Cisco WAN :: 1811K9 NAT Configuration Not Working In 891K9

Jul 30, 2012

A new industrial control system uses 891K9's, an existing system uses 1811K9's. We are using (1) 891 per identical machine group  w/NAT to translate to translate identical IP's/ports in each group (LAN side/inside) to unique IP's in another subnet (WAN side/outside) (Port forwarding). At the office I tested an 1811 config. in a new 891 and was able to connect to a piece of the equipment on loan for this test. Communications were good, no issues.
 
Onsite, the 891 is able to establish communications & all is well for about 15 minutes, then comm's fail and I lose comm's. I've done this on many systems with the 1811 but cannot get the 891 comm's to remain on.
 
Attached is the Router config. used. My PLC (outside device) is looking at the Router FE8 WAN address and inside device static IP/logical port in the LAN, through theLAN ports to the machines switch/hub where the devices connect.
 
Is there a config. detail that needs to be in the 891 that the 1811 didn't need or have? I use the blue cable w/Hyperterminal/CLI to copy/paste the config files into the Routers. I use "Write erase", "Reload", "enable" then paste to host in Hyperterminal and the config self loads. No issues with that procedure, logging in to the new Router config, etc.

View 3 Replies


ADVERTISEMENT

Cisco :: Configuration Is Not Working

Apr 11, 2011

why the following configuration is not working? I have two clustered ASAs inline from one another, in front of a 4506-E switch in front of a host I want to access via RDP, like so: My issue at this stage lies with getting the UNTRUST firewall configured. I've tried the following configuration 1) Creating the host.

View 13 Replies View Related

Cisco :: Configuration Management In LMS 4.1 Is Not Working?

Jan 9, 2013

I need to archive the configuration for the devices but it states that SSH fails to authenticate although I have checked the credentials many times.

View 1 Replies View Related

Cisco VPN :: ASA5505 Configuration Not Working

Mar 8, 2011

I would like to configure a cisco ASA5505 IPSEC VPN. I used the wizard and tried to connect to the outside .. does not work .. The network is configured in this manner: - ADSL router with public address and internal address 192.168.2.1 -> firewall interface inside and outside 192.168.2.2 192.168.3.1 (my network is 192.168.3.0). I used a VPN to the pools ranging from 192.168.4.1 to 192.168.4.100.
 
INTERNET ----- ROUTER ------ ASA5505 -------LAN
What should I change? there could be problems between the router and firewall?

View 6 Replies View Related

Cisco WAN :: 861w - Configuration Is Not Working?

Oct 15, 2011

I have bought a 861w to replace my 877w. We switched from telco(ADSL) to Cable due to faster speeds for up and down. My current physical setup is as such. Cable modem is a straight trough with 4 lan port in the back. Al lan ports are configured by the cable company for my assigned public ip’s. (24.x.x.2 through .6  – 255.255.255.x) I also have my assigned gateway as 24.x.x.1

My goal is to setup the new router same as the old one so all interfaces (e0 to e3) use a Vlan1 and Bridge Bvi1 to get the traffic go through e4 which is my WAN port on 861. I am not even concerned abt the wireless because I can’t get this to work. I am attaching the running config on the old 877 and 861 so you all can see what it was and what I am trying to do. As of now I am so confused that my head is spinning……I am able to ping out and ping e4 from outside but I am not able to connect any pc’s or node and connect to net from inside on any of e0 to e3.

View 12 Replies View Related

Cisco VPN :: SDM Configuration Not Working In 1841?

Feb 23, 2013

my problem in configuring a cisco 1841 as VPN server using SDM, everytime i press Lunch Easy VPN Wizard botton, there were no response at all. my IOS is:
 
Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(15)T15, RELEASE SOFTWARE (fc3)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
System image file is "flash:c1841-advipservicesk9-mz.124-15.T15.bin 
 
by the way I took this IOS to other router with the same model(CISCO1841).

View 2 Replies View Related

Cisco Firewall :: SSH In ASA 5520 Not Working Even With All Configuration In It

May 3, 2013

I am having a wierd case, where in i have a 5520 and i am not able to ssh into that firewall. When did a capture on that firewall it shows my connection is getting reset as soon as i try to ssh into the box. Given below is the config for ssh into the firewall.

!
ssh 10.252.253.0 255.255.255.0 inside
ssh 10.114.255.240 255.255.255.255 inside
ssh 169.2.162.75 255.255.255.255 inside

[Code].....

View 3 Replies View Related

Cisco WAN :: Lab Router 2500 Configuration Not Working

Jun 6, 2013

I grew tired of entering my username and password in my 2500 series lab router. So I removed authentication by typing "no username xxxxxx  password xxxxxx".Different than what I expected (removal of authentication), the router still prompted me for my username, it just won't accept anything I type. 
 
I decided to do a password reset, I changed the register to 0x2102 and then typed "i" for Initialize.   It comes back with error "Configuration from version 12.0 message may not be understood correctly."   and then boots to running config with a prompt for username again....right back where I started.
 
why removing authentication by just typing "no username xxxxx password" would lock me out?If I am actually locked out or maybe there is another way to access?

View 4 Replies View Related

Cisco AAA/Identity/Nac :: 2960 Configuration Combination Not Working

Mar 3, 2013

We have a configuration that work fine but one of the combinations it don´t work.  When we connect a guest laptop, the first time work fine. The configuration is when the laptop don´t authenticates with radius, the dhcp server assigned vlan guest and ip guest. The first time was ok. After, We connect a laptop with users authenticates work ok, the radius asigned vlan of users and dhcp server assigned ip users. The problem was when we connect for two time a guest laptop, radius didn´t validate and laptop didn´t negociate ip with dhcp server. In this time, the administrator of dhcp server, tell us that they didn´t see nothing traffic of my mac. and anymore run fine. If Whe change the port of switch , the laptup start working again.

Radius=NPS
Server dhcp: is typical.
 
Our scenario is with a ip cisco phone. the ip phone don´t have the authentication. The administrator of radius tell us that the configuratation is fine and the configuration of dhcp is fine. When we connect only laptop, everything run ok.
 
Configuration Port.
 
interface GigabitEthernet1/0/3
switchport access vlan 202
switchport mode access
[Code]...

View 4 Replies View Related

Internet Stopped Working - No Valid IP Configuration

Oct 15, 2012

I live in a college dorm room, and my internet stopped working about 2 days ago. My roommates don't have this problem. I don't know what kind of details to give you because I know nothing about this stuff.

Here's my ipconfig /all.
Windows IP Configuration
Host Name . . . . . . . . . . . . : silvery-snow
Primary Dns Suffix . . . . . . . :

[Code]......

View 1 Replies View Related

How To Copy / Paste IP Configuration - Internet Stopped Working

Sep 1, 2012

I don't know how to copy / paste the ip config so I ss'd it:(url) internet provider is RCN, I have AVG and Malwarebytes installed, I've tried disabling them both and didn't fix it! Anyways my internet was working fine, until one day it just suddenly stopped working. We have multiple computers hooked up to the network (5) and all work except mine. This same problem happened to my sister's computer, she has almost the same model as mine. We fixed it by switching it to wireless, but I was wondering if there was any way around that. It's a HP Pavilion. The box thingie lights up green and everything. I can access the other computers through the network, it's just the internet that won't work.

View 3 Replies View Related

D-Link DIR-655 :: Stopped Working After Port Forwarding Configuration?

Mar 3, 2011

I was changing the port forwarding configuration when suddenly the router stopped working, and now the "D-Link" light is constantly on, and the power light and the 4 LAN lights are flashing. Nothing worked, resetting, or unplug and plug again in a short time.

I disconnected it for 12 hours, and when I plugged in again, it kinda worked, and the settings where factory defaults, so when I tried to connect it to DSL via PPoE, when ( I believe ) it reboots to accept the changes, it starting flashing again and completely stopped working.

So I waited 12 hours more unplugged, plugged it and it worked, and the setting from 12 hours earlier were still there. But when trying to connect to the DSL it stopped working AGAIN.

Now I don't know what to do. I guess I am going to keep trying connecting with little differences, until something.

I believe it still has warranty but since the is no official service in Uruguay, it isn't economically viable to send it overseas.

I am currently connected directly to the DSL, sharing connection to other computers through a switch and hosting an ad-hoc wireless network, but the performance is terrible and the wireless range is minimal.

View 1 Replies View Related

Cisco Routers :: Working Configuration To Connect IPad VPN-client To RV042

Nov 11, 2010

Any working configuration to connect the iPad VPN-client (IPSEC) to the RV042?

View 16 Replies View Related

Ratio Supposed To Be Between Download / Upload Speed In Normal Working Configuration

Jan 2, 2011

What is the ratio supposed to be between the download speed and the upload speed in a normal working configuation? My webpages are taking forever to load. I used this speedtest... url...

-download speed: 7.427 Mbps
-upload speed: 0.006 Mbps

My provider is cable, Brighthouse, hooked up to their Scientific Atlanta modem and from there it is hooked up to a Belkin Connect N150 wireless router. I am not using the wireless on my laptop but am wired directly to the router. [code]

View 3 Replies View Related

Linksys Wireless Router :: E1200 Stop Working Due To Incorrect Configuration

Feb 14, 2013

I received a Linksys E1200 from a friend who careless tried to upload an incorrect configuration. After that the device became use full. It don't work at all.

View 1 Replies View Related

Cisco Switching/Routing :: Find A Sample Working Configuration Of (HP Rebadged) 3120 Blade Switch?

Jun 13, 2012

Where can I find a sample working configuration of (HP rebadged) 3120 Blade Switch?
 
I have the Cisco 6500 end configured as follows:
 
interface Port-channel1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,300,304,310,320,560-562,600,740,770,950
switchport mode trunk
load-interval 30

[code]....
 
I will be connecting 9/5 and 9/6 to Cisco 3120G (HP rebadged) Blade Switch in c-Class Enclosure tomorrow.It would be nice to have a rough sample configuration of the above 3120G switch.

View 5 Replies View Related

Cisco :: Working Configuration Between Two BR1310s In Root And Non-Root Mode

Jul 18, 2011

Any working configuration between two BR1310's in Root/Non-root mode? The documentation is vary vague and i can't find anything more secure than WEP. Is it possible to use WPA with radius authentication?

View 1 Replies View Related

Cisco Switching/Routing :: 6509 Convert CatOS Configuration To Native IOS Configuration

Jul 17, 2012

I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
 
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.

View 1 Replies View Related

D-Link DIR-655 :: Does Auto Configuration Overrides Manual Configuration

Dec 14, 2012

I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem.  So, out with the paperclip to do the big reset, causing me to lose my configuration.  When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams.  Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP.  I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either.  I tried EVERYTHING.  Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move.  UPnP had always been checked off in the router.  So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?

View 2 Replies View Related

Broadband :: Tools Can't Find Working Off Line Or Working Online

May 9, 2011

XP Home edition, went to tools can't find working off line or working online to make sure off line is not checked so I can get on line DSL Verizon , Wireless router, wireless switch in on, on the cpu

View 1 Replies View Related

Wifi Not Working On Asus Laptop - Lan Working Fine?

Feb 15, 2013

ASUS Notebook G60Vx Series

Windows 7 Home Premium 64-bit

Intel(R) WiFi Link 5100 AGN

A few days ago my internet suddenly stopped working. I plugged in the ethernet cord and everything worked fine. Checking the properties in the device manager showed the device was working properly, I also tried resetting it to make sure it was enabled but it did not work.

Upon troubleshooting, the "Windows Network Diagnostic" said the problems was that the Wireless adapter was not turned on. Using the switch on the front of the laptop as well as the function keys does nothing. Usually a graphic pops up showing if the WiFi is on or off, changinging transparent to show the WiFi is disabled. Now when I turn the switch on it always appears transparent, effectively going from off to off

So I know the computer reads both the function keys and the switch on the front but both methods never actually turns the adapter on. I just finished a system restore and nothing has changed

View 1 Replies View Related

Wifi Isn't Working On Pc But Its Working On Laptop?

Jun 12, 2012

Today, while surfing the web my internet connection on my PC just randomly shuts off. I go check on my laptop and its normal. My WiFi says that I am connected to an Unidentified network with no internet access. So i got frustrated and checked all the forums and nothing seemed to work. So i restored my computer to factory settings and I still got this problem. Does this mean my Wifi Card is bad? Is it a virus? I can see other networks fine but i just cant connect to mine!

View 8 Replies View Related

Cisco :: Atm Pvc Configuration

Feb 6, 2013

Can any explain this topology for me and how it works ? I don't understand the necessity of defining tow PVCs .

View 2 Replies View Related

Cisco WAN :: NAT Configuration On 877-K9?

Feb 6, 2011

I want just want to know on how to add NAT inside and outside ip address.
 
For instance:
 
Original Address = 119.xx.xxx.257 (8138)
Translated Address = 119.xx.xx.28 (8138)
 On the example above, I can access my web application by typing www.wesbite.com:8138
 
The settings above was configured by the previous administrator and unfortunately I dont know how to configure same thing as he did.
  
Now, I made new web application and set it to port 8139, so I should be able to access it by typing the www.wesbite.com:8139
 
In order to make it accessable on the internet, I should make configuration first on the router via NAT, and I dont know how.
 
Also, I tried to edit NAT configuration via Cisco SDM (Secutiry Device Manager)
 
Cisco SDM>Configure>NAT>Edit NAT Configuration
 
I clicked Add button but nothing happens, even clicking Edit and Delete button

View 4 Replies View Related

Cisco :: LMS 4.1 - NTP Configuration

Feb 25, 2013

I have an LMS 4.1 where sys log reports available for all the reachable devices on the network. All the devices were configured with the command "logging host <LMS_IP_address>".
 
The problem is that the report on LMS are shifted 2 hours from the clock displaying on the devices ("show logging" on any device).
 
How can I check the NTP configuration of LMS? Is it supposed to use the NTP configuration of the operating system (Windows Server 2008)?

View 3 Replies View Related

Cisco :: NAT Configuration In Later Version Of The ASA OS

Mar 27, 2011

Just trying to find my way through the new NAT configuration in later version of the ASA OS but having a few issues.

View 7 Replies View Related

Cisco :: How To Set Configuration On Asa5505

Jul 20, 2012

i have the asa5505 with asa8.4.5 and asdm 6.4.2. my asa work like site to site vpn with the other asa5505. i would be love that monitoring status of VPN. i enabled on asa logging, i puted address of smtp server, receipent email, source email, the problem is because my smtp server require authentication, TLS. how set configuration on asa5505?
configuration of logging for send notification on email.

View 3 Replies View Related

Cisco :: IPSEC Over GRE Configuration

Dec 4, 2012

I'm trying to setup an IPSEC tunnel above GRE using the topology in the attached image file.However the traffic between the 2 endpoints: lo0 on R5 (10.0.5.1) and lo0 on R4 is traveling via the GRE tunnel without being encapsulated in IPSEC: I'm using 2 routing protocols:

- OSPF area 0 for the connectivity between R1,R2 and R3
- EIGRP AS 1 for the internal sites connectivity

View 8 Replies View Related

Cisco :: First Hop Redundancy Configuration

Jun 8, 2012

I'm shortly going to move our stuff to a new data centre, where we have two network feeds - so there'll be two lengths of CAT 5 coming into the rack, for "first hop redundancy".I have something similar at our existing DC, but I'm simplifying the equation somewhat at the new DC, and using a simpler configuration that just uses two switches, rather than two switches and two routers. All of the servers will have public IP addresses.Now - the network guy at the new DC has confirmed that a simpler two switch configuration will work.

View 17 Replies View Related

Cisco :: 3550 - Configuration That Needs To Be Set

Sep 27, 2011

Cisco 3550 and when I do a sh int fa0/1 and the status does not show last input or last output. Is a 3550 have a configuration that needs to be set?

View 0 Replies View Related

Cisco :: ASA 8.4 - Getting NAT Configuration Through Router?

Oct 6, 2011

I have a nat configuration to apply on a 8.4. I am a bit confused.On a ASA 7.0 the configuration is as such  static (inside, outside) 10.102.247.0 10.102.247.0 netmask 255.255.255.0Basically, I want a bidirectional nat .. for users to connect to the inside network using the real IP.object network Delta subnet 10.102.247.0 255.255.255.0,object network Delta

View 0 Replies View Related

Cisco WAN :: 891-K9 Dual Wan Configuration Using PFR

Mar 30, 2012

The basic setup Newly installed redundant ISP, thus setting up the 891 with dual WAN Using PFR to load balance between the two. Did initial config through CCP (not express), but I am familiar with the basics of IOS CLI (not used to the new zone based firewall yet, managed aour old Pix for too long, but that is a different subject)
 
I cannot seem to get anything but Gi0 to be accepted as a WAN interface. I go through the entire setup in CCP, test each connection, etc, and it all looks good until I exit out of CCP and go back in. At that point, I get squat out of Fa8. CCP won't let me test the connection, won't let me edit the connection, wont let me delete the connection. The wizard for a new WAN connection becomes available again (Wanting to set up a "second" WAN on Fa7...)
 
Again, I have verified connections to each ISP line independently, either one works just fine on Gi0, neither ever works on Fa8. This is my first real foray into PfR.
 
Building configuration...
 
Current configuration : 21486 bytes

Last configuration change at 18:59:43 UTC Mon Mar 26 2012 by admin
[URL]....

View 4 Replies View Related

Cisco :: LMS 4.2 - Configuration Collection

Apr 22, 2012

After launching config collection job in LMS 4.2 I can't get job results and receive error message - Unable to get results of job execution for device. I've increased the job result wait time using option in Admin > Collection Settings ... , but nothing changed.Here are screenshots of error message and wait settings I used.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved