Cisco WAN :: 7200VXR - What Is Exactly Current Throughput Of Device
Jul 10, 2012
I would like to know what is exactly the current throughput of device? How can we calculate if the device is reaching it's throughput?
For example if router 7200VXR has maximum throughput of 520 mbps as per Cisco documents.
How can we measure if the traffic going through the device has reached maximum throughput. Is it the traffic only inbound traffic or the total of invound/outbound on all physical interfaces?
View 3 Replies
ADVERTISEMENT
Jan 26, 2012
I'll have to replace an old WS-C3550-24. Reasons for this: EOL/EOS & we'll need a NAT capable device...
As I understood, the only L3 catalyst that is able to perform NAT is a 6500? Is that correct? If the above is correct, it seems I can only replace the setup by using a router/ASA with a L2 switch. A router with high throughput (+/- 300Mbps) is hard to find, especially as NAT will require CPU resources...
So, my best (affordable price) solution is getting an ASA5520 (450Mbps FW throughput) and a L2 switch?
View 1 Replies
View Related
Aug 9, 2011
I am having trouble with a T1 connection between a cisco 7200VXR and cisco 2600. I have no problem connecting across it, but when I run a download across the link I get a flat 6KB/s. I can't seem to find what is wrong in my configuration that would be causing this.
7200 Router:
#show running
Building configuration...
[Code]....
View 9 Replies
View Related
May 15, 2011
With IPv6 Coming i've been tasked with implementing M-BGP on our 7200VXR running 12.4.
View 5 Replies
View Related
Apr 30, 2012
Is there a keyword that we use under the interface to specify that it is purely management?
We need to assure that the subnet and any node on that subnet is not shared with the default routing table.
how do we set the gateway for the management interface if the node we are sourcing the ssh session from is on a different private subnet?
View 2 Replies
View Related
Feb 25, 2011
I have Cisco 7200vxr doing BGP with 2 directly connected ISP's over ethernet. I am receiving default routes only, and have added a higher weight to my routes learned from my primary ISP. below is my configuration (ip addresses changed of course)
router bgp 100 no synchronization bgp router-id x.x.x.x bgp log-neighbor-changes network 100.100.64.0 mask 255.255.254.0 network 100.100.71.0 network 100.100.78.0 mask 255.255.254.0
neighbor <ISP_A-IP> remote-as 200 neighbor <ISP_A-IP> weight 175 neighbor <ISP_B-IP> remote-as 300 neighbor <ISP_B-IP> weight 150 auto-summary
Advertising my rotues to the primary ISP is fine
7206vxr.rb#sh ip bgp neighbors <ISP_A-IP> advertised-routesBGP table version is 7, local router ID is x.x.x.xStatus codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S StaleOrigin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path*> 100.100.64.0/23 0.0.0.0 0 32768 i*> 100.100.71.0 100.100.64.57 0 32768 i*> 100.100.78.0 0.0.0.0 0 32768 i
Total number of prefixes 3
However, advertisements to the secondary ISP inlcludes the defautl route learned from the primary 7206vxr.rb#sh ip bgp neighbors <ISP_B-IP> advertised-routes BGP table version is 7, local router ID is x.x.x.x Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 0.0.0.0 <ISP_A-IP> *> 100.100.64.0/23 0.0.0.0 0 32768 i*> 100.100.71.0 100.100.64.57 0 32768 i*> 100.100.78.0 0.0.0.0 0 32768 i
Should I not just only be advertising just the networks that i specified in my configuration?
View 3 Replies
View Related
Jun 12, 2012
What is the most current version oF IOS for the following Wireless AP(Aironet 1260)
Product/Model Number: AIR-AP1261N-E-K9
System Software Filename: ap3g1-k9w7-tar.124
View 2 Replies
View Related
Apr 21, 2011
i have a wireless router on which my desktop with XP is connected to wirelessly. I want to add two laptops with windows 7 to the network what do I need to do?
View 1 Replies
View Related
May 2, 2011
I used mixed mesh 1510 and 1520. WLC version is 4.1.192.35M (Mesh).During 2year WLC is no problem. But, recently WLC's current client error.Normally user is 20. But, these day, user is 2500 and normal client is not assoiate.2500 user's status is probing and WLAN profile is unknown. probing client is not automatically disappear.We are locate isolated area. So, wireless user is a few. But, wired user is very many.after WLC reboot, status is OK.
View 2 Replies
View Related
Apr 24, 2012
We're running NCS 1.1.0.58. Since updating to this release from the 1.0 release, the 'Autonomous AP Client Status' and 'Lightweight Client Status' background tasks have been failing with message 'java.lang.NullPointerException'. I believe as a result of this that the 'Current Clients' tab on an AP monitoring screen just reports 'No data available'.
View 2 Replies
View Related
Sep 15, 2012
i have acs v5.3 and i need change current to new password
View 4 Replies
View Related
May 31, 2011
I am thinking of setting up Wake-Up-LAN on my current desktop. The only problem is that I am using a wireless router, and it would be impossible for me to connect it with a cable. Would it be possible for me to use a wireless router? If not, would it be possible for me to use another router, connect it wirelessly to the original router, and connect that one with my desktop?
View 1 Replies
View Related
Apr 24, 2011
my laptop is conneted to the internet everything works,is there a way to show what the 8 characters are?(win xp)......for instance with win 7 there is simply a box to check that says SHOW CHARACTERS
View 5 Replies
View Related
Jul 31, 2011
How can i change the current password of the router?
View 1 Replies
View Related
Jul 22, 2012
I currently have mutiple computers at my place. Once the computer turned on i want the option of which login for the current computer to use, it can login it current computer or the mutiples computer with their content/data all inside. So more like an computer linked. Example, it can only to A or B, A is the current computer data, while B have all the data of the different computer monitor datas, and if i login B it will show that current computer info. And same goes to the B computer, i can login to A or B on the B computer. What makes this very good is that, both the computer logins are sort of connected, for example if im on actual computer A, but logined to computer B and downloaded/changed some files/data on the B login, once i login on computer B to login B, the changes will apply even tho the changes are done in computer A.
View 3 Replies
View Related
Feb 25, 2012
I am trying to upgrade my IOS on a 3550 switch.The switch has 15MB of space total.When I delete the current IOS it leaves only 8MB of space.I need 10MB of space for the new image.Where is this other space being taken up? [code]
View 3 Replies
View Related
Feb 25, 2012
I am trying to upgrade my IOS on a 3550 switch.The switch has 15MB of space total.When I delete the current IOS it leaves only 8MB of space.I need 10MB of space for the new image.Where is this other space being taken up?
View 2 Replies
View Related
Jan 3, 2013
if there is a MIB available for the EHWIC-4G-LTE-V card that would allow me to monitor the current RSSI level?
If I issue the command "show cell 0/1/0 radio" on my Cisco2911 router, I get the following info. I'd like to monitor the "Current RSSI" level in Solarwinds.
Router>show cell 0/1/0 radio
Radio power mode = ON
Current RSSI = -67 dBm
LTE Technology Preference = AUTO
LTE Technology Selected = LTE
View 7 Replies
View Related
Feb 3, 2013
Having just installed a new RV180W router for a customer last week, I am beginning to regret my decision to to go with this model. Issues are as follows:
1. Users connecting via VPN can not browse web or receive email until the disconnect from the VPN.
2. Internal users experiencing very slow web site access and page lockups (speed test shows a good 15MB connection rate)
3. No clear setup for an isolated 'guest' WiFi network.
All of this happened as soon as I replaced the old, stable RV042 with the new RV180W.
View 1 Replies
View Related
Mar 11, 2011
I would like to add a second mifi 2200 to my current contract. (Same phone # & same bill.) That way I can use the second one while I'm on the road & my wife can use the first one at home!
View 2 Replies
View Related
Jan 22, 2012
Will Tomato retain all current settings on my router, or will I have to set it up again from scratch? If from scratch, is there an easier way to ensuring I get all my custom configurations, then from going screen to screen and writing it down? I do periodically back up the config - will Tomato recognize that file?
View 2 Replies
View Related
Oct 13, 2012
regarding Current Time Not Available. I loose internet connecting for hte last 5 weeks, My ISP is good. Bit I have noticed Current Time Not Available and when this happens my internet looses connection. but does state still connected. Using v1.0.03 build 001 Jun 11,2012 can we set manually the time?
View 9 Replies
View Related
Jan 22, 2013
Every time I power down my WLC2504 controller and then back up, the time reverts back to the year 2000.The APs can't join the controller, due to certificate errors, until I reset the clock. This problem just started recently.
View 6 Replies
View Related
Jan 23, 2012
We are close to receiving our new 6513E chassis which I will be running Sup720 cards in. This will be replacing our existing 6509 Sup2 setup in production. What current IOS version should I run on the Sup720 ? I would like to support SSH. The chassis will be populated with a couple of 6724 SFP cards, 2 6704 10 gig cards and a few 6748 line cards.Is there a good intitial config guide ?
View 6 Replies
View Related
Jul 2, 2012
upgrade experience with the 6509E on what IOS version to use. This is a new install, so I want the most current version that supports SSH and works with dual supervisors.
Here is some information:
WS-C5609-E with 983008K/65536K bytes of memory
Current version 12.2(18)SXF17b
Slot 5 Supervisor 720 (Active)
Slot 6 Supervisor 720 (Hot)
Just need a strong base code, no advanced services. Let me know if you any additional information.
View 2 Replies
View Related
Jan 26, 2012
What is the inrush current (AC Input Surge Current) for the Cisco 2851 router? Is it the same as the router 2801?
View 1 Replies
View Related
Jan 18, 2013
I have a Cisco 1921 to replace our current router which is constantly freezing. We have a couple inside servers, one is a web server and application server which needs to be RDP'd to by a couple of clients outside of our network. I cannot get this to work no matter what. I know it's not the server's setup as when I plug the network back into the old router, it works just fine.
All clients have access to the internet, and I can successfully ping/resolve hosts from both the router and a client computer connected. I cannot, however, rdp using neither our public IP, nor our hostname. The hostname does resolve to our ISP assigned IP, but the server cannot be contacted, leading me to belive this is a NAT issue. [code]
View 2 Replies
View Related
Feb 29, 2012
I'm planning to upgrade Cisco ASA 8.2 to an anyconnect essentials and mobile license. Are there any concerns with some users continuing to utilize the cisco vpn IPSEC client while others migrate to the Anyconnect? I just want to make sure when I upgrade the license that there will not be an immediate requirment to have all users switch to Anyconnect immediately.
View 2 Replies
View Related
Jul 18, 2011
I have an AT&T Router that is my gateway to the internet, I have no access to it. I do have the inside ip address of it which is on my private LAN. Just for shiggles we will call it 10.25.240.1 255.255.248.0. That is my gateway address for all of my current devices.I have this shiny new ASA that I want to throw in there to eliminate a proventia and a sidewinder.
The diagram shows two stacks, these are my virtual server clusters with 3560X switches with the vlans configured, and several more switches all configured with vlan 832, connected to a 2950, which is connected to my internal 2600 router. I have 4 Vlans running on 4 different ip ranges, all controlled by the internal router, with only one vlan, let's say 832 that is trunked to the outside world. That vlan has 172.16.1.x 255.255.0.0 network attached to it. All is well, and traffic is routing behind the internal router, but I cannot seem to figure out how to get the traffic to pass thru the ASA. [code]
View 18 Replies
View Related
Jan 3, 2013
We are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies
View Related
Feb 19, 2012
Whenever new clients logs on to the network, the network tends to kick out users already logged on to the network.
View 2 Replies
View Related
Mar 16, 2011
I have DSL, a firewall, patch panel and hubs.The network was already in place by three previous techs. I am not sure how the current setup is done there is no configuration map.The users in office 1 are all connected to a patch panel that then connects to hubs The second office users connect to a hub that then connects to the patch panel then connects to another hub.The internet is connected to a router that will be replaced with a firewall. Should it be setup like thisdsl modem > firewall > patch panel > hubs > Nodes
View 3 Replies
View Related
Aug 22, 2011
how to find the current logged on user on a domain network? I tried nbtscan but it gives me ip address, machine name and mac address. In the server column it gives <server> and in the user name column it give <unknown>.
View 1 Replies
View Related