Cisco WAN :: 1941 - Ethernet Bundling
Apr 19, 2011
We would like to describe our scenario as follows. We hosted our internet gateway at a service provider which is away from our site about 10 km distance. The total internet b/w is 8Mbps. To connect the internet service provider, we have two lastmile connectivity with two different service providers each 4mb as a last mile. Both put together it will be 8Mbps. The lastmile by the service providers are through ethernet.
Our main objective is to utilise both last mile connectivity by bundling or through any other optimum method. There are common perception that the ethernets cannot be bundled. The router model we use is 1941
View 4 Replies
ADVERTISEMENT
Apr 7, 2011
I am using cisco 1941 router in my DC for Internet service. I am going to terminate 2 WAN links each 4 mbps to my Gigabiethernet ports. Is bundling is possible to enjoy full 8 mbps internet to my organisation?
View 5 Replies
View Related
Oct 4, 2011
In the past Ive always used the 1841 router to run these smaller sites.10-20Mbps/ using 1941 with OSPF and using both ethernet interfaces?
View 1 Replies
View Related
Mar 5, 2013
I'm setting up a lot of small remote sites that are only reachable via VHF ethernet radios that operate at 32k. I'm going to be using 2 of these radios shooting to two seperate base station radios to provide diversity. I'm going to have a Cisco 1941 sitting between the two radios and the way I have it configured now is to only use one radio and the second is only sitting there in case the primary fails. I was thinking though that I could load balance them to give a little more throughput. The devices at these sites are really low speed but we like to use snmp to monitor everything that is ethernet so I wanted to give as much bandwidth as I can.
Will load balancing work in this situation? What would the basic configuration be? This is all internal to our network so there are no ISPs to deal with. We're using C1900-UNIVERSALK9-M IOS will that work or will I need to change that?
View 1 Replies
View Related
Jan 20, 2013
Here's my problem. I'm going to be using Cisco 1941 routers at a bunch of remote sites. All of these sites have 2 comm paths out. Some of them have 2 IP/VHF radios and some have 1 IP/VHF radio and a copper link using Patton ethernet extenders. From the VHF radios the data hit our MPLS network back to our HQ and the sites with copper go directly back to our HQ. Everything ends up at a Cisco 4948 switch. The problem I'm having is that I want the routers at the remote site to use one ethernet port (G0/0) as the primary and the other (G0/1) as the backup interface. I've tried the backup interface command but the problem is that depending on where an outage occurs the ethernet link to either the radio or Patton stays up so it never switches over. We're using OSPF as our routing protocol and I'm sure there's something that can be done with it but I'm not sure what.
View 4 Replies
View Related
Feb 20, 2012
I curently have 2 Data centers connected with a Metro Ethernet Connection. Each Data Center has 6500 with Sup720s. The Metro Ethernet connection is currently conected by a L3 routed interface. I now need to enable VRFs between the locations and want to determine the best way to adjust the Mero. I was considering adjusting the routed interface to use Ethernet sub-interfaces. Each VRF would be given a different subinterface over the Metro Ethernet connection. I have done this on internal LAN connections but am concerned about exteding across data centers over Metro E.
View 1 Replies
View Related
Aug 8, 2012
I am having a problem with my Realtek RTL8168D/8111D PCI-E Gigabit Ethernet NIC. It is not detecting my ethernet cable, and thus leaving me without internet on my desktop, after i updated its driver. The cable is not the problem as I have tested the cable with my laptop. I tried rolling back drivers, doing system restore and removing drivers with driversweeper and letting windows install the drivers again. However, none of these worked for me. I doubt the NIC is faulty as it was working before i updated the drivers. I am using windows 7 home premium 64-bit.
View 9 Replies
View Related
Dec 26, 2011
I've had trouble connecting to my own internet and have no wireless. I'm using my neighbor's wireless and it's really slowing her's down. I've tried restarting my laptop (it usually works) and then reinstalled the device under "device manager". It's not the cord, I've checked with my neighbor's laptop and it works fine.I use a Sony Vaio VGN-NS140E with Windows Vista SP2.
------------------------------------------------------------------------
{ipconfig /all} This is while I only have an ethernet plugged in and no wifi connection.
Windows IP Configuration
Host Name . . . . . . . . . . . . : FairyHo
[code]....
View 7 Replies
View Related
Feb 22, 2012
I have a Cisco 1941 which has several Cisco VPN clients connecting to it which all works fine. The details of the LAN and VPN clients are as below:
Cisco 1941 LAN : 172.16.1.0 255.255.255.0
VPN Clients : 192.168.5.0 255.255.255.0
As mentioned this works fine but I'm about to setup a point to point VPN with from the above Cisco to another site which isn't controlled by myself and the remote side of this point to point VPN will only allow connections from the "172.16.1.0" subnet to communicate with it.
The issue I have is that the Cisco VPN clients also need to communicate with the remote side of this point to point VPN but they are obviously coming from the "192.168.5.0" subnet. Is this possible and where to start with this that would be fantastic.
View 3 Replies
View Related
Feb 18, 2011
I got 2 DC Cisco MWR 1941 and 3600, I do not know the reason why when I set up IP NAT to 1941 does not work but if I do it in the 3600 if it works.
View 13 Replies
View Related
Jun 11, 2012
I just got a new Xbox today, and use the integrated WiFi card. I was lagging like Crysis 2 on a 6800 GT (forget it). I just got a CAT .5 cable, and plugged it into modem/xbox and IDK... it works, I'm online, but basically my question is:Does ethernet connections have less ping (better) than wireless connections? This is with the Xbox 360 Slim. I know it improves upload, and download, but what about ping?
View 2 Replies
View Related
Apr 30, 2011
I have a Dell XPS M1530 with Vista 32 bit. When i plug in a cable i get nothing, no error, and the comp does not recognize that a cable has been plugged in. I think that this started after my Hard drive failed and Dell replaced it but i'm not positive. No errors (? or !) in Device Manager and I can't find the Marvell 88E80XX 10/100 Ethernet Controller in device manager. I have attempted to Reinstall the drivers. The wireless is still working. I have one Light to the right of the port that is on all the time solid but no flashing with the cable in or out.
View 14 Replies
View Related
Sep 5, 2012
I have a problem with my routers (cisco 1941)I'm running a DMVPN network (Hub and spoke)All the hubs are connected to the 2 hubs. With 4 tunnels. (each hub has 2 interfaces to the spokes. the spokes only have one interface to the hubs, so I splitted them and so I now have 4 dmvpn tunnels). one of the interfaces on a hub malfuntioned and because of that the customers had problems with logging in and sending packets. I made this kind of structure because of when one of the tunnels failed the spoke could use the 3 others... BUT, what happened here was that the spoke still tried to use all 4 of the tunnels and because of that I had 25% package loss!So this didn't work. Now I read about IP SLA, but I was wondering of this could work? (I cannot test it on spare routers, and I don't want to implement it and risking a total network failure...) and how to configure it. Should I make 4 different sla processes which I should all 4 track? And when I make the ip routes, how should I make or configure it so that 1 of the tunnels/interfaces fails that the spoke would addapt the routes?
View 1 Replies
View Related
Apr 11, 2012
I'm trying to get two Cisco 1941 routers with HWIC-1T and HWIC-3G-HSPA interfaces to use the 3G interfaces if the frame is down (as it is right now).In the lab, I was not able to get these to use the 3G interfaces as a backup (i.e. backup interface cell 0/1/0) and I've not been able to workout the correct incantation for static routing either.
kununurra#show ip int br d1
Interface IP-Address OK? Method Status Protocol
Dialer1 172.31.2.94 YES IPCP up up
[Code]....
View 4 Replies
View Related
Mar 20, 2011
I have been breaking my head over a problem with my new 1941W ISR since about two weeks now.When I restart the router, the service-module wlan-ap0 is not working.After a restart of the router, when I ask a service-module wlan-ap2 status, I get:Service Module is Cisco wlan-ap0Service Module supports session via TTY line 67Service Module is waiting for registration messageService Module reset on error is disabledService Module heartbeat-reset is enabledService Module is in fail openService Module status is not available
After a while it changes to Service Module is failed.If I restart the module with service-module wlan-ap2 reset, it works. Is this a technical error?
View 4 Replies
View Related
Jul 1, 2012
We bought a CISCO1941 K9 router. To enabled IPSec feature, I need the PAK to active IPSec on 1941. Where I can buy a valid PAK? Could it be done via on-line support?
View 5 Replies
View Related
Mar 23, 2011
I have got a Cisco 1941 router and would like to activate my SSL VPN license on it. How do i go about it?
View 6 Replies
View Related
Jan 31, 2012
What is the processor available in cisco 1941 router? is it RISC?
View 4 Replies
View Related
Mar 22, 2011
How do i configure SSL VPN on a Cisco 1941 router? I would very much want a howto guide that does step by step. I have not found one my self so far.
View 1 Replies
View Related
Jan 26, 2012
On our Cisco 1941, we have 2 gigabit ethernet ports and a 4 port fast ethernet switch EHWIC card configured as follows:
GigabitEthernet0/0 131.x.x.81 255.255.255.248 - internal
GigabitEthernet0/1 131.y.y.234 255.255.255.252 - WAN
Vlan2 192.168.0.249 255.255.255.0 - LAN2, NAT inside
[Code]....
I have tested using some UDP packet sending/receiving software (which works through another router), and the packets just aren't getting through. Likewise trying to telnet into the external IP on port 80 doesn't get through to the destination server.
It feels like the route doesn't exist between the Vlan 100 and Vlan 2 when it's coming in, or maybe there's an ACL needed for the incoming traffic?
View 4 Replies
View Related
Aug 15, 2012
We have a Cisco 1941 Router with two single HWIC cards supporting two T1 lines 3Mbps total bandwidth. We have a distance learning lab that takes atleast 2mb connection when in use so it realy kills our bandwidth. I was looking to possible add a thrid T1.
My question: Can I just buy a double wide HWIC card and replace the single port one. Would this require re-configuration or it's simply plug n play?
What other options can I try for more bandwidth instead of adding thrid T1.
View 4 Replies
View Related
Jan 28, 2013
I've got some 1941 ciscos set on every branch.We have native L2 between this offices and I want to use external ip addresses on gig 0� interfaces anfdf local ip addresses on lo 0 interfaces, and use lo 0 for vpn connections.
I do:
int gig 0/0
ip add 192.168.181.14 255.255.255.0
ip nat outside
I can ping it from local network behind giga 0/1 but i can't ping it fro outside, how can i do this?
View 2 Replies
View Related
Mar 19, 2012
I have recently gotten a cisco 1941 router running version 15.1(3)T, and am trying to configure the router as a PPPoE server for access via a vlan on one of the gigabit ethernet ports.I currently have a cisco 2620 router (version 11.3(2)XA4) with the following relevant configurations:
vpdn enable
vpdn multihop
vpdn domain-delimiter @ suffix
!
vpdn-group pppoe
[code]....
I am trying to duplicate this (all but IP addresses) on the new router, but there are some options that do not seem to exist in this particular software/hardware combination. Specifically,
vpdn-group pppoe
accept-dialin
protocol pppoe
does not accept "pppoe" as a protocol, only allowing l2tp. What has changed, and what the proper configuration is.
View 1 Replies
View Related
Mar 28, 2011
We purchased this router with the cisco IOS software installed. I've installed the Vista driver on my win 7 box. I believe that should work. I installed Putty to termainl in and I'm using a USB connection. I cannot even log into the router. I thought I was going to see some kind of setup wizard using the CISCO software so I would use a GUI and get things moving. I've got loads of reference material with command etc. but I just can't connect to the router to make it happen.
View 3 Replies
View Related
Aug 7, 2012
I currently purchased, Cisco 1941/K9 with 2 onboard GE, 2 EHWIC slots, 1 ISM slot, 256MB CF default, 512MB DRAM default, IP Base.
Questions
1. With IP Base License, will I be able to run Frame Relay? I really need reference on what works and what doesn't between these different technology package licenses ? Actually frame relay is running on it right now, hope it doesn't suddenly stop after 60 days...
2. As I understand in order to run MPLS, I will need to upgrade to Data License "SL-19-DATA-K9". Since, I already have a Cisco 1941 to upgrade it, I need to order a spare license / paper PAK?
3. Does the IP Base License support site to site IPSEC VPN or do I need to purchase a security license "SL-19-SEC-K9"
4. Can I have both security and data license activated on the same device ?
5. If I do activate security or data license will I be able to use the IP Base features at the same time?
6. If I purchase a new Cisco 1941 with Data or Security License do I need to purchase the IP Base License then upgrade the license?
7. Is the 1941 suited for voice application routing ?
View 4 Replies
View Related
Jul 31, 2011
I have a site to site vpn between a Cisco 1941 Router and a Watch guard XTM22 Router. The tunnel is up, and from the side with the Watch guard Router, I have full access to the LAN on the Cisco 1941 side.
However, I cannot access any of the devices on the LAN on the Watch guard side. If you had to guess, which router would you say is causing the problem? I really don't know where to start looking.
View 7 Replies
View Related
Mar 11, 2012
I was wondering about the folling witch i found in a Cisco 1941 running config
View 2 Replies
View Related
Dec 28, 2011
My ISP is going to provide internet with dual path , for auto changover he (isp it admin) is planing for bgp implimentation.
is 1941 is supportable for bgp protocol ? Is it possible to create bandwitdh rate limit based on ip address on access list (be cause we are getting some 10 Ip address from isp , out of 10 ip address , 3 ip addres has to go 3 diffrent departments) , i want restrict theese 3 ip address with 1 mb traffic as 1:1.
View 1 Replies
View Related
Feb 1, 2012
I am trying to configure TZO DDNS on my 1941. The DDNS lines in the configuration file were provided one year ago by TZO support for a 1811W router, which was working befor i migrated to the 1941. I have attached a config file and a debug file. The unusual part of the debug file is session id 0x95. I thnk this is the format the router would use if it had been configured using CCP. I had tried CCP initially but it didnt work, so I deleted it from the configuration and used CLI instead. Session ID 0x96 is the call the router is making using the CLI configuration, as seen in the attached config file.
I am not sure where the problem is here. it appears to be logging on to TZO. It also appears that the router name is being added to the logon ID in session 0x95...ie instead of myname.net the router is sending cisco1941.myname.net ---not sure if this is relevant or not. It also appears that the update happens? At least that'w what I can garner from the log file.
View 1 Replies
View Related
Jun 2, 2012
I apply extended ACL on my router cisco 1941, but it didn't work. So I tried to apply standard ACL, it's work. I'm not sure about my cisco 1941 IOS is support extended ACL. My cisco IOS is
Cisco CISCO1941/K9
c1900-universalk9-mz.SPA.151-4.M1.bin
-----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security None None None
data None None None
[code].....
Is it IOS bug or limit feature on hardware.
View 20 Replies
View Related
Jan 17, 2013
I need to unlock IPSec to my 1941 router but I'm not sure which license(s) to purchase.
View 1 Replies
View Related
May 24, 2012
Suggest some commands to stop downloding from internet on CISCO1941/K9.
View 0 Replies
View Related
Jul 30, 2010
The problem I have run into is that I am not getting any connectivity between my two gigabit ports on the 1941. I have ge0/0 setup as my internal network and is running dhcp, ge0/1 is the connection to the modem. I can't figure out how to configure the connections so my internal traffic on ge0/0 routes out through ge0/1.
Here is my config:
Using 4312 out of 262136 bytes
!
[Code].....
View 8 Replies
View Related
