Cisco :: VPN-PassThrough With Wlc 5508 7.0.235.0
Nov 20, 2012
i have 2 ssid with the same comfiguration (diff only in name) in one ipsec ssid vpn (l2tp over ipsec with natt ) works fine, in another after phase 2 is completed no traffic is forwarded and vpn session is dropped. There are no access lists on equipment.
I found in documentation that need to activate L3 security and set it to vpn pass-through, but in drop-down menu only one item "none". What is the reason to drop ipsec traffic ?
View 4 Replies
ADVERTISEMENT
May 16, 2012
I have a guest wireless network setup on a 5508 WLC using 7.2.103.0 firmware. Under my guest WLAN>security>Layer3 tab I have "layer 3 security" as "none", "web policy" as check marked, "passthrough" selected, "over-ride global config" as check marked, "web auth type" as "customized(downloaded), "login page" and "login failure page" as "login.html" selected.
I haveI have 4402 WLC's using 7.0.116.0 firmware throughout my company that anchor back to the 5508 for the guest network. The 4402 WLC have the guest network configured as WLAN>security>Layer3 tab I have "layer 3 security" as "none", "web policy" as check marked, "passthrough" selected.
I would like to disable the HTTPS for the logon screen and I am not sure what steps need to be done for this. I researched and found the command "config network web-auth secureweb disable". I set the command on the 5508 only and rebooted. When I tested I got a blank webpage with "http://1.1.1.1/fs/customwebauth/login.html?switch_url=http://1.1.1.1/login.html" in the address bar and had no way of clicking the accept button to get to the Internet.
Everything works fine again if I enter "config network web-auth secureweb enable" and reboot. Do I need to run the "config network web-auth secureweb disable" command on all the 4402 WLC's that are anchored to the 5508? What could be breaking my login.html page while using only http?
View 3 Replies
View Related
Jul 18, 2012
I have a Cisco 5508 running version 7.0.116.0. This controller hosts an open public wifi that requires users to accept a terms agreement via a Web-Passthrough setup that redirects them to the terms splash page. For most people this works without any issue. However, if a user has their homepage for their default browser set to a https site, such as [url]..., then they are never redirected to the terms splash page. The page will just spin and spin until finally they get a timeout error.
View 7 Replies
View Related
May 9, 2013
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
View 1 Replies
View Related
Aug 22, 2011
I have a DIR-655_RevB updated with the latest firmware 2.03NA. I have two VPN devices in my house trying to get to my corporate office: a VPN phone and my laptop with a VPN client, both use IPSec. Either device has no problem making a solid VPN connection separate from each other. Meaning that when my laptop is not connected, I can connect the VPN phone with no problem. And when the VPN phone is disconnected, the laptop also has no problem making a solid and stable VPN connection. So I know the router is configured correctly to let thru VPN traffic for either device. i.e. IPSec is enabled, UDP/TCP Endpoint Filtering are both set to Endpoint Independent (and I've tried every other combo), SPI is disabled.
The problem is that I need to have both devices connected simultaneously, which this router is supposed to handle. If I have the VPN phone connected first, then when I launch the laptop VPN client, the VPN phone gets disconnected. I'm assuming that at this point, all VPN traffic is being tunneled back to the laptop. I cannot re-establish the VPN phone connection until I disconnect the laptop client, at which point the VPN phone "automatically" reconnects (meaning I don't have to reboot it, the VPN traffic just somehoe gets redirected back to this device)
View 7 Replies
View Related
Jan 13, 2012
In a cisco firewall 5520 how could you take a public wan connection and pass it to another firewall behind the 5520 without using nat. How could you put a single port on the 5520 into transparent or passthrough much like you can on a broadband modem?
View 3 Replies
View Related
Apr 10, 2012
How to enable PPTP passthrough on Cisco ASA 5505?I have a RRAS server inside and the client is trying to connect from outside.
View 1 Replies
View Related
Feb 26, 2012
I'm having some issues with Web-Passthrough, I'm using two 4404-50 controllers. Clients get IP addresses well. I'm using the controllers internal DHCP Servers. Controllers can reach DNS public IP Addresses (from management and guest vlan), the issue is that only very few clients are able to get displayed the Web-Passthrough page, the rest of the clients never get the page.
Version 7.0.98.0
The controllers also work as anchor controllers for two more foreign controllers.
View 10 Replies
View Related
Jan 24, 2013
I have a pair of ACE 4710 and I think I have all the failover configured correctly and it all appears to be working. My question is regarding setting QOS on the physical interfaces that are part of my port channel. I have qos trust cos enabled on all the interfaces in my port channel. These interfaces are connected to a 3750 swith. Do I need to configure QOS on the 3750 to allow the COS bit to pass through my 3750 to my peer?
View 3 Replies
View Related
Feb 6, 2012
I have a cisco 2504 running 7.0.220.0. I am trying to configure Web Auth for External Redirect, Passthrough. I have a page created on an external web server that was taken from the Web Auth Bundle and modified. It is a simple "accept" or "reject" on a Terms and Conditions page. I have a Pre-Auth ACL configured to only allow communication to the server the T&C page resides on.
When I connect to the SSID, the page redirects to the external URL and the the URL shows up in the browser window with all the variable data as a GET on the URL line, but the page never loads. It just hangs. I can copy the the URL data, paste that in once I am on-net, and the page loads just fine.
So, something is happening when the WLC is attempting to proxy-redirect the page back to the client.
View 7 Replies
View Related
Feb 10, 2013
I add a new Cisco ASA 5505 as firewall in of company network. I found the PPTP authentication did not get through to internal Microsoft Server.
ASA Version 8.4(3)!names!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1switchport access vlan 2!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip
[Code]....
View 4 Replies
View Related
Mar 28, 2012
I am working on IPSec Passthrough on an ASA 5520, with version 8.3, and ASDM 6.3. Currently I have a requirement for users in my internal network (10.10.249.128 / 25) to be able to connect to external IPSec VPN servers.
So I created a network object with 10.10.249.128 / 25, and used dynamic PAT to translate the source ip address to the external internet facing outside interface:
I then added the following rules on the inside-in ACL: However troubleshooting shows that isakmp is passing through the firewall, but esp and ah is not.
For isakmp:
For ESP:Seems like the nat rule is drawing my ESP traffic,
View 1 Replies
View Related
Aug 2, 2011
I've download a login.html into the controller successfully, but when I preview the page there isn't an accept button. Do I need to create the accept button with the html file or is there some place I need to enable on the controller itself. After download the .tar file I reboot the controller but no luck. I also create a java script button redirect but it didn't redirect to where I needed to go. It just stuck on the splash page.
View 3 Replies
View Related
Jan 31, 2012
I'm trying to find a reference for how many IPSEC tunnels the WRVS4400N can passthrough.
View 0 Replies
View Related
Sep 22, 2011
I'm trying to access a machine via pptp through a new WAG320n without any success. PPTP Passthrough is enabled i've opened port 1723 TCP pointing to my machines ip-adress but i can't get the connection working.
View 9 Replies
View Related
Jul 7, 2011
I just bought this router recently found out its a strong good router but i got shocked that there is no PPPOE passthrough option on VPN passthought i am disappointed because this option is soo important to me and i just spent money on nothing, is WAG160N doesnt support PPPOE passthrough ??? and if it does how can i do it .
View 9 Replies
View Related
Sep 22, 2011
I have e3000 but in VPN Passthrough I don't have ( pppoe passthrough ). Just I have is ipsec + pptp + l2tp only. How could I add ppoe passthrough in my e3000.
View 2 Replies
View Related
Mar 19, 2013
Region : UnitedStates
Model : TL-MR3020
Hardware Version : V1
Firmware Version : latest
ISP :
I have problem to get pptp working. I setup pptp VPN server on my home router and configured pptp dialup on my laptop. If my laptop connect to internet directly, I am able to connect to home router via PPTP VPN. However, if I connect TL-MR3020 to internet(wired) and then connect my laptop to TL-MR3020 wirelessly, I can browse internet without problem. The problem is I cannot connect to home router via PPTP VPN any more. I believe the problem is on TL-MR3020.
View 4 Replies
View Related
Jan 17, 2012
I have switch cisco 2960 ,When you boot it displays the message that is unknown for me.
View 4 Replies
View Related
Feb 14, 2012
Any setup passthrough mode of the Motorola NVG510 router ATT makes you use with U-Verse to a CISCO 877 or similar, with a block of public addresses they want to use? It is So frustrating that I have to deal with this NVG510. It is NOT a very business class router... I am assuming that I need to put it into "pass through" mode for the Cisco to be able to manage what happens with my assigned public addresses. If there is another way, let me know!
Here's what I plan to do: I've read the "related to" post above, about putting the NVG510 into pass through mode, and I plan to do this as it discusses. I'll assume that works for now. But it will assign the router's WAN IP Address to the router's "outside" interface, not one of my private IP addresses. On the Cisco side, here is what I would do: vlan1 interface is my "inside" private network. Create vlan2 interface using dhcp to get IP/gateway from the nvg510, or set it up manually, whichever works... This interface will be the "outside" NAT interface. But this interface's address will be the router's WAN address, NOT the first of my 5 public assigned usable addresses...
Here is how it will be setup:
interface FastEthernet0
switchport access vlan 2
[code]...
Then - make it my default NAT interface: ip Nat inside source list 110 interface Vlan2 overload
If I stop there... I assume I could then NAT ports from my different private addresses to the various servers in my office. But the router won't have an interface with that first assigned-to-me public address. The reason I ask is that we have a site-to-site crypto- map defined, and the interface it is defined on determines the IP Address it will communicate from. I wanted this to be my own assigned public address, not the WAN address of the router... Not sure how I would do that though... Same with the default NAT assigned to vlan2 - by default machine in access list 110 will get to the internet with the WAN address of the nvg510, not my private address.
Can I create interface vlan3, somehow linked to vlan2, give it the first private address in my block, and then move the cypto-map to this interface, and also change the default Nat to vlan3 now instead of vlan2? ip nat inside source list 110 interface Vlan3 overload
How would I go about doing such a thing? I am not a Cisco expert, I understand just the basics... This is a bit more complicated than I can figure out. Or maybe it is not possible? Will I have to, for any computer that needs unsolicited traffic through the internet to use one of my assigned public addresses, to setup a one-to-one NAT for that address to that internal address? And everyone else is stuck using the WAN address. If this is the case, it is not right... What were they thinking when they designed this router and forced us to use it as a business class U Verse customer? This should NOT be so difficult/complicated.
View 1 Replies
View Related
Jan 24, 2013
Region : United Kingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP : ADSL24
How to successfully get VPN passthrough working with the W8960N?
I have the W8960N providing internet to local device. I want to setup a second router, TP-Link 1043ND with WW-DRT and PPTP set up to provide a separate access point for PPTP tunnelling to VPN servers outside of the UK. HideMyAss are providing VPN servers I wish to connect to.
I have followed instruction to set up both routers but would like to know if I am missing something.
First router 192.168.1.1 is basically untouched but with ports under NAT added: ports 1723 and 47 for my second router at local IP 192.168.1.111
Second router is set up according to [URL].
I know VPN work via just my first router. I can tunnel through using an Android tablet and connect to any HMA VPN server without changing anything on the 8960N.
View 1 Replies
View Related
Aug 23, 2011
Using a Mac running Mac OS X 10.6.8 with VPN Tracker 6.3.0.Before switching to the WAG320N I had no issues with my IPSEC VPN client. After the switch it consistently fails in Phase 1 negotiation.In the log file of the gateway I only notice: Mon, 2011-08-22 07:47:31 - [Outgoing] UDP Packet - 192.168.1.100:500 --> IP.ADDRESS.VPN.GATEWAY:500.The software itself complains about timeouts while contacting the remote gateway.VPN pass through is enabled, no port forwarding is set up, firewall is disabled.
View 6 Replies
View Related
Jun 4, 2013
upgrade from 7.0.235 to 7.0.240? I can't go any higher right because we are still using WCS. I read the white papers but as far as I can tell there are no new features..
View 3 Replies
View Related
Apr 29, 2010
Does Cisco WLC 5508 runnig code 6.0.196.0 allows you to generate CSR? Or do you have to use OPENSSL like in previous versions?
View 16 Replies
View Related
May 1, 2012
I am trying to SSH into my controller after upgrading to 7.0.103 and I get the username prompt but it seems to be disconnecting as soon as I do. Is there something different about this version of code as opposed to the older ones?
View 1 Replies
View Related
Oct 30, 2012
NCS 1.1.1.24 (PRIME-NCS-VAPL)
5508-50 WLC 7.0.235.3
I had to re-IP this WLC onto another management vlan. Prior to the IP change and code upgrade I removed the WLC from NCS.When attempting to re-add the WLC to NCS, I finally found the it in Configure>Unknown Devices. Now NCS is showing the Device Type as Unknown, and Inventory Status Detail as Unsupported device, and reachable.
View 3 Replies
View Related
Aug 21, 2011
I have a customer with an ACS for Windows version 3.3. I know the ACS is End-of-support, but if I could do Authentication for a WLAN with a Controller 5508 Softwareversion 7.0.116.0 and how?
View 3 Replies
View Related
Sep 25, 2012
Since the SW upgrade to version 7.3.101.0 (wlc 5508) i have the following issue. We have a W LAN with 802.1x (WPA2/AES) secured. Before the update the users need to enter user/ PW every time when they reconnect (W LAN switch off/ on again) to the W LAN. Now the users don`t need to enter user/ PW when they reconnect to the WLAN.
I could not find any setting on wlc to clear this issue.
View 9 Replies
View Related
Aug 22, 2011
Does anyone know if it is possible to use an 5508 WLC running version 7.0.116.0 as a DNS box? Was not able to find anything in the config guide.
View 2 Replies
View Related
Apr 10, 2013
Cisco WLC 5508
Software Version: 7.4.100.0
Windows Server 2008R2
I've got everything setup on the Windows Server 2008 side of things (certificates, radius clients, etc). I added the radius server on the WLC, and configured a new W LAN to use it. Both are on the same sub net. When trying to connect to the W LAN it kept failing. I installed wire shark on the server to monitor the radius traffic, and to my surprise there was no radius traffic showing up on the server. The radius statistics on the WLC are at 0 as well, so it's like the WLC isn't even attempting Radius.
I re verified that the server was enabled on both the security tab and the W LAN itself on the WLC. Rebooted the controller and the server, all to no avail. I used a radius test client, and can successfully send radius commands to the server using that utility. Frustrated, I just kept trying to reconnect on my wireless device, and after about the 15th try, finally I saw radius activity on wire shark. It rejected my access, but at least I saw activity. It also registered radius statistics on the WLC as well.
So now if I keep trying to connect repeatedly, about every dozen or so times the WLC actually will send a radius request to the server.
View 8 Replies
View Related
Mar 26, 2013
I have a main with one WLC 7.0.240.0 and have acquired a HA with 7.3. I have considered whether to put on both WLC version 7.3 or 7.4.:
first, that there are differences between the two versions?
second: As I read, the version 7.4 can make backup of several WLC, this function is already available?
View 7 Replies
View Related
Jan 8, 2013
configured the monitor and exporter on the wcs 5508 running 7.4.100.0 and it is not working.
View 1 Replies
View Related
Apr 4, 2013
I have a WLC5508 with around 70 AP's (LAP1042N) connecting over an MPLS WAN network. WLC and AP's are running 7.4.100
From time to time I have an AP which disassociates from the WLC with the logging beneath. This is a problem with the AP, or is this due to network saturation between the AP and the WLC ?
And if so, should I change the default retransmit values ?
View 1 Replies
View Related
