Cisco WAN :: 866vae Router Doesn't Sync On Regular VDSL50 German Telekom Line
May 15, 2013
my 866vae Router doesn't sync on a regular VDSL50 German Telekom Line (with regular Phone and a dsl splitter, no voip)!?
IOS is 15.1(4)M4. "show controllers vdsl 0" shows, that the modem status toggles:
Modem Status: Handshake
Modem Status: Idle
Modem Status: Unknown
I tried to configure the controller to fix to vdsl2
controller VDSL 0
operating mode vdsl2
but that didn't work. Modem Firmware is
Modem FW Version:23i
Modem PHY Version:B2pvC032b.d23i
IOS image file is c860vae-ipbasek9-mz.151-4.M4.bin
How to proceed next? If i remember correctly, a 886va Router was able to sync on this line...
View 5 Replies
ADVERTISEMENT
Oct 31, 2011
I have a brand new 2911-TS running 2900-universalk9-mz.SPA.151-4.M1. I have connected the async lines to several devices including ASA5510's, 7206V XR and 6506es. I'm experiencing issues where I go to connect to the console port of one of my devices and my access is denied as if the port was already in a session. I clear the line and try again, same response. If I swap that line with a known functioning line I see lines and lines of output as if the device I was trying to connect to was constantly sending data to the console port. I've not had this problem on any of my older Cisco terminal servers. I opened a TAC case and they had me RMA the HWIC module. I cannot find any information about setting some sort of buffer limit or session timeout. I feel this is a configuration, or mis-configuration issue.
View 8 Replies
View Related
May 23, 2013
My new small router 866vae crashes and makes cold reboots every 20-30 minutes. I updated IOS, but it didn't work. The logs show texts like this:
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
-Traceback= 0x808A0980z 0x808A4E90z 0x8089E2B4z 0x808AD350z 0x8086F000z 0x80A3B7A0z 0x80A1D444z
[Code].....
View 1 Replies
View Related
Feb 20, 2011
My new small router 866vae crashes and makes cold reboots every 20-30 minutes. I updated IOS, but it didn't work. The logs show texts like this:
Possible software fault. Upon reccurence,crashinfo, "show tech" and contact Cisco Technical Support. http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000!ip dns serverip nat inside source list 101 interface Dialer0 overload!dialer-list 1 protocol ip permitmac-address-table aging-time 15no cdp run!access-list 23 permit 192.168.1.0 0.0.0.255access-list 101 permit ip 192.168.1.0 0.0.0.255 anyaccess-list 111 permit udp any eq bootps any eq bootpcaccess-list 111 permit tcp any anyaccess-list 111 permit udp any anyaccess-list 111 permit icmp any any echo-replyaccess-list 111 permit icmp any any time-exceededaccess-list 111 permit icmp any any unreachableaccess-list 111 permit icmp any any administratively-prohibitedaccess-list 111 permit icmp any any echoaccess-list 111 permit gre any any!control-plane!!line con 0login localno modem enableline aux 0line vty 0 4access-class 23 inprivilege level 15login localtransport input telnet!scheduler allocate 60000 1000!end
View 10 Replies
View Related
Dec 10, 2011
I am trying to remove a line in a particular access-list configured in a FWSM module using this command "no access-list <acl> line 19 x x x x" but it doesn't work. See below:
FWSM/xxx03(config)# no access-list ?
configure mode commands/options:
alert-interval Specify the alert interval for generating syslog message
106001 which alerts that the system has reached a deny
[code]...
How can I remove a line from the access-list without clearing the entire access-list?
View 3 Replies
View Related
Jul 28, 2011
I use my laptop in Italy most of the time on a wireless router that uses a PPPoE connection. Once I'd got my head around setting that up it works fine.However since I've come back to the UK today I now cannot connect to a regular wireless router, its just not 'seeing it'. I have used this connection in the UK before without problems and the setting are all still saved from my last trip back but it doesnt show up when I try to connect.Is this something to do with the laptop being set up on the PPPoE connection in Italy? Ive deleted the PPPoE connection but that hasnt made a difference
View 3 Replies
View Related
Jul 25, 2012
So I have a WRT160N firmware v3.0 wired connection to my PC, and at least once a day my connection speed drops from 2mbs down to almost dial up speeds at 60kps. Just unplugging the router then plugging it back in seems to fix it every time. I've contacted my service provider and they say there's no issue on their end, and since I don't get this problem when I plug the modem directly to the PC I agree with them. I've done a factory reset and that didn't work. I've gone through the FAQ and can't find anything useful in there.
View 7 Replies
View Related
Aug 26, 2012
I recently updated my WRT54G V3 to frimware 4.21.5 and now get regular wireless connection issues. The wired connection never has any problem (can connect to the router and the internet), but none of the wireless devices can see either.
The problem happens every couple of days, and cycling the power seems to be the only fix. When the problem does occur, the wireless devices don't even see the broadcasted SSID. But cycling the WRT54G's power fixes that.
I've gotten a few suggestions to do a "30-30-30" reset, but can't find exactly what that entails.
View 5 Replies
View Related
Nov 13, 2012
So here's my issue, I just bought this EA4500 so I could use the 5.0 Ghz and get a new 2.4Ghz as my old Netgear would drop the signal on a fairly regular basis. I've set the channel on 2.4 to 1, 20 Mhz Channel, and my neighbors are for the most part using channels 6 and 11 (one guy is using channel 2 at 40Mhz but has a very low signal strength). The signal drops out sometimes as often as every 5 minutes, and now it is doing it on my new router. Here's the kicker, the 2.4 band falls out from my router and some of my neighbor's routers, no new signal seems to come up, but the 5.0 band on the EA4500 is just fine, as is the wired route. Is the 2.4 band just being assaulted at my home and I'll have to deal with it, or is it that my new router, old router, and my neighbor's routers, all suck, and we should all get refunds? Any solutions to troubleshoot this beyond running a netstumbler like software, setting hard channels (including width), and long hours of trial and error? I am running this all from my macbook air, the 5.0Ghz is at 40Mhz, is the only signal, and is on a fixed channel.
View 7 Replies
View Related
Feb 9, 2013
When i connect the Router 2821 through the Consol get error message at regular interval of time %ENVMON-4-FAN_LOW_RPM: Fan 1 service recommended.
View 2 Replies
View Related
Oct 10, 2012
Cisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies
View Related
Feb 16, 2013
I am trying to sync the vizio wireless tv to the router. I need the security code for the ubee router?
View 1 Replies
View Related
Feb 3, 2011
How do I get rid of a 169 ip address on my printer and synch up with router.My HP All In One Serieds 4500 printer has an ip address of 169.254.0 and my router is 192.168.1.0. They need to match in order for me to print wirelessly from my laptop
View 6 Replies
View Related
Feb 16, 2012
I had been using a Linksys Wireless-N Router WRT350N with a Linksys Wireless-N Access Point WAP4400N. The router quit working so I upgraded to a Linksys Wireless-N Router E1550. The problem is, the new router doesn't sync with the old access point. how to setup the Access Point to sync with the new router?
View 1 Replies
View Related
Mar 27, 2012
The reason is i want to know the difference between the leased line and the DSL line. The whole thing behind the confusion is, We plan to have a high speed internet connection in our office. We will don't have a branch office or some thing like that. I preffered to have high speed internet in our office. I found in some website that Lease line will have high speed connectivity(Upto 10Gbps). Can i use the lease line or DSL is enough for our office. Our office contains of 82 user who will use internet.
View 2 Replies
View Related
Sep 9, 2011
What is the difference between DWDM/CWDM and "regular" SFP's? By "regular" I mean Rx and Tx are fixed to specific wavelength. As I have understood, at least Rx of WDM SFP's accepts a range of wavelengths
View 2 Replies
View Related
Feb 19, 2012
have 2 inside networks:
object network INSIDE_10.6
subnet 10.6.0.0 255.255.0.0
object network INSIDE_192.168
subnet 192.168.0.0 255.255.255.0
I grouped these 2 into 1 object-group:
object-group network INSIDE
network-object object INSIDE_10.6
network-object object INSIDE_192.168
Public IP address used for PAT:
object network PAT
host 152.x.x.x
I used the following statement to create Dynamic PAT to public IP address:
object network INSIDE_10.6
nat (any,any) dynamic PAT
object network INSIDE_192.168
nat (any,any) dynamic PAT
Is that correct? Also I'm using one public address to PAT both inside networks. Is there any dvantage of using 2 different ones, so each inside network would be PAT to its own address?
View 1 Replies
View Related
Aug 29, 2011
We have a customer in a country where the local telecom hands out the data E1 link in a G703 interface with two coaxial cables (Tx & Rx) out of a Watson/Schmidt Telecom SHDSL modem.
We need a way to convert the G703 cables and signaling to a regular RJ45 so that we can connect it to the customer firewall which has regular gigabit Ethernet connections. Some have suggested a 1941 with a serial and gigabit cards. We just need a affordable solution for this and the configuration.
View 3 Replies
View Related
Apr 23, 2012
I'm connected to my remote access vpn and am getting the below error, wierd thing i only get this error for ICMP, i can browse data on our network retrieve files etc, but pings fail for some reason
NAT-T is enabled
NAT rules are in place
ICMP is not blocked as can ping elsewhere
Where to being looking as to why only ICMP fails?
View 2 Replies
View Related
Feb 14, 2012
I am configuring a pix 525,i just found out how to activate the subinterface on it so that's good,the box has a primary unit and secondary unit, both are connected from G0 to redundant switches,if i do a show failover, it says it's using the serial based lan failover, which is fine by me,however, do i need to create a single, regular interface.. or a redundant interface?,i.e. if i create a regular subinterface, will failover still apply to this interface?,or for failover to work, do i need to create a redundant interface (with a redundant id)? i do not seem to have the option to create a subinterface when adding a redundant interface.
View 7 Replies
View Related
Oct 16, 2011
i have a Cisco ASA 5520 8.4(1) with a ASA 5520 VPN Plus license
i want to use the management interface as a regular interface (using the no management-only command)is this interface a Gig interface as well ?
View 1 Replies
View Related
Oct 2, 2012
I have a ASA 5510, it does webfilter using regular expression. [URL]
I block ".facebook.com" and it was successfull. But somehow other users is using https to access to FB. how do i filter HTTPS?
View 5 Replies
View Related
Dec 4, 2012
I am having an issue with a specific server that is not reachable from other sub nets. Every other device on the same sub net as the server is reachable via the other sub nets. This server is special because it's NAT'd to an external IP address and has several site-to-site VPN's set up. The firewall is a Cisco ASA 5510.
This is the error I see on the ASA syslog when I try to ping the server from another sub net: 3 Dec 05 2012 10:58:49 10.0.15.101 regular translation creation failed for icmp src inside:10.0.20.8 dst inside:10.0.15.101 (type 0, code 0)
The problem server is on sub net 10.0.20.0/24 and the server IP address is 10.0.20.8. Every device on the 10.0.20.0/24 sub net can hit the server, but devices on other sub nets cannot. For instance, a device on 10.0.15.0/24 cannot reach 10.0.20.8, but can reach other devices on 10.0.20.0/24.
View 1 Replies
View Related
Apr 6, 2012
I am connecting to a Wireless network, through a ZyXel ZyAIR G-4100v2 router. My problem is that I am experiencing very regular packet loss every minute or so. This lasts for around 5-10 seconds on average. I am running XP with the latest service pack. So far, I have checked out;Wireless Zero Config scanning of new stations (disabled that feature).Xirrus network scan (signal is fine and consistent). I am not suffering from any degredation in signal, the problem seems to be that the router is simply not allowing anything through at regular intervals.
View 1 Replies
View Related
Jul 9, 2012
I am trying to secure changes to switches using ACS 5.3 and allowing our technicians to only change the vlan for user ports on the switches. How can I use regular expressions to filter out the 1/1/# ports so that those ports cannot be accessed in config mode? If I allow the following, it allows access to all interfaces with 'gi' in them.
View 1 Replies
View Related
May 29, 2012
We are running WLAN using WPA2-enterprise with AES & IAS server.Mostly we are using AP's 1131 and Cisco WLC 4400.I added on a new location 2 AP 1142G and since the installation I got 3-4 clients having regular disconnections.Basically they are connected immediately to the infrastructure but after a certain amount of time the Win7 icon is having this yellow exclamation sign, and we can see that the connectivity is gone (however the IP settings seems to be still in place, but ping or network browsing is not possible).Stopping the WLAN and starting it again solve immediately the issue (via software or via the notebook switch). Normally the problem doesn't resolve by itself.
I was working beside the laptop having the problem with (my own laptop) during the person got 3 disconnections, mine was running like a charm.We have 85% of the people there working errors free.Checked the 1142 AP for any logs or errors, interfaces status etc...Checked the switches behind, interfaces seems running smoothlyChecked IAS / WLC / WCS for any logs that can indicate an issueCompared WLAN adapter settings of the faulty laptop with mine, discovered some differences and adapted it.Compare the WLAN SSID config in Win7 with mine and adapted the slighty differences found.Used WCS troubleshooting client tool.What I will do again :Verify if the persons having the issue have the same laptop modelVerify settings in the BIOS Verify WLAN adapter driver versionVerify BIOS versionUse WCS troubleshooting client tool on my own laptop at this place.
View 1 Replies
View Related
Apr 2, 2012
I've recently switched to an ASA 5510 on 8.4(3) coming from a Checkpoint NGX platform (let's say fairly quickly and without much warning ). I have a couple questions and they're kind of similar so I'll post them up. I've read docs about regex and creating them both via command line and ASDM, but the examples always seem to include info I don't need or honestly something I don't understand yet (mainly related to defining classinspect maps). If someone could provide a simple example of how to do these in ASDM that would be useful in understanding how regular expressions are properly configured. So here we go.
I know this is basic but I need to make sure I understand this properly - I have a single web server (so this won't be a global policy) where I need to allow access to a specific URL pathfile and that's it. So we'll call it est estfile.doc. Any other access to any other path should be dropped. What's the best way to do this in ASDM (6.4)? I think if I saw a basic example for this I could figure out next few questions but I'll post them as well just in case.
I have another single public web server (again this won't be a global policy) where I'd like to specify blocking file types, like .php, .exe., etc... again a basic example would be great.
Lastly, and this is kind of related, but we have a single office/domain and sometimes we get spam from forged addresses appearing to be from our domain. On Checkpoint I used to use its built-in SMTP security server and could define if it received mail from *@mydomain.com to drop it because we would never receive mail externally from our own domain name. I saw something similar with ESMTP in ASDM and it looks kind of like how you set up the URL access mentioned above. Can I configure this in ASDM as well, and if so how?
View 1 Replies
View Related
Mar 15, 2011
I have site-to-site VPN and IPsec VPN installed on ASA 5505. VPNs work OK except few stranges:I can't ping 192.168.17.104 from remote ip 192.168.17.138 - 305006 192.168.17.138 regular translation creation failed for icmp src OLD-Private:192.168.17.104 dst OLD-Private:192.168.17.138 (type 0, code 0) in the same time I able to ping 192.168.17.104 from my network 192.168.10.0 and can ping from ASA No firewall at 192.168.17.104?How to fix it?
There is my config:
ASA Version 8.2(2)
!hostname ASA5505domain-name domainenable password password encryptedpasswd password encryptednames!interface Vlan1 description INTERNET mac-address 0000.0000.0001 nameif WAN security-level 0 ip address a.a.a.a 255.255.255.248 standby a1.a1.a1.a1 ospf cost 10!interface Vlan2 description OLD-PRIVATE mac-address 0000.0000.0102 nameif OLD-Private security-level 100 ip address 192.168.17.2 255.255.255.0 standby 192.168.17.3 ospf cost 10!interface Vlan6 description MANAGEMENT mac-address 0000.0000.0106 nameif Management security-level 100 ip address 192.168.1.2 255.255.255.0 standby 192.168.1.3 ospf cost 10!interface Vlan100 description LAN Failover Interface!interface Ethernet0/0!interface Ethernet0/1 shutdown!interface Ethernet0/2 shutdown!interface Ethernet0/3 shutdown!interface Ethernet0/4 shutdown!interface
[code]....
View 10 Replies
View Related
Feb 17, 2013
I have deployed a cisco 2504 wireless controller along with four (04) lightweight access points (1041N) in four floors respectivly. The clients connect to the AP which is deployed in the lowest floor have regular timeouts/packet drops. Further this particular ap operates at channel 11 and it has around 11-13 rough access points in the same area and operates in channels such as 1,3,6,9,11. The DCA (dynamic channel allocation) is set to auto in the WLC. Further each ap has maximum of 07 -10 clients at any given time and I have changed this particular ap and checked still the result is same hence there is nothing wrong with the ap.
View 1 Replies
View Related
Sep 18, 2011
my DSL light is blinking at evening around 6:30 evening every day.
View 1 Replies
View Related
May 18, 2012
I tried multiple times to register a username here and no matter what I chose I would only get "An Error Has Occurred" when I submit the info. I've tried this over several days and keep getting the same dead end. So, I went to bugmenot.com and I'm using a generic username that was given there in order to post this. So...there's that...
Starter info... I'm running Hardware Rev A4 of the DIR-655 on the 1.33NA firmware. I never upgraded past that firmware because of all the horror stories I'd read about new firmware here. Up until lately it's been fairly stable. The issues I refer to SEEM to coincide with my recent installation of Apple TV hardware on my wireless network, though I can't confirm. It's never been great with this router, so that could be coincidental. On my network I have a hardwired Mac Mini, wireless Macbook Pro, a hardwired D-Link DNS-321 NAS box, Apple TV, Logitech Revue, iPad, iPod Touch, iPhone and occasionally one each of a Samsung and LG Bluray player (only when they're powered up, which is rarely). I'm also using a wireless repeater in the middle of my house because the DIR-655 doesn't yield a very usable signal in my master bedroom, which is on the opposite side of the house as the router.
With all that being said... I have had terrible issues being able to keep a steady connection wirelessly with this router as of late. Streaming Youtube videos will stop after a few seconds, loading websites will just stop responding all together, and I can't even keep a connection to stream music from my Mac Mini to my phone or AppleTV using Home Sharing in iTunes. I'll get a few seconds of a song and it will just drop out completely. It's been extremely annoying and I'm ready to take a hammer to this router, to be honest.
I've checked my logs and there were all kinds of FIN:ACK, PSH:ACK and SYN:ACK TCP packets that are being blocked. I noticed many of them were coming from Apple IP addresses, so I assume that the AppleTV had a lot to do with those. I actually used the Inbound Filter settings to allow requests from a whole block of Apple IP's, which seems to have settled log items from them down a lot. There are still quite a few that seem to be coming from Google IP addresses (I presume the Logitech Revue since it uses the Google TV interface?), but the Google IP's are too random to go allowing a large block. [code]
I have Advanced DNS disabled. All Traffic Shaping and QoS boxes are checked to enable. Comcast is my cable internet provider. I've noticed that my WAN Connection Up Time is often a fairly low number like the connection to the cable modem drops out frequently.
View 8 Replies
View Related
Jan 31, 2011
i have cisco asa 5510 as firewall, i was trying to block some site using the link provided below
[URL]
and its working fine, but the problem i am having, when i go to download attachment from hotmail its not downloading, from gmail and other mails its
View 13 Replies
View Related
Oct 10, 2011
We have a PIX with 3 interfaces. Inside, Outside,DMZ.
On my DMZ we have some clients that come in and remotely connect back to there office via MSPPTP. I setup the ASA with this to get rid of the error message: regular translation creation failed for protocol 47 src
policy-map global-policy
inspection_default
inspect pptp
Now when the dmz client tries to connect back to there PPTP server I get the following error.
172.31.10.204 0 24.172.85.162 37624 Teardown dynamic GRE translation from dmz:172.31.10.204/0 to outside:24.172.85.162/37624 duration 0:01:30
172.31.10.204 1069 173.188.74.155 1723 Deny TCP (no connection) from 172.31.10.204/1069 to 173.188.74.155/1723 flags PSH ACK on interface dmz
172.31.10.204 173.188.74.155 63767 Teardown GRE connection 8393958 from dmz:172.31.10.204 to outside:173.188.74.155/63767 duration 0:01:08 bytes [ code]...
View 7 Replies
View Related
