configuring 1142 ap for using centeal dhcp.Now i try to install another 1142 as a repeater for first 1142 point.
Here is root config:
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname 3floor
[code]....
I am a bit confused of the repeater functionality in the mentione AP, my concerns are:
1- Will each radio be dedicated to one function (for example 2.4 GHz for user access and 5.0 GHz for repeater functionality)?
2- Will the internet speed for users be affected when using the access point in repeater mode (no ethernet)?
3- Can an Autonomous AP function as a repeater?
4- Is there any license required?
5- What is the signal overlap requirements between the two Wired and non Wired AP?
6- Can the non wired AP be work as a repeater for another non wired AP (similar to cascading)?
How I install the WAP321 with repeater?
View 3 Replies View RelatedI'm trying to install an Engenius EAP9550, configured as a wireless repeater. the instructions are beyond abominable (as the review on Amazon warned). They tell me to enter 192.168.1.1 (which is my linksys E2000 wireless routers address, though they say nothing about that) and tehn give me no other information on how to configure or set this up.
View 13 Replies View RelatedI am having trouble setting up my Netgear N600 dual band wireless router as a repeater to my Lynksys EA2700 (main wireless router).
I am doing this because the main wireless router is in the "Man Cave," as I am a girl- I call it simply "The Cave." Anyway, the range on the N600 is supposed to be great. But from where it sits to where I sit and use my laptop or tabel is about 250 feet and goes through about 5 platered walls- so super thick.
I have here a canyon wireless router. do you know where I can find online a tutorial or manual on how to configure a wireless router so that it acts as a repeater?
View 3 Replies View RelatedI have a Netgear WGR614 wireless router connected to my WOW DSL modem and utilize WPA as security. wireless signal is good on first floor but drops significantly in my basement. I have a Netgear WG102 AP I would like to configure as a repeater and place in my basement to boost the WGR614 signal strength. What configurations must I apply to both or either devices to achieve this setup?
View 3 Replies View RelatedI'd like to give my DIR-655 (rev. A4, firmware 1.32) to my brother for use as a repeater, to work with the weak signal in his apartment. But I don't see any way to configure the device to join an existing wireless network. Am I wasting my time?
View 7 Replies View RelatedIs it possible to configure the WRT54G as a repeater signal of the WRT120N?
View 1 Replies View RelatedI would like to use my new EA6500 as the base station and another wireless router with Wireless Repeating Function as a repeater. Is the EA6500 capable of that?? I have not found any documentation on that subject.
View 6 Replies View RelatedI have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies View RelatedI'm very dissatisfied with the range and signal strength of my new WRT610N dual band router compared to the WAP54G Access Point I used before.Can I configure the Access Point as a repeater for the 2.4 GHz band on the WRT610N if I use the WRT610N as a Wireless G router rather than wireless N?
View 5 Replies View RelatedI've recently switched to a Verizon hotspot. For additional range while I'm at home, can I configure my Actiontec PK 5000 as a repeater for the hotspot signal?
View 2 Replies View Relatedim just want to ask a favor if you can guide me to set up or configure a router repeater to extend my wifi at my home. i dont have a specific brand of repeater yet.. im planning to buy but i have no idea how to set up a repeater by myself.
View 1 Replies View RelatedI just got UVERSE and they supplied a new router (or is it a gateway) and my F7D8301 is excess to me. Is there a way to configure the Belkin router as a repeater?
View 1 Replies View RelatedI have Dlink DWL - 2000AP+.
What I want to do is, to reproduce WiFi signal (from TP-LINK modem) by repeating with D-Link Wireless Access Point.
Here is how web interface looks. There is an option for repeating:
After clicking Site Survey I see all list of available networks. When I select one of them, the D-link saves changes then reboots. After that, Windows shows me something like that on available WiFi networks list:
<Repeated network name> 2
The problem is, when I connect to this network, Windows connects directly into root source, not to my WAP (I see this with inSSIDer utility).
Is it possible to configure a E2500 as router and WAP54G as a repeater? I used to have a WRT54GS as router but it has broken and now I bought a E2500 to replace it.
View 2 Replies View RelatedI am using a PPPoE connection using a linksys WRT54G router (working perfectly) and am now trying to set up an Edimax EW-7206APg to extend my wireless connection range. I followed the instructions given on the Edimax manual, and while my devices (iPad, laptop) got connected to the new repeater network, I could not access the Internet from it. I may be wrong, but the instructions on the Edimax manual seemed to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connection?My router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest.
View 6 Replies View RelatedThat's y topology:
(TPLINK) /////////////// (Huawei)--->(internet)
...................wirless................cable
I want to configure my tplink modem on a repeater mode in order to repeat the signal from (Huawei) ...
I am planning to install and configure VSS (6509) switches. But the customer requires that the First Switch should be the main and the second Switch should act as a backup one. (Disaster Recovery).
Once the Main (Primary switch) DOWN the Secondary one should coming UP.But what I am understand in VSS concept the two switches will act as one Switch. And both of them will be UP in the same time.
Is there any solution to configure the both VSS switch as primary and standby switch to provide HA?
I am replacing an A3 that's slowing dying with a B1. I understand the Firmware versions are different but I was curious if I can save the config file from the A3 and load it into the B1 ? I don't know if the config file includes the Firmware....
View 2 Replies View RelatedI have Cisco AP 1142 standalone and I want this one to operate with WLC.
I have searched in Google, they said I need to upgrade AP1142.
I don't know how to upgrade it.
i have a problem using my usb to serial cable connection, i can connect to one router on my work, but i can't connect to AP 1142, (i have tested also con AP 1231).i have a laptop running windows 7 64 bits, before i use a win xp 32 bits, and i didn't have problems.i am using putty, and have installed tera term 4.74 but the same.connection details, 9600, 8, 1, N, N.
View 5 Replies View RelatedI can't get connectivity from laptop to AP using cross over or straight through cable to do a tftp transfer from tftp server on laptop to ap.
I held the mode button on ap and powered on to get to rommon. The ap has no ios so it goes to rommon anyway. ap light is blinking red.
ap: set
DEFAULT_ROUTER=10.0.0.1
IP_ADDR=10.0.0.1
NETMASK=255.255.255.224
[Code].....
After AP is booted it shows the following message and cannot able to join in WLC:
*Mar 1 07:13:37.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.71.16 peer_port: 5246
*Mar 1 07:13:37.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
I just converted AP 1142 to LAP using the image "c1140-rcvk9w8-tar.124-21a.JA2.tar".
The WLC is a 5500 with 2 NIC : one on 192.168.0/24, one on a specific vlan 10.20/16
The main management interface is on 192.168/24 but we defined as management the interface on the 10.20/16 network.
For the access points, we use ports on a native VLAN on 10.20/16 with other available VLANS which are used for the wlan networks
We have 1152 APs which work fine on this config but that needed to be registered on the 192.168/24 network, then we moved them in their VLAN 10/20/16 and they work fine.
We also have 1142 APs which have been upgraded to LAP. These AP do not work with our architecture. They register correctly on the 192.168/24 network, but do not give access to the wlan VLANs. If they are moved in the 10.20/16 network, they don't register to the WLC (message : Timed out while waiting for ECHO repsonse from the AP). The AP do not get an IP.
is there a restriction with VALNs on these AP ? or is something false ?
I have an 1142 AP that I am unable to set back to factory defaults.Here is what I have done so far:
- boot AP while holding down the mode button
- ap: delete flash:private-multiple-fs
- yes
- ap: boot
- when the AP boots fully I try and enter any lwap ap commands and get "ERROR!!! Command is disabled"
- the AP name and password were reset to defaults but I am unable to get the IP address cleared.
I've also tried "clear lwapp private-config" and get an error saying the command is disabled.
I need to convert some 1142 APs to lightweight mode. They will connect to controllers running 7.3.101.0. I noticed there's two options of Lightweight IOS code available c1140-k9w8-tar.152-2.JA.tar and c1140-rcvk9w8-tar.152-2.JA.tar. Whats the difference between the two versions of code?
View 4 Replies View RelatedWhen we take a look at the internal antennas on the 1142 AP, we notice the 5ghz pointed all the same way, but for the 2.4ghz we can see each offset by 45/120 degrees. It was my understanding that all antennas are omnidirectionals on the 1142, why are those 2.4ghz antennas not all pointed the same way? onfiguration advantage and that each antenna is indeed omnicadirectional? Example, if I shut just one antenna off, do I lose a sector (120degree)?
View 5 Replies View RelatedI recently purchased another 1142 AP to expand out our current wireless infrastructure, my question is, what exactly needs to be done for this to work so that users can roam freely and auto-connect to the closet AP with the best connection without getting disconnected?
I have set all the settings the exact same on the new AP to match the existing AP. (How to save the configs into a file would be great, I am not sure how to do that)... But anyhow, before I launch it, I would like to be sure I am correct so I do not bring down the existing network. Of course, the only difference between the 2 are the IP addresses. AP1 is 192.168.2.2 and AP2 is 192.168.2.3
All computers are using Linksys Wireless-N cards.
The last three new APs I have received from our supplier (official Cisco 1142 LAPs) have all successfully connected to our 4400 series WLCs but are all reporting as being in an Operational Status of 'Down' ie their A/B/G/N radios are not broadcasting even though the APs are all in an enabled state. Furthermore, there is no steady green light showing on the APs - there is no light showing whatsoever (although they were displaying the familiar red-orange-green lights while they were pulling down the IOS images from the WLCs).
The only strange thing I have noticed is that in the AP config screen, the ‘Mini IOS version’ is shown as being v7.3.x. The other – working APs – we have of the 1142 series show v3.x. I know that controller code v7.2 and above only work with the newer 5500 and 7500 series WLCs. Could this be the issue and have any of you seen this issue previously? I am running WLC code v7.0.230.0.
that cisco ap 1142 will support WLC2506 or not .
View 2 Replies View RelatedI have WLC 2540 and AP 1142..i have configure them both and got connected(WLC can detect the AP) yesterday then i turn off them both and now when i powered up , the WLC cant detect the AP but AP and WLC can still ping each other they communicated at layer 2, both WLC and AP in one IP segment.
here some debug from AP
*Jun 21 13:49:47.784: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.3.2
*Jun 21 13:50:05.913: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceed., 1)x(UNKNOWN_MESSAGE_TYPE (5)
*Jun 21 13:50:05.913: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Jun 21 13:50:05.913: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10. 0.3.2:5246
*Jun 21 13:50:05.954: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jun 21 13:50:06.042: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[code]....