Cisco VPN :: 3000 - How To Generate PCF File For Remote SW Client
Oct 10, 2011I can't seem to find out how I can generate a PCF file for a new remote vpn SW client? I have a VPN Concentrator 3000 series.
View 1 Replies
ADVERTISEMENT
Cisco Firewall :: How To Generate A CSR File To Renew Out SSL Certificate On ASA 5510
Jun 13, 2013How to Generate a CSR File to Renew out SSL Certificate on ASA5510 v9.0(2) - ASDM v 7.1(2) ?
View 1 Replies View RelatedCisco Switching/Routing :: IE-3000-8TC / CLI Vlan Command Does Not Work Inside A Config File
Apr 21, 2013my environment:
IE-3000-8TC industry-switch
ios: ies-ipservicesk9-mz.150-2.SE2
if i do
vlan 12
name NextVLAN
state active
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.
Cisco VPN :: VPN Concentrator 3000 Setup With Client
Mar 27, 2011I've the following scenario VPN Concentrator is connected to a router which is connected to a router and at the edge Cisco 515E PIX is connected to the internet. The problem is that the normal VPN Dial-up connection (a utility of windows) are getting connected but Cisco VPN Client throws error 412. Here's what I've tried (Initially groups and user were created):
(1) Allowed port 10000 on PIX ( access-list from-outside-coming-in permit tcp any host <public ip> eq 10000) and checked IPSec over UDP on VPN Conc. under Mode Config tab. Also checked IPSec over TCP tab under tunneling panel at port 10000. Tried connecting through VPN Client but it threw error 412
(2) In the reference guide, I read that IPSec over NAT is allowed on ports ranging from 4000 something to 40000 something.
I tried 33333, both on PIX and VPN Conc. under Mode Config tab but still no use. Same error 412.
Cisco VPN :: VPN 3000 Client Users Change Password
Apr 1, 2013For access by external users on our network use all Cisco VPN Client, we have a VPN3000 Concentrator and a Cisco ACS 2.6 for authentication.We wanted to upgrade to the latest release of ACS 4, x .... you can set a password expiration for VPN Client? Or make sure that the remote user can change password?
View 2 Replies View RelatedCisco VPN :: 3000 / Detect Connection Status For AnyConnect VPN Client?
Aug 9, 2011I need to write a small piece of code in C++ to detect whether the AnyConnect VPN client (v2.5 and above) has established the connection. I recall in Cisco 3000 VPN client when the connection gets established there is a registry value (TunnelEstablished) being set to 1. But with AnyConnect I don't see any changes in the registry. how to detect this in C++?
View 4 Replies View RelatedCisco VPN :: Installing VPN AnyConnect Client On Lenovo 3000 Laptop?
Sep 13, 2012I uninstalled all of the Lenovo built-in remote assistance software, but still am getting an error on initiating the VPN.When I try to run the client, I'm asked to select the Group, enter the Username and Password, which I do.
I get a message saying "Establishing VPN - Repairing VPN adapter", then it crashes and reports: "AnyConnect was not able to establish a connection to the specified secure gateway. Please try connecting again."
Copy File Of Remote Computer To Another Through CMD?
Feb 12, 2012How do i copy file of a remote computer to another remote computer through cmd
View 1 Replies View RelatedBatch File For Remote Computer?
Sep 26, 2011 i'm trying to write a simple batch file to make my life easier. We have a few dozen Aix Boses that we telnet into and about 70 as400 Swift systems we telnet into. i was starting on a batch file like the one below where i could run it, type in the system and it log me over.What I want to add is for it to put in my user name. (if i could draw a password from a excel file that would be fantastic but id settle for just my user name). I have tried - l (username) at the end of telent and it didn't work. also tried -a. i keep getting the box with user name/password and there both blank. how i can get it to type in my user name?
here is my script.
@echo off
set /p name= What system are you logging into?
telnet %name%
i tried start script.vbs as another attempt using this info
Set cloner = CreateObject("WScript.Shell")
cloner.run"cmd"
WScript.Sleep 500
cloner.SendKeys"telnet %name%"
cloner.SendKeys("{Enter}")
WScript.Sleep 500
[code]....
Setting Up Remote Access File Server?
Jun 22, 2012I have to share some PDF files with members of my organization, I have a Windows XP Pro box dedicated for this. Currently they can access it from within the office as a shared folder. I would like to make it available remotely is there a better way other then as a FTP access.
View 1 Replies View RelatedSharing :: Attach File To Email Via Remote Upload?
Jan 11, 2012are there any free services where you can remote upload a file (zip file 25MB) and have it sent to me via email as an attachment. not a link where i have to download the file.
View 1 Replies View RelatedCisco VPN :: PIX 6.3 Remote Client VPN / Traffic One Way Only
Sep 20, 2012I have a few ASAs with L2Ls in a hub-and-spoke fashion, works great. All ASAs are 8.2(1). I've tried to add remote-vpn to the HQ ASA. I have this working on a PIX 6.3 box at HQ, but have not been able to make it work completely on the ASA.
Just to check, I also set up remote client vpn access on one of the spoke ASAs, and that actually did go well. Applying the equivalent config on the HQ ASA - won't function.
The problem with the HQ ASA remote client vpn is that after completed phase 1 & 2, the traffic goes one way only, from client side towards the ASA. I e remote side only encaps, no decaps; ASA side only decaps, no encaps. If the remote client pings a host on the inside (i e behind the HQ ASA) the packets arrive, and are returned towards the ASA (a correct route for the remote vpn network is in place on the inside host). However, it seems as if the ASA doesn't send that traffic back into the tunnel, but rather sends it unencrypted through the default route (doing a traceroute from the inside host for instance suggests this).
The ONLY way I can pass traffic towards the remote client is by initiating a ping from within the HQ ASA, it's the only time I get encaps on the ASA side and decaps on the remote side of the tunnel. Interestingly, it's actually the "ping outside 192.168..." that works, doing an "inside" ping fails. Compare this to the spoke ASA and its remote vpn client, there an inside ping is succesful, but not a outside ping, i e the spoke ASA functions as expected with its remote vpn. Given that the configs on the two ASAs are the same for remote client access, I would have expected both to work, not only one of them. But then, the HQ ASA has more lines of code, and I guess that something there gets in the way. [code]
Cisco :: Client Behind NAt Access Remote Desktop?
Jan 22, 2011I have A setup in different location with the the ASA Firewall with VPN enabled and a Print server. on Network B i have a server with 2008 installed and its my NAT server, DNS and File server.Now the Client on Netwrok B wants to access the Server in Network A Remotely through VPN they could connect to but cannot user Remote Desktop either its Ip translation issue or i dont know.
View 2 Replies View RelatedCisco VPN :: Client Behind EzVPN Remote (ASA 5505)?
Feb 2, 2012I try to configure a simple EzVPN infrastructure:
EzVPN Server (CISCO2811, hostname cme) < -- > EzVPN Remote (ASA5505, hostname ezvpn-asa) < -- > Client
Attached you find both configuration of the EzVPN server and remote. The tunnel is getting up and if I ping from the ASA to the Router, I see the packets getting encrypted:
ezvpn-asa# ping 172.16.100.1
...
ezvpn-asa# show crypto ipsec sa
interface: outside
Crypto map tag: _vpnc_cm, seq num: 10, local addr: 172.16.100.2
[code]....
If I connect a client with IP address 192.168.1.2 to the interface eth0/1 and do a ping to the cme, I don't see any packets getting encrypted. I don't have any idea about VPN, I just need it for a wireless lab environment. What do I have to configure on the ASA, so the inside traffic is encrypted?
Cisco VPN :: 2911 ISR Remote Client Connects Just Once?
Feb 2, 2011After trying to configure remote client VPN access to a Cisco 2911 ISR using the CLI I tried to use the Cisco Configuration Professional. However, either way I have the same problem. A client can successfully connect and access servers but just once. When the client disconnects and tries to connect again there is no access to the servers even though the VPN tunnel appears to be up. I've tried multiple versions of the Cisco vpn client SW and all behave the same: 1st connection can access servers, subsequent connections can't. I've also tried a second (different) client after the original connection and still no luck. If I reload the router the client can get the vpn connection and access the servers but if the client disconnects from the vpn and tries again there is no access to the servers.
I've also tried it with and without NAT but it doesn't seem to make any difference.
The config generated using CCP is as follows:
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
Cisco VPN :: ASA 5505 - VPN Client Will Not Access Remote Lan
Mar 10, 2013I have an ASA 5505 that is on the perimeter of a hub & spoke vpn network, when I connect to this device using the VPN client I can connect to any device across the VPN infrastructure with the exception of the sub net that the client is connected to, for instance:
VPN client internal network connects to 192.168.113.0 /24 and is issued that ip address 192.168.113.200, the VPN client can be pinged from another device in this network however the client cannot access anything on this sub net, all other sites can be accessed ie. main site 192.168.16.0/24, second site 192.168.110/24 and third site 192.168.112/24. The ACL Manager has a single entry of "Source 192.168.113.0/24 Destination 192.168.0.0/16 and the "Standard ACL 192.168.8.8./16 permit.
Cisco VPN :: 2811 / Remote VPN Client Is Not Communicating With LAN?
Apr 19, 2011I have a cisco 2811 with security bundle with IOS 12.4(13r)T I am planing to use this router as a VPN gateway for company ( i.e)
1. LAN 2 LAN VPN ( Supporting if remote site is having dynamic IP)
2. Remote access VPN for VPN client
I have configured the router ( attached is the configuration) I have not tried to use the LAN to LAN VPN ( first i complete remote access VPN and then check L2L) I tried to use the remote access VPN I am able to connect from vpn client software and got the IP address but unable to ping the servers in LAN.
2x Client On Android To Remote Into Desktop
May 25, 2012This is probably where I should have started my search. During the last 2 days I have taught myself numerous things to try and figure out this problem. I want to run 2x Client on my android to remote into my desktop. I have a Verizon fios actiontec router ver. I and running win 7 prof.. I have been able to easily set up the 2x client and remote into my desktop while on my home wifi but trying to use 3g/4g service has yielded nothing but heartache and stress.
View 4 Replies View RelatedTP-Link 150Mbps Wireless :: WR740N - Unable To Connect Remote Desktop And Do File / Printer Sharing
Feb 19, 2013Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : BSNL
I am facing some issue in LAN network.I have connected one desktop( win 7) and another desktop (win xp) to the TP link router. Both the computers got ip address and able to share the internet. But both the computers are not in the same network. That is they cant PING each other. hence they are not visible to each other.
Cisco :: Does IOS Tftp Client Support Remote Symlinks
Mar 27, 2012Question is in the subject line. Maybe I am missing something, but this does not seem to work (No such file or directory).
View 3 Replies View RelatedCisco :: Remote Vpn Client To Router With Cellular Interface?
Apr 28, 2011I'm having extreme issues in getting my vpn client to connect to a cisco router with a hwic-3g-hspa cellular interface
I have tested the config remotely by traversing the tunnel I have setup with a cisco vpn client and the client does connect, however when out on the road it doesn't respond, I'm litterally hitting my head against a brick here, everything just seem right I can't explain it.
I have done debugs and there is no sign of life, its as though when the vpn client connects to the router its not responding any way here is my config for the vpn clients part that is.
aaa new-model
!
!
aaa group server radius vpn-client-server-group-1
[Code].....
Cisco :: Set Up A SSL VPN Connection For Remote Connectivity With AnyConnect Client?
Jun 28, 2011I've been trying to set up a SSL VPN connection for remote conenctivitiy with AnyConnect Client. I've configured virtually everything necessary, I can connect to the VPN page, download the Client, establish connectivity, Get an internal-IP address. But I can't ping any internal (and of course external IP addresses)
View 12 Replies View RelatedCisco VPN :: ASA 5510 Access All Branches Using Remote Client
Jun 18, 2011I am having asa 5520 in my head office and in branches 2811 routers.i connected two branches with my HO through VPN.now i configured remote vpn client in HO asa . now i need to access all the branches using this remote client.how i create route in HO ASA.
View 7 Replies View RelatedCisco VPN :: Remote IPSec VPN - Windows 7 Client And ASA 5505?
Dec 20, 2011I have difficulties with configuring Remote IPSec VPN with Cisco ASA 5505 and Windows 7 native VPN client. My client PC gets VPN pool IP address, and can access remote network behind ASA, but then I lose my internet connectivity. I have read that this should be an issue with split tunneling, but I did as it is told here and no luck.On Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have internet connectivity (since client is using local gateway), but then, I cannot ping remote network.In log, I see this warnings of this type:Teardown TCP connection 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0:00:00 bytes 0 Flow is a loopback (cisco)I have attached my configuration file (without split-tunneling configuration I tried). If you need additional logs I'll send them right away.
View 4 Replies View RelatedCisco VPN :: ASA 5550 - Can Client Establish SSL To Remote Network
Mar 16, 2012Device asa 5550 - But can a Client establish a SSL VPN to remote network and devices on the remote network access local network printers? so you got one client one network A that creates a SSL VPN to network B , can network B be configured so that automatic job come across the same ssl vpn to a Different IP?
View 5 Replies View RelatedCisco VPN :: 887 - EasyVPN Client Cannot Access Remote LAN But Only Router?
Oct 26, 2010I am using Cisco configuration professional to set up one easy vpn server on 887-K9,vpn client can dial up the server successfully but can only ping router but on other lan. Looks like there is a nat issues between lan and vpn client?
View 5 Replies View RelatedCisco VPN :: 5510 Remote Access VPN / Ping From Client
Jul 26, 2011I'm configuring ASA 5510 Remote Access VPN, I can connect from Cisco VPN Client to the ASA VPN. I obtain from ASA some routes to inside networks, but I can't do any ping to those inside hosts. I have got those error in ASDM log file: [code]
View 1 Replies View RelatedCisco VPN :: ASA 5540 - Client On Windows 7 With No Remote Access
Feb 22, 2011Recently i have received one of my collegue's laptop that is running windows 7.I have installed cisco VPN client version 5.0.07.0290 on it and VPN client appears to connect to our ASA5540, but we are unable to connect (remote desktop) to any machines on our network as it does on our XP laptops. Furthermore, we cannot ping any as well. Also, while connected the Windows 7 machine is still able to access internet site as if split-tunneling was configured, which its not.
But after some searching , i found from "routeprint" output (shown below ) that my local internet gateway is prefered over the VPN gateway which is 10.10.4.1.Here 10.10.4.19 is the IP address assigned for VPN adaptor.
Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.2 25 0.0.0.0 0.0.0.0 10.10.4.1 10.10.4.19 100
But after i manually add the below route on windows 7 laptop , it started connecting to remote desktop successfully.
route change 0.0.0.0 mask 0.0.0.0 10.10.4.1 metric 20
But aftersome time of idle state , it is again going back to original route state of prefering the local gateway of 192.168.1.2 and thus unable to connect to Remote Desktop again.
Cisco VPN :: 5505 Using VPN Client To Access Remote Network Over L2l
Apr 3, 2013I´m tring to configure ASA 5505 with VPN Cleint, to access a remote network over a L2L with another ASA 5505, but no sucess. Is there any special feature to this work?
View 2 Replies View RelatedCisco VPN :: ASA 5505 / 5510 - VPN Client Accessing Remote LAN
Apr 2, 2012Trying to figure out how to configure the VPN client side to access a remote LAN.
Lan A - 172.16.17.0 - ASA5505 8.2(3)
Lan B - 200.200.0.0 - ASA5510
Cisco Client - V5
At present there exist a VPN tunnel between LAN A and LAN B. The client has a VPN tunnel to LAN A to run software package X on the LAN A server. The client also needs to run software package Y which needs access to a database on LAN B. The computers on LAN A have no problem using package Y since a VPN tunnel exist between LAN A and LAN B. How can I get the Client to also access LAN B on the same tunnel created when the client connects to LAN A? I can't seem to get packets that are directed to LAN B to cross the Client tunnel to A which would then hopefully move onto the LAN A/ LAN B tunnel.
Cisco Firewall :: Remote VPN User Client Type On ASA 8.3?
Jun 21, 2011It seemed that show vpn-sessiondb ra-ikev1-ipsec will not provide the client type of the remote vpn user as show vpn-sessiondb remote did before.
Is there a way to find it out on ASA running 8.3?
Cisco VPN :: ASA 5510 / VPN Client Cannot Access Remote Servers
Mar 27, 2011I have successfully installed and configured VPN Client - Version 5.0.07 to connect to ASA 5510 from a remote workstation. Here is the problem, I cannot ping any of the servers or workstations after I successfully connect. I can ping the ASA 5510 using its internal LAN IP, but no other nodes will respond on the remote LAN.
View 2 Replies View RelatedCisco Security :: RDP Access For Remote VPN Client On ASA 5510?
Jan 17, 2011We have configured site to site VPN tunnel from offshore to client location using ASA5510 and accessing RDP from client location. Also configured remote VPN access at offshore location. But using remote VPN client we are able to get RDP from officeshore location but not able to access RDP from client location. Is there any additional changes required ?
View 4 Replies View Related