Cisco WAN :: 2901 VWIC Card Installation
Aug 1, 2011
I added a VWIC2 1MFT-T1/E1 card to my 2901 router. There were two in it already, and I need to add a 3rd circuit. After installing the card, the boot process sees the new card, but once it is completely booted, the new card is nowhere to be found. I've swapped cards around to no avail. The new card works fine in one of the slots that had the existing cards in it.
From the boot sequence, I can see:
Smart Init is enabledsmart init is sizing iomem TYPE MEMORY_REQ HWIC Slot 0 0x00200000 HWIC Slot 1 0x00200000 HWIC Slot 2 0x00200000 <-- New card - same when I had it in Slot 3 Onboard devices & buffer pools 0x0228F000 ----------------------------------------------
[Code]...
View 2 Replies
ADVERTISEMENT
May 3, 2011
I had to dig this stuff out of storage and cobble together a router on short notice. I installed this WIC into a 2821 and I can see it when I do a show ver.
Cisco 2821 (revision 53.51) with 249856K/12288K bytes of memory.Processor board ID FTX1006C0P32 Gigabit Ethernet interfaces2 Channelized T1/PRI ports <-----------------------------1 Virtual Private Network (VPN) ModuleDRAM configuration is 64 bits wide with parity enabled.239K bytes of non-volatile configuration memory.125440K bytes of ATA CompactFlash (Read/Write)
When I do a sho run I see this:
controller T1 0/0/0 framing esf linecode b8zs!controller T1 0/0/1 framing esf linecode b8zs
How do I configure IP interfaces on it though? It doesn't seem to show up as Serial ports on a sho int. Am I doing something wrong?
View 2 Replies
View Related
Dec 18, 2012
I was looking an HWIC card for CISCO2901-SEC/K9. We have one internet connection (ADSL) current.Now we want to backup internet connection from cable service provider. I will implement IPSec on this HWIC.
What HWIC cards can I choose for this router?
View 6 Replies
View Related
Jun 2, 2012
Recently I dual-booted my PC from Windows XP(On which the LAN card was working and i was able to access the internet) to Windows 7.Then i formated the drive on which WinXP was installed. Sometime later i noticed that the LAN card (Atheros A8151 PCI-E Ethernet Controller) was not working i went into the adapter settings in network control in the control panel and there was no adapter. i checked the device manager and there was no option called NETWORK ADAPTERS.
View 14 Replies
View Related
Feb 2, 2010
i have a dell inspiron 1440.i am unable to install lan card real tek driver so that i can connect to local area network internet cable,after uploading driver in network places i see
LOCAL AREA NETWORK bluE tooth lan access server will this connect to local cable? THE lan driver real tek after installation says that shut down and plug realtek PCI-E card to complete installation?what do i do?
View 1 Replies
View Related
Feb 25, 2013
I have the Mts Mbrowse ZTE AC 8720 data card. it has problem in installing in windows 8 but it works properly in window 7. It has an error fail to install access serial port 0. i didn't understand the error.
View 1 Replies
View Related
Jan 13, 2013
I have checked and re-checked before buying and this card is evidently supported on the 1841 for 'data mode only' which is all I need. I have 3 T1s in Multilink mode and I want to use 2 of these cards (and 3 of the 4 ports) to support it. The problem is that even though SH INVENTORY finds the card, I can't issue the "card type" command to indicate I am using it with a T1 - I get this:
R3(config)#card type t1 1 0
^
% Invalid input detected at '^' marker.
So I tried to issue the "controller T1" command and it does not recognize the slot as containing a T1 card (which makes sense since the "card" command did not work).
I found numerous references to this card being supported in Cisco docs with a minimum OS around 12.2(8) - it varies based on the chassis. I can't find the explicit OS required for the 1841 which is a concern but I am using 12.4(13r)T. SH VERSION finds "2 Channelized T1/PRI ports" which is the MFT card.
I need to get Serial interfaces configured on these cards.
View 5 Replies
View Related
Apr 11, 2005
I have a 2811 that I'm in the process of turning-up to support a 4xT1 using VWIC-2MFT-T1's. The question is how to "correctly" set clocking on the MFT's.
As is typical of the 2MFT's, as soon as a 2nd T-1 on a VWIC-2MFT comes up, I start taking "Slip Sec"s on the 2nd T-1. I have tried different clock source combinations, including "clock source line primary", various "network-clock-participate" (or not) combinations, and about a dozen other stab-in-the-dark configurations. Before I started playing with it, the slips were consistently every 9 seconds. After playing with it, I got them to every 18 seconds. But there shouldn't be ANY. So the question is what SHOULD the correct timing configuration be on that platform?
The VWIC-2MFT-T1's are in slots 1 and 3, so the controllers involved are 0/1/0, 0/1/1, 0/3/0 and 0/3/1.
View 9 Replies
View Related
Sep 13, 2012
We have installed a VWIC-2MFT-T1 interface card into our 1841 router and the interface doesn't show up in CP. # we only need it for data. #
ROM version 12.4(13r)T, RELEASE SOFTWARE
All indications from my research show that this version should support this card, for data only.
why I can't see this card when I show interfaces?
View 5 Replies
View Related
Nov 9, 2011
What ISO do I need to purchase to get Cisco IOS Firewall on a Cisco 2901 - is it just IP Base or do I need one of the Security IOSs?
View 1 Replies
View Related
May 24, 2011
I have a 1-Port 3rd Gen Multiflex Trunk Voice/WAN Int. Card - T1/E1 in a 2901 that I want to configure for data only (T1 connection to the Internet)I don't see any options in the IOS for using this thing as a serial interface (data), only options for configuring PRI/ISDN.
View 5 Replies
View Related
May 25, 2011
The license has been installed onto the router. Here is the relevant out from the show license all:
License Store: Primary License StorageStoreIndex: 0 Feature: ipbasek9 Version: 1.0 License Type: Permanent License State: Active, In Use License Count: Non-Counted License Priority: MediumStoreIndex: 1 Feature: WAAS_Express Version: 1.0 License Type: Permanent License State: Active, Not in Use License Count: Non-Counted License Priority: Medium
WAAS license as it says that this is not in use, WAAS under the interface is not possible.
View 1 Replies
View Related
Feb 23, 2011
I am trying to come up with a config for implementing QoS over a 512 kbps WAN link that will traverse voice and data traffic for now. I am using a Cisco 2901 router with 15.1(3)T IOS on it. my config is below
class-map match-any DATA-PRIORITY match protocol citrix match protocol sshclass-map match-any VOICE-CONTROL match protocol skinny match protocol mgcp match protocol h323class-map match-any VOICE match protocol rtp audio class-map match-any ANY match any [ code]...
THE ISSUE IS : when i add in the service-policy output WAN- QOS- POLICY command , i get the error " insufficient bandwidth 256kbps for bandwidth guarantee (180)". if i take out the " bandwidth 512 " command out then i get no issues adding the above command on interface g0/1
View 3 Replies
View Related
Jun 9, 2013
I have a Cisco ASA and a 2901 Cisco Router connected via site-to-site VPN. The ASA can ping over the VPN to computers behind the router, but the router can not always ping to computers in the ASA network. When i ping from a computer in the IOS router's 10.100.36.0 network the requests times out most the time; although every few minutes, i will get about 10 pings back, then stops working again.
I uploaded their two configurations.
The ASAs public IP is 20.20.20.5 and local (inside) network of 10.101.36.0/24
The IOS routers public IP is 20.20.20.10
There are many internal networks, but 10.100.36.0/24 is the one with issues.
View 1 Replies
View Related
Nov 6, 2012
I try to make a gre tunnel with 2 cisco routers 2901, ping responds between tunnel ip's ends, but I don't have pings from the pc's inside the networks. [code]
View 7 Replies
View Related
Feb 7, 2012
How do I disable fragmentation on a 2901 router? I want it to simply drop packets oversized packets.In my lab, I am trying to test various MTU issues. I'm trying to use a 2901 router to simulate the WAN equipment that my WAN provider would deploy in production. In production i'm expecting the WAN to only support an MTU of 1320 with no fragmentation at all.
View 2 Replies
View Related
Jan 1, 2012
Physical devices are a Cisco 2901 (CISCO2901/K9) with GE0/0 configured as 192.168.1.1
Connected through a D-Link DGS-1210-24 configured as 192.168.1.202
Running on a domain with an HP domain server as 192.168.1.2
The 2901 was an EHWIC (VA-DSL-A oPoTS) on EHWIC 0/0/0
GE 0/0 on the 2901 is physically connected to the DGS-1210 which is physically connected to the server.
VDSL 0/0/0 is physically connected to the DSL jack.
So far the configuration reports all is connected, and I can ping the gateway of our ISP (using CLI or Cisco CP); however the server reports no internet connection and no workstations can access the 'net.
Once connected; I'd also like to allow ports through for use on the network (25, 80, 110, 443, 987, 1723) - but not sure on how to do that just yet!
Our IP is 202.27.19x.19x
Our Gateway is 202.27.217.5
[Code] ......
View 11 Replies
View Related
Jan 27, 2013
I have recently bought cisco 2901 in order to replace it with our 1811W that we have at the moment.When I try to set a failover / backup with rtr; it seems like the function is not valid.Once I select rtr and set the object #, the reachability command is not available.Does that mean this function is not a part from the license package I have?
View 6 Replies
View Related
Oct 4, 2011
I have inherited a setup for a custom application and would like to know if this is the only way this could be set up. How would you do it?The application uses dedicated T1 links to our vendors. There is a Cisco 2901 router in the middle providing the connections. Traffic to specific vendor's IP's are routed to their prospective connections. I have attached a network diagram and a config for the 2901. The way my predecessor(s) set this up, each different vendor uses a different private IP address for the internal links. This seems odd to me. Shouldn't there be a way to have only one subnet on the inside and have the links NAT depending on which route it takes? The servers have persistent routes built in them to send vendor traffic to the associated IP on the router. E.g., traffic to Vendor 1 is routed to 192.168.50.1, the 2901's IP address for the Vendor 1 network. That traffic is then NAT'd to an IP address associated with Vendor 1's link and the 2901 then routes the traffic to the Vendor's end of the link.
I would think that I should be able to revamp this so that internally we're only using one subnet and the traffic could NAT at the link associated with the Vendor. I recently had to add the 3rd vendor connection, and wound up having to duplicate what was done for the other two in order to get it working quickly. I didn't have the time to wrap my head around the best way to revamp the whole thing.
View 3 Replies
View Related
Jul 6, 2012
I recently obtained a 2901 router running 15.2(2)T to replace my old 877 which was running 15.1(4)M1. The 2901 is humming along quite nicely but I have had difficulty configuring one feature which was working fine on the 877. The router needs to be a PPTP client to a hosted VPN service. On the 877, I had it configured like this: [code] I then had a dialer interface to actually set up the connection, and some PBR to control what went over the VPN. All well and good, and it worked fine. But on the 2901, when I try to configure the same thing, there is no such command as "protocol pptp" -- the only option is protocol l2tp.Was PPTP support deprecated somwhere between 15.1 and 15.2, or does the 2901 itself not support it for some reason? Obviously I understand that l2tp is superior to pptp, but at the moment this is my only option.
View 2 Replies
View Related
Mar 17, 2011
I have one router 1841 in which i configured PBR for internet traffic from LAN. I hv two ISPs few server are configured for ISP1 and few for ISP2.I planned to shift my existing setup at 2901 G2 router. when I am configuring the same config on this router so traffic is passing through only from one ISP not from other, if I troubleshoot so I see that the interface which is connected with ISP2 is not getting any input/output packet.
Config is here:
==========
interface FastEthernet0/0
description ****** ISP2 ******
ip address 203.xx.xx.110 255.255.255.248
[Code].......
View 1 Replies
View Related
Nov 5, 2012
I try to make a gre tunnel with 2 cisco routers 2901, ping responds between tunnel ip's ends, but I don't have pings from the pc's inside the networks.
[code]....
View 5 Replies
View Related
Jun 2, 2012
Why I cant correctly use ip sla command. I only have on my 2901 such commands: ip sla ?
key-chain Use MD5 Authentication for IP SLAs Control Messages
responder Enable IP SLAs Responder
server IPPM server configuration
There is my "sh ver"
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
And...What should i do. if i want to create a failover with to WANs
View 2 Replies
View Related
Jul 2, 2012
Where's the ideal place to put the KS? My current setup is 1 KS, 19 GM. The KS sits BEHIND a GM, so all other GMs have to come through one GM to get to KS.Now, I have purchased two dedicated KS routers. I configured one today, and placed it right on my WAN. My WAN is a L2 Ethernet domain, so i just provisioned a switch port in the WAN vlan, and away we go. I copied RSA keys over from the current KS, configured redundancy and the two hooked up, saw each other and it seems to be good to go. For the ACL, I put in an exclustion for my two KS to talk to each other:
deny ip host 192.168.250.40 host 192.168.250.41 (Old IP, New IP)
deny ip host 192.168.250.41 host 192.168.250.40.
I used a test router and pointed it to the new KS, it registered without a hitch... HOWEVER about two hours later (my 7200 second timeout) I lost ALL my branches. My 18 other GM were still pointed to the OLD IP only, they didnt have the second IP configured yet. In a hurry, I quickly disabled the redundancy configuration on the old KS and had to go to each GM and do a 'clear crypto gdoi' on each one to get them to re-register. There were no log messages about not being able to rekey, no log messages about dropped peerings, nothing. Once I did that, everything returned to normal.
The Question I have...
Would having configured the redundant KS caused this problem? Would having one KS behind a GM and the other Coop KS in the WAN make a difference?
Relevant config from existing KS, 2801:
crypto gdoi group GETVPN_GROUP
identity number 1234
server local
rekey retransmit 60 number 2
rekey authentication mypubkey rsa GETVPN_KEYS
[Code]...
View 2 Replies
View Related
Apr 18, 2011
I have a 2901 ISR G2 router, with IOS 15.0.1M3 , this router is not working with static NATing, I have tried to configure this router with one internet link and make few static translations with it. But this configuration is perfectly working with 1841 ISR router.
View 2 Replies
View Related
Jun 9, 2013
We've have a client who had a ordered 2 units of 2901 router to have site to site connectivity. User has bought a leased line of 256kbps from service provider in between two sites, but the issue is the service provider has layed a rj11 cable and there is no rj11 interface on 2901 router it only has two rj45.
View 5 Replies
View Related
Aug 7, 2012
Need to know if I have 2 type of license on my 2901 router: ipbase and uc, will the 2 type of fuctions of this license work at the same time. Another words will i have route and nat functions work with voip having to type of license on my 2901?
View 3 Replies
View Related
Sep 15, 2011
I been working with PPTP server on cisco IOS since a log time ago. Up to release 15.0 seems is just stopped working. I mean external users can log in the pptp but after logged in there no traffic flow. A simple downgrade to 12.4 solves the problem.
But now i have all my infrastructure with ISR2 2901 and all IOS are 15.
View 5 Replies
View Related
Feb 28, 2013
I'm trying to run the ISM-VPN-29 in a 2901 router. Cisco says that the SECK9 and HSECK9 licenses are needed to operate this ISM. However, they also say that the HSECK9 license is not available on the 2901. I'm running the SECK9 license but it's still not working.
This link, table 5 states that the HSECK9 feature license is for 2921 and 2951 only:[URL]This link states that it is a requirement to run the card, and also that the card works on the 2901:[URL]
I am running 15.3(1)T IOS.
View 3 Replies
View Related
Dec 24, 2012
how to install VIC3-2E/M in cisco router 2901 & what precaution should have to be taken.
View 2 Replies
View Related
Jun 10, 2013
I wonder if I can build a NTP Stratum 0 device using a GPS and a Cisco router.Preferred would be a CISCO819 as it has a build in GPS, alternative a CISCO2901 + EHWIC-3G-HSPA+7.
View 1 Replies
View Related
May 12, 2011
We have purchased a 2901 router with permenant licenses for ipbase, security and uc. The router came shipped with c2900-universalk9-mz.SPA.150-1.M3.bin but there are newer releases available. I understand that our licenses will cover us to upgrade to the latest version, c2900-universalk9-mz.SPA.151-4.M.bin, but when I attempt to download I am denied.
How do I go about downloading and upgrading?
View 3 Replies
View Related
Jul 1, 2012
I have a 2901 router and I would like to enable the following feature router mobile. [code] I used c2800nm-advipservicesk9-mz.151-3.T1.bin on a 2811 and this worked without any problem.Is there a possibility that there is some kind of license associated with this feature on a 2901?
View 1 Replies
View Related
