I am running two ADSL lines into one C1921 router with 2 ADSLoPOTS cards installed.If I copy the firmware flash file on to the router (adsl_alc_20190.bin) and reboot, only one card shows the new firmware (slot 0).So sh dsl int atm 0/0/0 shows new firmware but sh dsl int atm 0/1/0 shows no change.How do I upgrade them both?
View 2 RepliesI have a 3825 router running 12.4t IOS. I installed DSU/CSU part number HWIC-1DSU-T1 in the router and it does not recognize it. Is this the right card for this router? Is there anything I can look at to determine the issue? I think the router only has 32M RAM. Below is a show hardware. Card is still currently installed.
View 2 Replies View RelatedI am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies View RelatedWe have two cards HWIC-4ESW on router 3845 but we need that the two cards 8 ports conected betwen, if a pc on port 1 can ping a pc conected on port 8 on second card. tis comunication can,t doing a pc on port 1 can,t conected a pc on port 8.
the configuration is the folowing
interface FastEthernet0/0/0
switchport access vlan 100
speed 100
[Code].....
We moved to a different city and trying to access any available network but can't connect. Says no network found. I click diagnose and it says "This computer does not have a wireless network adapter installed and configured"
View 1 Replies View RelatedI have a new d-link wireless N 150 home router DIR-600. I heard of the wan ping which works it connect for online gaming, does or does it not turn on when you install it and is there any other things i can do to improve it? can't connect to League of legends
View 4 Replies View RelatedI tried to add PCI express 1000/100 network card to my Inspiron 620 (ST1000SPEX from StarTech.com). When I power the box, I get no video, either HDMI or VGA. Tried two different cards in all three slots - always the same :-(
How can I add more networking to my box (WiFi is not useful to me) - I need to have at least 2 separate LANs from this box.
I am trying tu update the firnmware of a HWIC 3G-GSM within an 1841. What is the correct firmware?
I have tried
K2_0_7_35 and K1_0_2_18 from [URL]
[Code]......
Within the space of a few days we've had 2 HWIC-3G-HSPA-G cards appear to fail on different router models. In each case the sh cell x/x/x hardware output is empty i.e no firmware version or other data provided and the radio status is off. Attempts to force the interface down using the test ....modem-power-cycle or radio-power off get the same error message that the modem is still in reset. Reloading the router does not clear this so we recently tried to update the firmware using the latest version off CCO. The upgrade using the microcode commands failed with an error of "unable to determine the modem state".
View 3 Replies View RelatedI have 2 WAP4400N access points, each has a different version of the firmware installed and one has options that the other one does not.I have one access point running
If I visit the Cisco site for firmware updates, I see that only one version of firmware is available for this access point... 1.2.14.I realize that Linksys is not Cisco's main area of business, but if you are going to provide downloads for access points you could at least make sure that you have the latest version available.
I have several ASA-5505 units with the SecurityPlus license. These are running older OS versions and I would like to upgrade them. I am wondering if I will lose the SecurityPlus if I upgrade the image to 8.3
View 4 Replies View RelatedDo i need to reset the router after the install all seems good the new firmware installed with no issues.
View 2 Replies View RelatedI have a Dell laptop with a Wireless-G modem built in. Is there any point in getting a USB Wireless-N modem to speed up the overall connection? I don't know if my Cox cable modem service is even fast enough for it to matter.
View 4 Replies View RelatedI have a brand new C1921 with EHWIC-4G-LTE-G using Vodafone to build an internet connection. First I did the setup like shown in the config guides and got the internet connection, but it was unstable.
Then I found some issues with the old LTE- card firmware in the support forum. Following that hint, I did an IOS upgrade to 15.2(4)M3 and the LTE- card update to Modem Firmware Version = SWI9200X_03.05.19.04. Post-checks after the update were all fine.
After that, I reconfigured the router again meeting the config guides. Establishing the internet connection, I get an IP address on the cellular profile, but it's not bound to the cellular interface.
sh cellular 0/0/0 profile Profile password Encryption level: 7
Profile 1 = ACTIVE*--------PDP Type = IPv4PDP address = 10.25.124.59Access Point Name (APN) =Authentication = None Username:Password: 05 Primary DNS address = 139.7.30.125 Secondary DNS address = 139.7.30.126
[code]......
Before the upgrade the IP- address was bound to the cellular0/0/0 interface and I was able to reach the internet.
Traffic Generator TG connected to R1 via switch SW . One end of the R1 is LAN1 interface and other end is WAN1. LAN1 is connected to switch SW. WAN1 is connected to R2 WAN0 interface..
TG ------------- SW ------------------------------(LAN1) Router R1 (WAN1)------------------------------(WAN0)Router R2
I have to pass traffic to R2 WAN0 interface.
Wen I pass traffic say 5000 from TG, I'm to recieve 5000 at R1 lan1 interface but I'm not to recieve at R2 WAN1 interface and hence not to R2 WAN0 interface.
Config at TG:'
-----------------
Destination IP : R2 WAN interfavce IP
Destination MAC : R1 LAN mac
I'm currently trying to set up a new infrasturcture with PEAP.
So, i've got redundant CA routers (c1921), an ACS server and 1262 AP's. Everything is working fine and as i want it to.Certificates are autoenrolled and so on, but if the CA root certificate expires, how to tell the AP to get the new root CA cert.
The root-certs are made by auto-rollover, and rolled on the CA router, but I got no change to get this root-cert on the AP.Is there a way to get them in an automated way, like rollover or enrollment?
Just recently upgrade our 2 5508 controllers from 6.0.199.0 to 7.0.116.0. Since that upgrade, I have a handful (8 to 10) of wireless laptops that now refuse to associate to any access points. The thing these laptops all have in common is some variation of the Intel Wifi Link AGN cards. I have about 200 other clients out there working just fine.
I've tried everything under the sun that I can think of. Patches, drivers, the whole sh'bang.
Is there a known issue with 7.0.116.0 and these particular cards?
I observed that when I was trying to troubleshoot a field issue using two routers I had in the lab, that one of them (an ancient C3620) did not like the PIMv2 Hello messages sent to it by the newer one (C1921).
The symptom observed with multicast routing is that when a source connected to the C1921 tries to register with an RP running on the C3620, the multicast route stays in the "registering" state forever. But going "the other way" - with the source connected to the C3620 and the RP running on the C1921 worked fine.
what I see in the C1921 when it tried to register a connection to the group 224.0.0.39 (for Auto-RP). Note: The two routers are connected via a GRE tunnel. [code] PIM debugging on the C3620 showed the following when the two exchanged. [code]
I believe that the issue is down to the firmware in the C3620 simply being too old and not understanding the PIM options defined in RFC3973 or the Cisco private PIM option 65004 being sent by the C1921 (though the PIM debug does not make it clear whether it is just the unknown options that are ignored or the whole Hello message)
Is there any global or interface-specific PIM option I can use in the C1921 to "dumb down" the Hello message so that the old C3620 accepts it?
C1921, running version 15.1(4)M2, with licence for "IP base" feature set only.Trying to pass multicast via a PPTP VPN from a Windows XP machine to work around a non multicast-aware WAN link
1. With the IP Base feature set I am able to create a plain PPTP VPN without any encryption; the Windows XP machine can bring it up and unicast data passes through it OK in both directions.
2. But when trying to send multicast, only one-way traffic is observed:i. Windows XP host on far end of PPTP VPN and a local PC both running old Microsoft tool "MPING.EXE", sending and listening for traffic on the groiup 225.100.101.102i. The distant host receives and echoes back the packets received from the local machine + sending its own (confirmed with Wireshark running at the far end)ii. But the local machine directly connected to the C1921 router does not hear any packets from the far end; Wireshark shows only the ones it is sending.
3. Group status ("show ip igmp membership") as far as the C1921 is concerned shows both ends (192.168.50.10 (local end) and 192.168.50.201 (distant end via the PPTP VPN)) joined to the group [code]
4. But "show ip mroute" for that group shows an error; for the source on the far end of the PPTP VPN (having the IP address 192.168.50.201), the source interface is incorrectly shown as GigabitEthernet0/0 (should be Virtual-Access2.1 for that PPTP VPN) and the outgoing interface is shown as Virtual-Access2.1 [code]
5. I have tried adding static mroutes and messing about with parameters for the virtual-template interface for the PPTP VPN, but the problem remains. And if I put another local PC onto a different Ethernet port of the router, the multicast traffic does flow both ways - so the issue is solely with the PPTP VPN.After a week of head-scratching I am getting more and more convinced that it's a bug... but wonder if it is already-known, has a workaround, or a fix in newer firmware?
I need to upgrade WCS firmware. Currently i am running with 7.0.172.0 .
View 1 Replies View RelatedRecently I brought SG 300-28.It came loaded with firmware ver 1.0.0.27.Can I upgrade it to ver 1.1.2.0 directly?
View 2 Replies View RelatedI currently have 3 WAP4410n's (actually, they're WAP4410N-E V02s) that have been really unreliable since I got them - so much so that we've had to cron a restart script on another server which is frankly ridiculous - they've always run firmware version 2.0.2.1.
I've tried updating the firmware to new versions in the past with no success - when I do so, it looks like everything's fine, but when I log back in, the fixed IP address information isn't shown, and the wireless is disabled. I can enable it, but I can't select a channel.
At this point, I have to revert back to the old firmware. I've tried restoring to factory setttings before and after the firmware flash, but this hasn't changed anything.
However, recently I was able to flash firmware 2.0.5.3 onto only one of the routers - it worked fine and all information was displayed and wireless enabled correctly. However on the other two, no matter what I try, the firmware won't upgrade succesfully - it looks like everything's fine, but the fixed IP information isn't shown and wireless/channels are disabled.
I have a Dir-655 A3 with the firmware 1.32NA. I cannot get the new firmware 1.35NA to take. The router seems to go through the motions of the upgrade, but at the end, when I log back on, the firmware still says 1.32NA & all custom settings remain.I have upgraded the firmware on this router before and I know that when its upgraded, the router is basically reset to factory settings. All the settings have been backed up and I am attempting this upgrade via a wired connection.
View 2 Replies View RelatedI have a DIR-655 Rev A4.I followed this forum in the past when there were many problems with firmware upgrades beyon 1.21. Because of this I never upgraded and was told to be satisfied that I can still stay with 1.21 as upgrades caused problems for a number of people.Everything still seems fine with 1.21 except the Shareport utility often does not pickup the printer connection upon booting to Windows Vista. I can always work around this by Disable and then Enable. It will then always find the printer. It is a minor annoyance however.Should I still stay with 1.21 or is upgrading to 1.35 NA recommended ? If I upgrade to 1.35 NA is there a downgrade path back to 1.21 if the upgrade does not work well ?
View 12 Replies View RelatedIt baffles me because the admin console doesn't look like it will browse your computer for a firmware update. Rather, it prefers you to specify a tftp or http server. I don't know how I'd set up my computer to be the http or tftp server and it doesn't really go into detail on what configurations or commands that would need to be used. I've used a tftp client in the past to send a firmware to routers and whatnot but not serve one.
View 1 Replies View RelatedI have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies View RelatedI have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1
View 5 Replies View RelatedWe have 2 ASA 5520s in active/standy. We run IOS 8.2(5)24 and I wondered if I need to upgrade as I see the versions have gone to 8.4 and beyond! We are not getting any issues and I'm aware of the difficult migration from 8.2 to 8.4 etc due to the NAT change.
View 3 Replies View RelatedI´ve a problem with my "old" PIX515e device. I wanted to flash this device to a new firmware level but forgot to disable the "lost enable" password before. So I started to make the firmware upgrade on my device, ended up with "flashfs" is busy and I should start the enabled modus and "copy flash tftp" to activate the new flash version. Unfortunalty I cannot do this because I´ve lost my password. When I´m trying to boot this device up now, it will end with a error message...
Unable to locate boot image configuration
Booting first image in flash
No bootable image in flash. Please download an image from a network server in the monitor mode
Failed to find an image to boot
As mentioned, when I will load a new flash image over monitor mode, i cannot activate that image because of flashfs is busy.The password reset bin files will not work too. I tried that too but this one will recongnize no active installed flash.Is there any way to reanimate my PIX515e? In newer devices there are possibilites to work with changing config register but I´ve found nothing about that for a PIX515e.
I cannot find instructions on how to use the latest 4.0.18 ADSL firmware on an 887 router.
I've downloaded adsl_alc_20190_4.0.018.bin from the website and copied it to flash, but cannot find any instructions on applying the firmware. Tried rebooting but made no difference.
What commands, etc, am I meant to use to make use of this ADSL firmware release ?
We have Sg-300-28 serious switches(SRW-2024 k9-EU) and i want to upgrade switch with latest firmware, any info for latest firmware is used for the same ?
View 6 Replies View RelatedI've just purchased 2 RVS4000. The units, which are V2, have been shipped with firmware 2.0.0.3. It seems this version suffers from multiple vulnerabilities I would like to fix asap. Unfortunately, I was unable to upgrade to 2.0.2.7.
One one of the units, I went through the upgrade process via the admin interface. It seemed to work, though it got tucked at 100% - which is a known issue, as per the release notes - but then, instead of having my unit upgraded as advertised when going back to the home page. It seems I'm stuck in 2.0.0.3. I tried the upgrade a couple of times without any success before posting here.
On top of that, the other unit I have is on another site, far from where I am at the moment. It is also a 2.0.0.3 firmware. I didn't try the upgrade, as I prefer to be on site when doing this type of things, this will be the case next week. This other unit seems to be much more responsive than the one I tried to upgrade without success. On the one I have now with me, I have plenty of freezes every time, it can take up to 5mn for the device to respond to a query. The other one I'm managing remotely does not show these problems. Also, even though the units are the same, the "faulty" one seems to have issues to keep all the settings properly. For example, key lifetimes get always reset to 0 sec, and I have to fill 28800 and 3600 each time I make a change in the configuration. Again, the remote one does not have this issue.
So my questions are :
- Any info on this kind of issues with the RVS4000 ?
- Is it normal 2 units purchased at the same time, which have been shipped with the same firmware, behave differently ?
- Is it possible I have a faulty hardware ?