Cisco VPN :: 5540 - Prompting For Domain Name When Requesting Authentication To User

Jun 26, 2011

I have a remote access VPN profile configured on an ASA 5540. This profile is almost identical to the same profiles configured on other ASA 5540. The profile is linked to Active Directory for authentication. For some reason, users are not being prompted for the domain name field when connecting to the firewall, on the other firewalls they get prompted for all three (user/pass/domain).
All the firewalls are running 8.0(4) 32. And the following is the configuration of the firewall that I am experiencing issues with:
ip local pool TESTVPN mask
group-policy TESTCERT internal
group-policy TESTCERT attributes
banner value **** WARNING ****
banner value You are Now Successfully Connected (code)

View 1 Replies


AAA/Identity/Nac :: ACS 5.1 Domain User Authentication Restriction

Sep 26, 2011

We have configured ACS 5.1 for autenticating wireless users with active directory, which is working fine now.But we would like implement that single user should be authenticated through ACS . If any user try to access WLAN from multi system will be notified with multi login access restriction.Can we implement this policy in acs, if possible what are the exact configuration changes we have to implement.

View 1 Replies View Related

AAA/Identity/Nac :: ACS 5.1 Authentication From Cross Domain User

Dec 28, 2011

We have cross domain trust relationship established and I have added the user group in our ACS 5.1. we are using Active directory as an external Identity store. Also I have created a rule in the 'Access polices' to allow the user group. From the cross domain, I use as a user id, but I get this error message 13036 Selected Shell Profile is DenyAccess.

View 3 Replies View Related

Access Domain Network Shares Without User / Password Authentication?

Sep 21, 2011

I`ll get straight to the point. I have at work a domain of computers. on one of the computers (I have admin rights) I want to share a folder that can be accessed by other computers that are not in the domain. By default accessing that share requires a user/pass. My question is: can I configure something on the computer (running windows 2008 server) to the shared folder so that other computers that are not from the domain will gain access to without user/pass requirement (like a normal share)?

View 3 Replies View Related

Linksys Wireless Router :: RE1000 Wired PC Prompting User For Login Information For Wireles

Oct 30, 2012

I recently installed an RE1000, which seemed to be working fine. Then, on 3 PC's with no wireless adapter installed we began being prompted for user name and password for the wireless router. Once I unplugged to extender the problem went away. I know what you're thinking: Maybe I just think there's no wireless adapter on these PC's. NO, I looked in device manager and the only network adapter installed is the ethernet adapter. These are all 4+ year old machines with no hardware changes made to them. Wireless adapters are not necessarily standard issue on old towers--even on new towers. The Acer I'm using right now was purchased new in November 2011 and did not come with a wireless adapter installed.

View 3 Replies View Related

Cisco VPN :: 5540 Stop Split Tunnel For Only One User

Apr 18, 2013

 i have cisco asa 5540, users access vpn through anyconnect, i have applied split tunnel so that all users accessing internal network ( grows through tunnel and other traffic through internet.. working fine.i want to fully tunnel one user so that all his traffic goes through the tunnel, what is the best way to do it, "is there any guide (step by step)"

View 3 Replies View Related

Cisco VPN :: ASA 5540 AnyConnect Client Certificate Authentication

Jan 22, 2012

I want to connect with AnyConnect Secure Mobility Client 3.0.2052 to ASA 5540 Version 8.4 and SSL Premium License.The clients using Maschine Certificate to authenticate to ASA. This works fine.Now I want to setup a DAP to verifiy the client against the Microsoft AD using LDAP. I configured LDAP server in ASA see:aaa-server LDAP protocol ldap aaa-server LDAP (inside) host ldap-base-dn DC=x,DC=x,DC=x,DC=com ldap-scope subtree ldap-login-password ***** ldap-login-dn ***** server-type microsoft ,I can see that it works if I test the server via the testbotton in ASDM and I see it in CLI "debug ldap 255" also. But if I configure in DAP: AAA Attribute ID:memberOf = DomainMember I can not see any request to the LDAP server during I try to connect with the Client und the DAP doesn't match.

View 2 Replies View Related

Cisco Firewall :: 5540 - Remote VPN Authentication Fail?

Mar 15, 2011

wht would be change on configuration of remote access VPN on asa 5540.
4|Mar 16 2011|15:26:01|713903|||Group = tesTGroup, Username = GSDc2gsIdc, IP =, Error: Unable to remove PeerTblEntry3|Mar 16 2011|15:26:01|713902|||Group = tesTGroup, Username = GSDc2gsIdc, IP =,


View 3 Replies View Related

Cisco VPN :: 5540 ANyConnect Client Certificate Authentication

Jul 13, 2011

want to connect with AnyConnect Secure Mobility Client 3.0.2052 to ASA 5540 Version 8.4 and SSL Premium License.The clients using Maschine Certificate to authenticate to ASA. This works fine.
Now I want to setup a DAP to verifiy the client against the Microsoft AD using LDAP. I configured LDAP server in ASA see: [code]I can see that it works if I test the server via the testbotton in ASDM and I see it in CLI "debug ldap 255" also. But if I configure in DAP: AAA Attribute ID:memberOf = Domain Member I can not see any request to the LDAP server during I try to connect with the Client und the DAP doesn't match.

View 3 Replies View Related

User Cannot Log Into Domain?

Mar 22, 2012

I have a Active Directory user that cannot log onto any computer that's on my organizational domain. The error is "You cannot log on because the logon method you are using is not allowed on this computer"

View 5 Replies View Related

Cisco VPN :: ASA 5540 - Client IPsec Authentication Using Digital Certificate

Sep 11, 2011

I need some clarification with configuring my ASA 5540 with IOS 8.3x for remote client certificate authentication.
I have my root certificate from the Microsoft CA but not quite sure if the outlined steps in the Cisco websites below are exactly what I need since the firewall seems to be generating the certificate to be used. [URL]. 
My setup is such that the CA will issue certificates to the remote clients and to the ASA firewall, and the remote clients will authenticate and connect with their certificates which the firewall constantly updates using the CRL update from the CA. The dhcp pool is to be issued by the domain controller on the inside network and not on the firewall. Any examples or best practice steps to achieve this.

View 8 Replies View Related

Changed Domain For Workgroup / Can't Log Into User

Jan 29, 2012

We have a computer running Windows 2000 Pro that used to connect to a domain at work. Upon bootup, it asks for the user/password.Yesterday we tried to connect it to a little home network by changing the domain to a workgroup with a different name (network name that i used at home) as well. Now when it boots up, asks for a user/password, but now it does not recognize my user name and password.I can log in as an administrator to the Workgroup with the new name. but i cannot access the old Domain with its user and passwords. I tried to change back to the old name and to domain, but when doing that i get and error messsage which says: The following error occurred validating the name "xxxxxxx" (network name that I use at home) this condition may be caused by a DNS lookup problem. so I'm not sure if a should run the clear DNS cache. and if in doing that I'll be able to restored it back to the stage that i was before I made the changes.

View 1 Replies View Related

See Which User In My Domain Modified Folders?

Sep 28, 2012

We have shared network drives on my network whose folder structure must not change. We have users who must have full access to the contents of these folders and be able to read/modify/erase and create new files inside these folders. However, the structure of the folders must not change so that other users/programs can locate files within these folders.

Some users sometimes "aggressively click" and drag and drop folders into different locations and can't remember where they dropped them. This makes them inaccessible for other users. We have a lot of folders so I implemented FileWatcher Simple program to monitor these folders and if there is a change in folder structure I get an email with an attached log. The log tells me which folders got created/deleted/renamed and I am able to restore the folder structure if need; but I cannot see who caused these changes.

1. Is there a way for me to see which user in my domain modified the folders?

2. Is there a way to disable users from drag and dropping, deleting, renaming folders yet still maintain full access to the files within these folders?

View 1 Replies View Related

Cisco VPN :: ASA5510 Anyconnect Permission With NT Domain User

Aug 21, 2012

I am trying to setup a VPN with AnyConnect on my ASA5510 and it works fine.  I have setup an AAA server group for my Active Directory with the "NT Domain" protocol".  Right now, every user is able to connect with their Active Directory credentials.  I would like to restrict access to the Anyconnect VPN to only a few users in AD.

View 1 Replies View Related

Cisco AAA/Identity/Nac :: ACS 4.2 Multiple AD Domain Authentication?

Feb 3, 2013

I have acs 4.2 for windows installed on a windows server 2003 box, because of a merger I need to now authenticate against 2 different domains, there is a bidirectional trust between the two domains and the dial-in permission has been set in ADUC but whenever I try to authenticate a user it says dial-in permissions needed in the acs failed authentication log.

View 5 Replies View Related

How To Find Current Logged On User In Domain Network

Aug 22, 2011

how to find the current logged on user on a domain network? I tried nbtscan but it gives me ip address, machine name and mac address. In the server column it gives <server> and in the user name column it give <unknown>.

View 1 Replies View Related

2008R2 / Cisco2960 - Why Can User Log Into A Domain Account When The Server Is Down

Jan 13, 2012

We had a power outage that kicked off our server and our network switch (2008R2, Cisco2960), before we could get it back up, a user was able to log into his laptop.

The user used the domain login - not the local machine account - he obviously wasn't able to access any shared resources, but how did he log in with a domain account, when the server and switch were both off?

View 1 Replies View Related

Sharing :: How To Grant Permissions For Domain User To Directory

Jun 29, 2012

I started getting into IT (as a job) a little less than a year ago, though I've been working with computers for close to 20. So networking was never something I was into while working on computers at home. I've been handed a significant position at work and I am learning a lot as I go. I want to know how to grant permissions for a domain user to a directory without adding the user to all of the sub-directories and directories. The only way I've figure thus far is to grant permissions to said folder, then inside remove the "inherit permissions..." but then I have to manually remove the permissions to every other sub-folder.I want to add a single path to a folder by adding single permissions to each folder until the directory in question is reached.

View 2 Replies View Related

User Can't Login Into Domain With Right Credentials In Active Directory

Feb 19, 2013

user can't login into domain with right credentials in active directory

View 6 Replies View Related

Making A User A Domain Admin In Server 2003

Jul 20, 2011

I have a desktop without a wireless card and i want my network to be wireless so i bought a d-link wireless card for the desktop, the system then discover the wireless network but could not connect it kept on trying to authenticate, it did not even ask me for the web security key, what do I do

View 1 Replies View Related

Cisco AAA/Identity/Nac :: ACS4.2 Windows Authentication To Other Trusted Domain?

Jun 6, 2011

I'm installing ACS4.2 in our lab domain and want to leverage the corporate domain for authentication.  The one way trust is in place, but there is a facet that I'm not clear on in regards to the installation requirement.
I'd like to install ACS on a lab domain member server, but I'm not sure that will work.  The installation docs seem to imply that a member server must be in the same domain as the authentication server, but its not very clear. if I want to use the one way trust to the Corporate Domain, am I required to install ACS on the domain controller of the Lab Domain?

View 3 Replies View Related

TMG Wont Allow Wireless Router To Give Internet Without Authentication Domain?

May 20, 2012

A wireless router linksys has been installed but the internet through that wireleless works only if i type the proxy on the IE browser and authenticate with domain

View 1 Replies View Related

Cisco VPN :: ASA 5510 VPN User Authentication

Apr 5, 2011

We are changing our old Pix 515e this weekend and for brand new ASA 5510.With this new installation, I would like to implement the Radius authentication for remote vpn user. Changing the firewall of the company has many impact and for the first phase the user will keep authenticating locally but I need that in phase 2, they will be authenticated via a radius server.Is there a way to configure both authentication for remote vpn user?
All user will be authenticated locally except the member of the IT Department who will be authenticated by the radius server for testing.I have remote vpn users around the world so I do not want these users to be blocked by the testing of the radius authentication. What I want is that users in group1 will be authenticated locally on the ASA and users in group2 will be authenticated by the radius. When testing will be done, all users will be transfer to the radius authentication gradually.

View 1 Replies View Related

Cisco :: 440 No Authentication Requested After A User Reboots

Jun 1, 2011

On our guest wireless, at times when a user shuts down their laptop and powers back up they are not asked to re-authenticate.The only security is a login and password then the user is tunneled to our 440 in our DMZ then out the internet pipe.My question is if the user shuts the laptop off then starts it back up shouldn't they be prompted for the user login and password?

View 2 Replies View Related

Cisco VPN :: ASA 8.2 Anyconnect User Authentication And Authorization

Jan 17, 2012

I would like to configure RADIUS authentication and authorization in ASA 8.2 (ADSM 6.2) by configuring Cisco anyconnect VPN client connection profile.So the end result would be user enters his username, password and a token in any connect client, then the RADIUS server validates this information and sends the user attributes to ASA upon successful authentication.I would be grateful if i can get the step by step procedure to achieve this:The below is what iam trying to do:

1) Create an AAA server group.
2) Add the AAA server to this group (here its RADIUS).
3) create an LDAP-cisco ASA group mapping (for authorization)
3) Add a group policy and create IP pool. (We can add two types of group policies, one is internal and external. Not sure which one to select here).
4) create a any connect vpn client connection profile. Here we specify the created server group name, IP pool and group policy.(While creating a connection profile, it asks us to select an interface. As of now i have only one interface which is "inside". Not sure what the interface "outside" means).

View 5 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.3 Local User Authentication

Nov 12, 2012

I want to have a local user in ACS that is permitted to login to routers. I have TACACS with AD already working but cannot get a local user to work. I used to do this in ACS 4.x.I created a user in the internal identity store.I tried configuring a policy to allow this users TACACS authentication multiple ways to no avail. I cannot find a config example doc and cannot figure it out from the user guide as the documention is sorely lacking.

View 5 Replies View Related

Cisco Wireless :: WLC 2106 Only One User Authentication

Mar 4, 2010

I have a WLC 2106 and's a hotspot configuration.So in WLC, under controller tab, i have set my ap-manager ip, my management ip, my virtual ip ( and my hotspot network range ip.I set also a DHCP range for the hotspot network.
In Wlans tab, i set my hotspot wlan, with no layer 2 security and for layer 3, i set none for layer 3 security and i use web policy authentication.I use local authentication and i created under security menu, under AAA tab, 3 local net users.
From pc number 1, i get ip from dhcp, and i have authentication web page, authentication is ok and i can surf on web.From pc number2, when user 1 from pc 1 is connected, i get ip from dhcp but i have not the authentication web page, i have not DNS resolution.when i try https:, i have no answer.
And when user 1 is de-authenticated, the user 2 can surf on web.So only one user can surf at the same time. not good for a Hotspot.

View 12 Replies View Related

AAA/Identity/Nac :: ACS 5.2 Machine Authentication And AD User?

Sep 1, 2011

I am trying to setup up a rule to allow wireless access only to users in my AD when they use computers from my AD.I have Machine authentication working on it's own (computer boots up and connects to wireless - confrimed by ACS logs) I have User authentication working But when I try to creat the floowing rule:it does not work.
Access Policy
Access Service:
Default Network Access Identity Store:
Authorization Profiles:
Exception Authorization Profiles:
Active Directory Domain:

Everything seem to fine until it gets to the last rule.

View 1 Replies View Related

Cisco AAA/Identity/Nac :: Can Use ACS 5.2 As Guest User Authentication Server?

Jun 5, 2012

Can use ACS 5.2 as Guest user authentication server?

View 3 Replies View Related

Cisco AAA/Identity/Nac :: ISE / Machine And User Authentication / MAR / Timeout?

Apr 12, 2013

I am using ISE first question:I want to know the relation between the attribute "WasMachineAuthenticated" and the MAR (MAchine access restriction in advanced setting for AD).Is-it the same  or not ?Once you time out, you need to do machine auth again. What is the timer ?Using the attribute "WasMachineAuthenticated", is-it the same timer that you configure in MAR ? In a distributed environnement, is the information about machine previously authenticated  replicated to all policy node ?Because, if a swicth has 2 radius-server, we are not sure that it will point everytime to the same server.

View 1 Replies View Related

Cisco Wireless :: How To Set Up User Authentication On Aironet 1200

Jan 22, 2013

I would like to be able to have a few "guest" users on the Wireless network for visitors. Is there any method to have a prompt for "Username / password"? I would like the user accounts to have different expiry periods if this is possible. My current config is attached. The SSID "test" appears on the network. The SSID "test111" does not appear.

View 1 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.2 - How To Bind User Authentication And Machine

Jul 18, 2011

For our wireless, we enabled the machine authentication, but we want to bind the machine authentication and user authentication together which means they need to meet both requirements to access the wireless, how can we do this? Right now looks like as soon as the machine is authenticated, it can access the network, no user authentication needed.

View 6 Replies View Related

Cisco AAA/Identity/Nac :: How To Configure User Authentication Via TACACS On UCS 1.4 With ACS 5.2

Aug 18, 2011

how do i configure user authentication via TACACS on UCS 1.4 with ACS 5.2?  My TACACs connection works, and my user authentication is successful, but i can only get read-only rights.  I have tried several versions of "cisco-av-pair= role=admin" both as mandatory attributes named role and as cisco-av-pair=role , with "admin" as the value, and i still get read-only.
When i attempt to find any documentation, it only describes ACS 4.2, which is another problem i have with most documentation for new cisco products (i have this exact issue with my NAMs, nothing i do to change the attributes results in successfully logging into the NAM, and all config guides are written in 4.2 speak).
is there any possiblity cisco is going to release some documentation on how to convert 4.2 speak to 5.2 speak?

View 8 Replies View Related

Copyrights 2005-15, All rights reserved