I have created a Remote VPN connection on a Cisco ASA 5505.When I'm connected remotely through the Cisco VPN Client my connection is very slow.I have a response time of 220ms when I ping my server. how to improve the speed of the VPN connection?
View 1 RepliesI have a question on a VPN connection. I have a remote access VPN setup on an ASA 5505 to be able to remote into a location and check the HVAC program running on a PC. The remote connection connects fine, but when I use remote desktop to connect to the PC, it connects quick, but the screen redraw and reaction time is extremely slow. EG: I click on the program and it takes about 20 seconds to draw the screen, or I click on a menu bar and get the same times for reactions. Could this be a ISP Up/Download issue or is there something that I need to look at on the ASA to change?
If I connect to the remote and do a PING from my desktop to the remote Desktop, these are the results that I get:
Reply from 192.168.XX.XX: bytes=32 time=96ms TTL=128
Reply from 192.168.XX.XX: bytes=32 time=132ms TTL=128
Reply from 192.168.XX.XX: bytes=32 time=90ms TTL=128
[Code]......
I created three different Remote VPN connections with three different networks . i can make them one but for some reasons i don't mix all.and iam using Cisco asa 5505 with Shrew Soft VPN software , so my problem is,- i connected Shrew soft remote vpn , if i try to connected another remote vpn connection this will not accept the second connection, any remote vpn connection software that accepts more than one connection
View 1 Replies View RelatedI have setup a vpn connection at my remote offices with a 5505. At my main office I have a 5510.From my remote offices I can PING my Main office server. However when I go to set up a vpn connection through windows network and sharing center I can't seem to have the connection connect.....
View 15 Replies View RelatedI have been working with my ASA 5505 VPN Concentrator to maintain a connection with one of my remote sites. I have several tunnels that work fine and dont have any issues at all, but one tunnel with outside IP ending in 146 and inside LAN 192.168.3.0 goes down every 24 hours. Attached is the config from the concentrator. I changed around the Security Association Lifetime Settings and the tunnel would drop after that amount of time expired. If I set it to 24 hours, the tunnel would drop every 24 hours. If I set it to 8 hours it would go down every 8 hours.
I have swapped the router a few times, double and triple checked my key settings, disabled keep alives on both ends, and this problem just started happening a few weeks ago after working fine for years. I also get the following e-mail error every time it goes down:
<161>Jul 10 2011 16:19:47: %ASA-1-713900: Group = xxx.xxx.xxx.146, IP = xxx.xxx.xxx.146, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies View RelatedOn wireless (lenovo tabletx61) I cannot connect through the intranet - no problem connecting through internet. When I manage to connect through intranet connection is dropped quite often.No problem connecting via Ethernet cables.
View 1 Replies View RelatedCurrently, my work computer has (obviously) a local desktop. Also, we use a Remote Desktop for our shared network drive (our head office is on the other side of the country). The annoying thing is that if I am looking up a document on the share drive (Remote Desktop) and I want to work on it, the Remote Desktop applications are slow. So I'd rather work on it on my local desktop. However, I have to email it to myself, exit the Remote Desktop, retrieve it from my mail (in local desktop) and then save it
View 2 Replies View RelatedI'm accessing a NAS server remotely through VPN (Netgear FVG318). I can connect to the NAS server but it is very slow when opening and saving documents. When accessing the network drive I am connected to the Internet through wireless connection. When I connect to the Internet through Ethernet cable opening and saving documents is much quicker. Is there anyway I can make the remote access quicker when accessing it through a wireless connection?
View 1 Replies View RelatedI have created Remote access vpn on ASA 5505 (ver 8.2(5) with base license). When I connect from one machine, I can ping the internal network. But when I connect from another machine, cant.I have only decrypts on the ASA side, without encrypts. I was debugging ICMP packets with the capture feature, and saw that echo-reply packets are returning toward the outside interface, but aren't passing through it.
capture test access-list test interface outside
1: 08:54:44.298980 802.1Q vlan#1 P0 x.x.x.x > y.y.y.y: icmp: echo reply
Where x.x.x.x is LAN and y.y.y.y is the VPN client ip. The nat is ok, access lists are ok, but the packets dont pass through.I tried creating new VPN profile but the same problem, it seems that only one remote client can be active even base license allows more than 1 client.
I have 2 ASA5505 firewalls deployed, 1 at the data center (code v8.0.3) and 1 at a remote location (code v8.0.2). The remote location has 2 PCs that connect back to the data center to access the directory services, exchange, file servers, etc. The ASA5505 firewalls are configured for a site to site VPN.We were having stability issues with the remote ASA so we decided to upgrade the code as a first step. We updated the data center to 8.0.5 and all was well. I data was flowing and I could get into both ASAs from the data center via ASDM and ssh.Then I updated the remote location to 8.0.5. Now I can't ASDM or ssh into either ASA unless I'm at that specific site. PCs are still able to connect their servers.
I am unable to ping, telnet, ssh or ASDM into the inside vlan ip address while I am at the other site. I can see in the logs inbound connections being built on the distant firewall but it doesn't build a new outbound connection to reply traffic.Did 8.0.5 do something to block management connections from the outside?
Got a single asa 5505 configured in the office. we have 3 site to site vpn connections from this device, which all work from within the office.Ive not setup my pc to connect from home to the asa via the ciso client.
i can connect to all LAN servers on the local subnet, however i cannot connect through the ASA to any of my site to site vpn's.
if i do an ipconfig on my home pc i can see my local ip, mask & gw, and i can see my assigned remote access ip & mask but no gw.
I cannot ping any remote site to site pc's by IP or name.
There is a site I oversee that is moving to a new ISP. The drive is 2 hours round trip and I need to do is change an IP. DHCP is being handed out by the internal Domain Controller and all the workstations point to the server for DNS. Will the following commands inputted over an SSH putty session into the current WAN IP change the IP and allow me to hookup to the new ISP? The plan is to copy and paste the following commands into global config mode. Currently they are using DHCP on the WAN side which I do not approve of and their external route is pointing to the internal IP of 192.168.1.1. Things still work but I want to do away with this. Will these commands get the job done?
interface vlan 2ip address 68.x.x.2 255.255.255.240exitno route outside 0.0.0.0 0.0.0.0 192.168.1.1route outside 0.0.0.0 0.0.0.0 68.x.x.1
I am currently having an issue configuring an ASA 5505 to connect via remote access VPN using the Cisco VPN Client 5.0.07.0440 running on Windows 8 Pro x64. The VPN client prompts for the username and password during the connect process, but fails soon after.
The VPN client logs are as follows:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
2 15:09:21.240 12/11/12 Sev=Info/4 CM/0x63100002
[code]....
We have a ASA 5505 in our enviroment. We already configures two site 2 site VPN to our branch offices. Now we are planning to configure remote access VPN. So what should be consider when configuring the remote access VPN in ASA which already having site to site VPN?
View 9 Replies View RelatedI have Cisco ASA 5505 and i want to create vpn remote access ...l
so i created and connected to the vpn ...my problem is to reach my Local connection of 192.168.1.0 /24 i put the WAN Connection in the FA0/0 and put my LOCAL AREA CONNECITON into FA0/1 .. so how i can route or translate my connection , and using cisco ASDM 6.1 in GUI ,,,
I have set up two ASA 5505's (lets call them ASA1 and ASA2) with site to site VPN configuration and i've encountered two problems with my setup.ASA1 has IP 192.168.1.254 on the inside interface and is connects ASA2. It's also an Easy VPN Server for external users to connect through Easy VPN Client.ASA2 has IP 192.168.11.1 on the inside interface and connects to ASA1 Problem #1 None of the ASA's can ping eachothers inside LAN IP address. Computers behind the ASA's are unable to ping the remote ASA's inside IP address. My guess is that this has to do with either NAT or built in security.Problem #2. The Easy VPN clients which connects to ASA1 are unable to access the LAN behind ASA2.
View 3 Replies View Relatedconfiguring ASA 5505 to be able to ping remote host.Setup - We have a site-to-site (192.168.1.0/24 - 192.168.2.0/24) VPN setup with client VPN access (IP Pool, 172.16.50.0/24) on 192.168.1.0 ASA 5505.Issue - Not able to ping host on 192.168.2.0 from VPN client 172.16.50.0 but able to ping 192.168.1.0 host.
View 8 Replies View RelatedWe have 3 offices, each with an ASA 5505 as the router/firewall, connected to the cable modem
(NC office) <----IPSEC----->(PA office) <----IPSEC-----> (CT office)
Internally we have a full mesh VPN, so all offices can talk to each other directly.I have people at home, using remote access VPN into the PA office, and I need them to be able to connect to the other two offices from there.I was able to get it to work to the CT office, but I can't get it to work for the NC office. (What I mean is, users can remote access VPN into the PA office, and access resources in the PA and CT offices, but they can't get to the NC office).
Result of the command: "show run"
: Saved:ASA Version 8.2(5) !hostname WayneASA
names!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip address 70.91.18.205 255.255.255.252 !ftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns domain-lookup insidedns domain-lookup outsidedns server-group DefaultDNSname-server 75.75.75.75name-server 75.75.76.76domain-name 3gtms.comsame-security-traffic permit intra-interfaceobject-group protocol TCPUDPprotocol-object udpprotocol-object tcpaccess-list inside_access_in extended permit ip any any access-list IPSec_Access extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 access-list IPSec_Access extended
[code].....
i want my ASA 5505 8.2(5) to access my proxy server on remote lan through VPN my VPN is OK, all PCs of local network can access to remote network.but ASA on local network can't access to remote network.i think it's a NAT problem but ....
local network 192.168.157.0/24 local IP ASA 192.168.157.1
remote netword 10.28.0.0 /16
remote proxy 10.28.1.26
my conf
[code]....
I just made a VPN on my ASA 5505 at home, I can connect successfully to it, but I can't contact anything in the network, nothing respond to ping or to anything else (include the ASA inside IP).
View 3 Replies View RelatedI have 3 networks coming from the DMZ (VPN) and only one works:10.132.24.0/24 Not working10.132.25.0/24 Not working10.132.26.0/24 Working The thing is, the one that works is on the same network as the DMZ(VPN) interface. The other two do authenticate and they get an IP from the VPN Pool. but they just cant access anything.
View 11 Replies View RelatedI try to configure a simple EzVPN infrastructure:
EzVPN Server (CISCO2811, hostname cme) < -- > EzVPN Remote (ASA5505, hostname ezvpn-asa) < -- > Client
Attached you find both configuration of the EzVPN server and remote. The tunnel is getting up and if I ping from the ASA to the Router, I see the packets getting encrypted:
ezvpn-asa# ping 172.16.100.1
...
ezvpn-asa# show crypto ipsec sa
interface: outside
Crypto map tag: _vpnc_cm, seq num: 10, local addr: 172.16.100.2
[code]....
If I connect a client with IP address 192.168.1.2 to the interface eth0/1 and do a ping to the cme, I don't see any packets getting encrypted. I don't have any idea about VPN, I just need it for a wireless lab environment. What do I have to configure on the ASA, so the inside traffic is encrypted?
I have not really set up ASAs nor VPNs on Cisco devices before. I'm currently attempting to configure a remote access VPN between ASA devices, a 5505 and a 5510. The 5510 is meant to be the server and the 5505 is meant to be the easyvpn client. The reason I am opting for remote access as opposed to site to site is that I have many 5505s at remote sites that I will need to configure in the future, and they will be moving around a bit (I would prefer not to have to keep up with the site-to-site configs). The 5510 will not be moving. Both ASA devices are able to ping out to 8.8.8.8 as well as ping each other's public facing IP.
Neither ASA can ping the other ASA's private IP (this part makes sense), and I am unable to SSH from a client on the 5510 side to the 5505's internal (192) interface. I have pasted sterilized configs from both ASAs below.
ASA 5510 (Server)
ASA Version 8.0(4)
!
hostname ASA5510
domain-name <domain>
enable password <password> encrypted
passwd <password> encrypted
[code].....
I try to configure my CISCO ASA 5505 for remote access vpn, and I encounter the following issue : Secure VPN Connection terminated locally by the Client. Reason 412: The remote peer is no longer responding. [code]
View 2 Replies View RelatedIs there a way I can configure a remote access VPN on a Cisco 5505 using digital certs instead of pre-shared key. I dont want to use a 3rd party CA, can the ASA perform this role? with a self signed cert?
View 6 Replies View RelatedI have an ASA 5505 that is on the perimeter of a hub & spoke vpn network, when I connect to this device using the VPN client I can connect to any device across the VPN infrastructure with the exception of the sub net that the client is connected to, for instance:
VPN client internal network connects to 192.168.113.0 /24 and is issued that ip address 192.168.113.200, the VPN client can be pinged from another device in this network however the client cannot access anything on this sub net, all other sites can be accessed ie. main site 192.168.16.0/24, second site 192.168.110/24 and third site 192.168.112/24. The ACL Manager has a single entry of "Source 192.168.113.0/24 Destination 192.168.0.0/16 and the "Standard ACL 192.168.8.8./16 permit.
I had a previous issue in which I couldn't make a connection to an ASA 5505 behind an edge firewall found here: url...My continuing issue is that I can indeed connect to the ASA 5505 remotely but I cannot access anything internally. I believe it is a NAT issue but as of yet, nothing has worked.
View 1 Replies View Relatedunresponsive / lockups with Cisco ASA 5505 remote management ?
I think it happens like this:
1) With ASDM (Java Web Start), add new crypto map (it could be anything, just happens to be what i added the last time this happened)
2) Click apply
3) ASDM hangs (at this point the Java client becomes entirely unresponsive)
4) ASDM.jnlp refuses to connect and eventually timeout dialog appears. However, VPN connections are still accepted.
5) After a few hours (over night), the ASA refuses all incoming traffic including VPN connections.
I have a remote ASA5505 running 8.4(3) with a working site 2 site VPN tunnel to my main office. (The main office is running an ASA 5510 with OS 8.4.3 as well). The encryption domain is all private IP on main site vs. 172.16.10.0/23 on remote site.
Relevant config of the remote ASA:
interface Vlan1
nameif inside
security-level 100
[Code].....
I can manage the ASA on the outside interface (outside of the site 2 site VPN) using the TACACS credentials I can also ping my management station from the ASA using the inside interface, but as stated, the other way around does not work. I have not yet tested if management from the local 172.16.10.0/23 subnet works, but I will try this next.
I have an ASA 5505 running 8.2
I used the ASDM wizard (6.3) to set up a remote VPN. After slightly adjusting the wizards configuration the VPN is working well.
Now I need to change the Outside interfaces IP address. When I do that the VPN no longer works. If I change it back to the original value the VPN works again.
What configuration changes do I have to make regaurding the remote VPN after changing the outside interfaces IP address?
Users are connecting to Site A (PIX 515e) via Cisco VPN client and can access servers/resources within that site no problem. They cannot access anything within Site B (ASA 5505) however. Devices communicating between Site A and Site B have no issues (have site to site VPN configured). I'm assuming that I'm missing something in configuration - or is it not possible for VPN clients connected to the PIX firewall and access data on the other network?
View 1 Replies View Relatedi have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration
ASA Version 8.2(1)
!
!
interface Vlan1
[Code].....