Cisco WAN :: Planning To Install And Configure VSS 6509 Switches
Mar 4, 2011
I am planning to install and configure VSS (6509) switches. But the customer requires that the First Switch should be the main and the second Switch should act as a backup one. (Disaster Recovery).
Once the Main (Primary switch) DOWN the Secondary one should coming UP.But what I am understand in VSS concept the two switches will act as one Switch. And both of them will be UP in the same time.
Is there any solution to configure the both VSS switch as primary and standby switch to provide HA?
View 4 Replies
ADVERTISEMENT
Sep 18, 2012
I have a fresh piece of 7606-S router, i am planning to install a new IOS ( 15.2.4S or 12.2.33-SRD8 ) SIP-200 / RSP720 moduls ... would ypu plese provides me a configuration guide for installing IOS for 7600 serise router.I have the image on TFTP server.
View 3 Replies
View Related
Nov 14, 2011
our 6509 is configured as NTP master. Our 4948 is configured as NTP client.on each of these switches we have configured a management VRF.The problem is that 4948 can not synchronize its clock with NTP master. Both switches are directly connected.show cdp neighbor on 4948 switch:
6K5 Fas 1 138 R S I WS-C6509- Gig 2/2/43
interface config on 6509:
interface GigabitEthernet2/2/43
description *** Mgmt Switch Externe 1 ***
switchport
switchport access vlan 1900
switchport mode access
wrr-queue cos-map 1 1 1
[code]....
debugs on 6509 do not show any packets received or sent to 4948.
View 2 Replies
View Related
Nov 14, 2011
If I have two stackable switches were only one stackable switch has two uplinks one uplink goes to one core 6509 switch and the other uplink goes to the other 6509 core switch can a Layer 3 etherchannel be used if each uplink go to a different core switch, by the way hsrp is running between both switches and also can you give an example how data will be routed from the stackable switch through the ethernetchannel to one of the core switch accross the WAN to another core switch?
View 1 Replies
View Related
Apr 26, 2013
We have WCS running 7.0.164.3...We had upgraded WLSE to WCS a few years back.
I am planning to upgrade WCS to 7.0.240.0... What is the procedure of upgrading WCS in this case? I am not quite sure about the procedure as our WCS was a WLSE before.
View 3 Replies
View Related
Mar 25, 2012
I have to propose/design a network system. It has 350 computer terminals/workstations out of which 300 of them are divided into two separate networks while the other 50 are to be on another network. So I assume I'd need 3 networks (or LANs) I guess (all connected ofcourse)So far I've inferred it needs a mail server, a file server, a print server, a DHCP server to assign IP addresses (C class and private ones ofcourse) and a web proxy server. Also I thought a fast Ethernet LAN network might be ideal here but I'm not quite sure on that (nor have I ascertained what sort of topology or hardware to use).
View 5 Replies
View Related
Jun 26, 2011
I designing a new network for the company.
-Core layer is Cat6509 with VSS
-FW Lauer: Cisco ASA 5540
-Switches: L2 Cisco 2960
What is the best plan to make this redundant to the Firewalls?
View 1 Replies
View Related
Apr 9, 2012
How to config SVI on Cisco 6509 switches??
View 1 Replies
View Related
Mar 21, 2011
I planning to integrate cisco asa5505 device in runing enviornment for filter ip traffic.Internet ----router----ciscoasa----lan.Ip series is public(25.263.25.0/24) througout of network (no privateIP)now how do I set asa in such case and filter traffic from comming into lan and going out to internet.
View 5 Replies
View Related
Feb 4, 2013
configuring 1142 ap for using centeal dhcp.Now i try to install another 1142 as a repeater for first 1142 point.
Here is root config:
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname 3floor
[code]....
View 1 Replies
View Related
Jul 28, 2012
I am replacing an A3 that's slowing dying with a B1. I understand the Firmware versions are different but I was curious if I can save the config file from the A3 and load it into the B1 ? I don't know if the config file includes the Firmware....
View 2 Replies
View Related
Nov 1, 2011
I have a Cisco 6509 connected (gig3/17) to a Cisco 3560 G switch (Gig 0/28). The 3560 switch Gig 0/26)is connected to a distribution switch on another network. The ip address on my 6500 is 10.120.11.244 255.255.252.0 and the ip address on my 3560 is 10.120.11.211. The ip address given to me by the other network is 10.162.20.10 255.255.255.252. How do I configure the new vlan in this situation and the ip address given to me.
View 4 Replies
View Related
Feb 10, 2013
I need to configure on a cisco catalyst 6509 two VACL. On cisco 6509 there are already two SPAN ports configured, there are problems configuring other two VACL?
These VACLs send traffic to a Traffic Analyzer (SIEM), there are particular configurations to facilitate the operation?
View 1 Replies
View Related
Oct 20, 2011
I am trying to configure the NLB multicast for the Microsoft exchange. The moment I am enabling the NLB my core switch 6509 CPU is reaching 100% and whole network getting down. [code]
I thinking I am putting wrong command. I am not able to see the disable-snooping in 6509 Switch.
View 7 Replies
View Related
Jul 22, 2012
We have two 100 MBPS P2P link from two different ISP and we have terminated both the link on our 6509 switch. Now we want to configure the load balancing between these two disfferent ISP 100 MBPS P2P link.
So, how to go and what all options we can try ? We are thinking for Ether Channel configuration. Need your expert opinions on the same and if etherchannel configuration is the option then what would be the configuration for the same ?
View 4 Replies
View Related
Sep 10, 2012
We are currently designing a complete Layer 3 to the edge solution for our customers. The network design is a combination of a collapsed core (Core to access) as well as a three layer model (Core/Distro/Access) for connectivity to the Data Centre, Internet and Wireless Blocks.
The core of the network contains two 6509E switches interconnected on a Layer 3 Port channel (no VSS). Access Layer switches (3750 Stacks) connect to the core switches over p2p routed links (Collapsed core part of the design). Distribution layer switches provide connectivity to the Data centre, Internet and Wireless Blocks.(three layer model.
All IP addressing is being planned for assignment from the private RFC 1918 address block(10.0.0.0/8) for both Infrastructure and Access layer VLANs for users.
Clarifications required for the following:
[code]...
View 17 Replies
View Related
Oct 1, 2012
I have configured the VSS in two cisco 6509-E series with only one supervisor engine, but if i configured with two supervisor engine. it is going to common mode. One supervisor engine is 3c and 3cxl.
View 2 Replies
View Related
Jan 8, 2012
i have 6509+FWSM(4.0.4) now i wanna use stite to stite and ez vpn in the fwsm (multiple context) multiple context mode in fwsm support ipsec vpn?
View 2 Replies
View Related
Apr 22, 2012
I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies
View Related
Jul 1, 2012
We've just invested in a pair of Sup2Ts to upgrade a Sup720 6509 chassis but I'm unsure exactly how the management port(s), aka the Connectivity Management Processor (CMP), should be configured (and patched) in a dual supervisor system?Is each CMP an independent entity or is the management interface configuration (IP address, gateway, etc) replicated between supervisors?If it's the latter then do both management ports need to be physically connected at the same time?
View 1 Replies
View Related
Nov 3, 2011
I previously put this is the 'Video over IP' discussions group, which is not getting any response.I have a 6509 and need to configure QoS on gig line cards that have 1P3Q8T queue structure. I've already got the mls qos configured, and have the correct class maps built for Voice, Video, and Signalling.(I'm not doing autoqos). I have only four classes; voice, video, signalling, and default (best effort).I need to configure the commands on the individual gig ports for the appropriate bandwidths as shown below:
1. 300 VoIP G711 calls x 100kbs/call = 30mbs of priority queue DSCP = EF (46) CoS = 5
2. 150 Video conference calls x 1.5mbs/call = 225mbs DSCP = CS4 (32) CoS = 4
3. 450 Signalling x 13kps/call = 5.8mbs (round to 6mbs) DSCP = CS3 (24) CoS = 3
4. Default class is not marked DSCP & CoS = 0
View 1 Replies
View Related
Jul 19, 2011
Our 6509 has seen better days and we know it's past time to replace it... Question is - go with similar or just use multiple 48 port switches? Then we have old Cisco 2800s in our 9 IDFs that would need updated as well.
We have a mixed environment with about 300 active clients along with about 15 servers and an EMC AX4 over 4GB fibre brocades for backup.
View 19 Replies
View Related
Jan 3, 2012
I have downloaded the ros file, but can't find how to apply it. I know this information must be out there, but can't find it.
View 2 Replies
View Related
Feb 15, 2011
I've upgraded a 6509 switches wich are running in VSS, from IOS 12.2 (33)SHI1 to 12.2 (33)SHI5. After that I'm facing the folowing log messages periodically. [code] I know that this is a diagnostic result from TestUnusedPortLoopback feature. But this interface is disabled (shutdown).
View 5 Replies
View Related
Jan 8, 2012
I want to setup HSRP between three 6509 switches with a single virtual ip for all the three switches.
know if its possible and share any site or config.
View 1 Replies
View Related
Nov 19, 2012
I have 2 6509 switches configured with VSS.As per advised my managment I have to enable SSH but it is not available existing IOS which is "s72033-ipbase-z.122-33.SXI3.bin". SSH available in "s72033-ipbasek9-mz.122-33.SXI10".
upgrade the IOS with VSS configured switches.
View 9 Replies
View Related
Feb 12, 2012
I need the ssid or network name to install a printer, and apparently you can find it on the router's setup page. I have a Sagem@Fast 800 E3 - where do I find the setup page?
View 1 Replies
View Related
Jun 2, 2012
we are using cisco 6509 series switches as core switches. and Cisco 4510,4507 series switches as edge switches. all the vlans are created at core switches and propogating to edge switches through VTP. we are using OSPF as routing protocol at core switch for internal routing. till now we are using 4510,4507 switches as layer 2 switches. Since, 4510 & 4507 switches are hign end swithces i want use them as layer 3 switches instead of layer 2.if i change these switches from layer 2 to layer 3 does it make any impact on our network or better to keep them as layer 2 switches.if i change these switches to layer 3 is there any advantage i will have.
View 3 Replies
View Related
Dec 1, 2012
On our backbone (Cisco 6509) we have the following config.
spanning-tree mode rapid-pvst
spanning-tree extend system-id
spanning-tree vlan 1-200 priority 24576
1. is rapid-pvst the best spanning tree protocol to use? on some switches we have pvst (not rapid)
2. do all switches in the LAN need to use the same protocol?
3. does line 3 :priority 24576 mean that someone set tis switch as root manually? how can one further enforce the backbone as root (so noone adds a old switch with lower root id)
View 6 Replies
View Related
Apr 11, 2013
I am trying to test (if possible) the idea of having 2 6509-E switches connected directly to each other while using VRF-lite (Sup 2T). The idea is to have 3-4 separate networks. For example Net-A, Net-B,Net-C, Net-D. There is no PE router*, just these two switches. Also, there sin't any other access layer switches. All users connect directly to the 6509-E's via switch 48 port switch blades.
Net-A and Net-B on separate VRF's, but able to talk to each other. Net-C and Net-D* on separate VRF's without being able to talk to any other. Net-D* will have a PE since it comes from an external network. This is something I would like to test in a lab environment, but I am not familiar with VRF's.
View 1 Replies
View Related
Apr 21, 2013
In the next couple weekends I'm planning to add 2 CISCO UCS 6248UP Interconnects to 6509 Core Switches via 10G links.
Is there any impact anticipated? It's a production environment and no loss of up-time is acceptable.
View 1 Replies
View Related
Jan 24, 2013
I am trying to understand what load balancing method is used on a port channel on a Nexus switch . I have a server connected by a VPC to two Nexus switches. The nexus switches are only acting as layer 2 switches. I have a 6509 connected via a upstream link that does all of the routing for my VLANS. If have a server connected to the Nexus switches and it talks to a server on my 6509 what load balancing happens on the Nexus going across VPC 27 which is a layer 2 trunk going up to my 6509. Is it done on layer 2 or layer 3 flows?
My Nexus shows the default load balancing configurations
Port Channel Load-Balancing Configuration:System: source-dest-ip
Port Channel Load-Balancing Addresses Used Per-Protocol:Non-IP: source-dest-macIP: source-dest-ip source-dest-mac
View 4 Replies
View Related
Mar 5, 2012
Is it possible to use two different load balancing methods at each end of a port-channel between two switches?
We have a Cisco 6509 at one end of the port-channel and a Cisco blade switch 3020 at the other end. Right now, we are using "src-dst-ip" at both end of the port-channel. We would like to change this. That is, we would like the #3020 switch to use "src-dst-ip" while the 6509 switch should use the "src-dst-port".
Why we want to do this, the reason is that we have FWSMs on the 6509. I've read that by configuring "src-dst-port" on the 6509, one can get a better performance of traffic going through the FWSM. However, the issue is that the 3020 switch does not support "src-dst-port".
View 4 Replies
View Related
