route.
2. How to configure the ip nat.....overload?
3. How to use the ip sla to monitor internet connectivity to 8.8.8.8 for ISP01, if it fails, to go to ISP02.
Cisco Switching/Routing :: 2821 - Router High CPU Utilization?
Sep 25, 2012We've got Cisco 2821 for our 90mb/s Internet Access. Its CPU usage is around 80%. Show process cpu does not show any cpu proccess with high utilization. But we have got plenty of policing configured for our clients using policy maps. Can this policing affect cpu usage?
View 1 Replies View RelatedCisco Switching/Routing :: 2821 High Interface Discards
Apr 8, 2013I am having an issue pinpointing why my 2821 router is discarding so many packets when transferring data to our second site. The traffic flows from the local lan, to the router, where it is redirected via WCCP to a WAN optimization device, back to the router and over a GRE tunnel to the second site where the same process happens. The traffic does get there, but the LAN/Repeater router interfaces have around 20,000-60,000 input drops an hour. From the output below, it looks like traffic is being dropped by the RP.
I just restarted the router as a last resort, and here is what has accumulated in the last 30 min:
FastEthernet0/0/1 is up, line protocol is up
Hardware is Fast Ethernet, address is 0025.840c.7680 (bia 0025.840c.7680)
[code]....
And CPU never goes above 40%
100
90
80
70
[code]...