I am relatively new to Cisco CLI and on the diagram that I am attaching I want the 2008 server to do DHCP for everything behind E0 on the Soho 91. I have tried multiple configs and I seem to get close but never quite get it. I am thinking that adding a DHCP helper on E0 will work but I am not sure.
This is my current show run:
clock timezone akst -9
clock summer-time akdt recurring
no aaa new-model
[Code] ....
My team were going to purchase the Cisco 801's to build our SoHo. However, they are now EOL.
View 1 Replies View RelatedI have an ADSL connection which I would like to have my Cisco Soho 97 ADSL router configured to dialup and forward to port 8080.
My network is 192.168.1.0/24
Router is 192.168.1.1
Server is 192.168.1.4 - Default gateway is 192.168.1.1
I am able to connect using the script below and get a public ip address but i cant get it to connect to the internet?what command to use for port forwarding to 8080?
hostname Router
!
!
ip subnet-zero
ip name-server 212.23.8.1
ip name-server 212.23.3.1
ip dhcp excluded-address 192.168.1.1
[code]...
How the ACL Ports/Protocols which must be opened (in- and outbound) to enable a communication between a CISCO Office extend AP and a 5508 WCS.
View 3 Replies View RelatedHow can I give endpoints public IPs, that I can remote to or access (electronic whiteboard) from the Internet using a soho router? Will I need to purchase more than one public IPs or is there something I can do with subnet masking?
View 1 Replies View RelatedMy Setup / I've been lurking on here a while, working hard to understand the basic networking concepts and eventually pursue the CISCO certs. I bought a lab and have since managed to setup a four router config (2610XM-DTE, 2621-DTE, 2501-DCE, and a linksys E1000 with routing, DHCP, and NAT turned off to make it a wirelss access point) with three switches (2@2950 and a 2924XL).
So far, I have managed to bring in my public IP using DHCP, and setup PAT. The network is fully functional, I can ping every interface, and reach the web on host PCs from any switchport. I am also able to telnet into the FastEthernet interface IPd with my public address.
My Issue : My concern right now is in feature support. I recently read on here that CISCO does not support UPnP, and due to my limited resources, I am using the only public IP I have to allow remote testing/learning on my lab. The issue is that I also have a PS3 and XBox 360 on this network that is requiring UPnP for certain online games and features.
The only solution I can see to this problem is to return my public IP back to the E1000 router, which is running RIP Version 2 (white papers said version 1, but a debup ip rip showed that updates were being ignored due to illegal version), and then poing my other three routers to it for outside access.
The questions I have in this scenario:
1. Will NAT still function if I use the E1000 and set the interfaces connecting to it as ip nat inside? I'm assuming that PAT is already hardcoded onto the router to allow for multiple connections to public IP space.
2. If my IP is 68.X.X.X, I set the E1000 to an IP of 192.168.1.1 and the FastEthernet it connects to is on my 2621 with an IP of 192.168.1.2, would it be possible to telnet into 192.168.1.2? If I were to forward port 23 out of the E1000 to the 192.168.1.2 address. Will my login and password for line vty 0 4 understand the request if the original telnet was to my public IP?
3. If all of that is just non-sense, is there another work-around that allows me to acheive UPnP through my E1000, while retaining telnet ability to my lab so I can try things in different scenarios or while I'm away from home?
how I can give endpoints on a SOHO router network Public IPs so I can access an Electronic Whiteboard over the Internet. Do I need to purchase more that one Public IP or is there something I can do with subnet masking?
View 2 Replies View RelatedI am having a problem reaching a soho linksys e1000 router through a second hop cisco 2900 router.Here is a brief topology of the network: I am using OSPF area 100 for all networks except for
192.168.2.0 on R1 to E1000 which is RIPv2
R1 directly connects to R2 with a point-to-point serial on network 192.168.12.0 /30 with ip 192.168.1.13
R1 directly connects to a a switchport using network 192.168.2.0 /24 with ip 192.168.1.75
R3 directly connects to a switchport using network 192.168.1.128.0 /25 with ip 192.168.1.129
R3 directly connects to a different cisco router using ethernet on network 192.168.1.0 with ip 192.168.1.1
E1000 directly connects to a switchport using network 192.168.2.0 /24 with ip 192.168.2.1
The switch has a vlan ip on 192.168.1.128 /25?I can ping from R1 to E1000?I can ping from R3 to R1 192.168.2.75? I can't ping from R3 to E1000 192.168.2.1?show ip route on R2 indicates that network 192.168.2.0 is reachable via the serial connection on 192.168.1.12?I have redistributed rip to ospf area 100 and OSPF to RIP on R1?I am wondering why R1 can reach E1000 on network 192.168.2.0, and why R3 can reach R1s 192.168.2.0 newtork, but R3 can't reach the E1000.There is an R2 router than can reach R1 and also cannot reach E1000, but I assume it's for the same reasons R3 can't, so I've omitted the remainder of that topology for this question.
If it's possible, how do you protect/block a unauthorized DHCP SOHO router with NAT form a Cisco 3750?
View 16 Replies View RelatedI am definitely not a fan of ios 8.3, and specialy the change about "nat". I trying to use this example : [URL]
everything is good except : global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 172.16.1.0 255.255.255.0 Because, this example is for an 8.2 ios (or above), and i have a 8.3.
Another question : What the bestway to use this example, but with a single "nat" for all outbound traffic (I want all outgoing traffic (on the main FW) to be seen from a single domain encryption)
I have inserted a SIP-800 card into my CRS-8. I inserted the SPA into the SIP. I cannot find how I configure the SIP or the SPA. I have spent the day reading the manual but no where do I see the commands to activate or get the SIP up and running.
View 1 Replies View Relatedi want to configure a new cisco 1812.what i want is : we have 5 external ip addresses from our ISP.we want that the FE0 ( wan port ) can route all those ip addresses.so when we put a firewall on port number 8 with 1 of the 5 external ip addresses we have internet.and when we put a firewall with another external ip adres on port 4 we have internet.
View 6 Replies View Relatedi looked but didn't find anything. I'm looking for a configuration guide, similar to the ASA Configuration Guide, that that can provide documentation on how to configure a Cisco 3925e router. I have my CCNA and a fair amount of real world experience configuring routers but ultimately what I am looking for is guidance on how to configure BGP on this beast. I learned a great deal about ASAs by running through the ASA Configuration Guide and I am hoping to do the same with the 3900 series ISRs.
View 5 Replies View RelatedWe have a MPLS T1 installed at the main office. I just purchased ASA 5505 to configure site to site VPN connection. The ISP have VIP mapped with 1 block of public ip addresses.configure the asa 5505.
View 0 Replies View RelatedI would like to ask some thing for configuration on AP (AIR-LAP1141N-A-K9) but now i chnage IOS to stand along mean and i want to configure QOS on this AP? Any command how to configure QOS?
View 2 Replies View Related- the WAN consists of a in-house satellite network using comtech CDM-570 IP-Enabled Satellite Modems
- there is a group of HUB tx modems, each one is shared for approx remote 10 sites with a total bandwidth tx 2048k
- each remote site is to be guaranteed min 512k but can burst into the 2048
- remote sites must be somehow grouped to a member of each modem to set the bandwidth constraints
- a single DMVPN/multipoint GRE is configured on HUB. all remote sites connect to this (redundancy comes later )
The challenge is how to configure the QoS on the HUB side to meet this policy, Currently, I use ip nhrp group MODEM1 on each remote site, and ip nhrp map group MODEM1 service-policy output MODEM1 on the HUB. This is working ok. This works nicely, however I am left with the constraint that within each modem group I must define a class for each site and set the guaranteed bandwidth. As the policy is applied pre-encapsulation, I must create a class with an acl matching the remote sites IP ranges. An administration nightmare and prone to failure! I want to avoid this if possible.
I have Switch 6509E wich is the core of the network, and we have 4 llink form 4 ISPs, all the link will work at the same time?how can I confiugure the BGP , as I know if I configure bgp it will work with one ISP as an active link,if that link goes down it will automatically begin to work with other ISP. My question is that how can configure the network so that,some vlans work with one ISP, some vlans with the others and so on.If configure it with route map I will have to track every time to change the confiration if the links goes down, but I do not want to track it, Can I do anything with BGP to implement this task?The core of the network is Switch 6509E, intervlan routing is implemented on it, no dynamic routing is enabled.The firewall module installed on it the implementing the NAT processes.
View 7 Replies View RelatedI have a Cisco 1802 to connect my company to ADSL over ISDN. But my boss wants to change the ISP. The propose was (still is) to configure de router with VPN, IPS and use the WAN port to connect the new ISP, that provides an Ethernet signal to 100Mbps.The WAN port will work with Ethernet signal (when we change of ISP)?Any good book (or a paper) to configure the router to work properly with VPN and IPS?
View 2 Replies View RelatedWhat specific commands are needed to configure qos on a router?
Two sites:
Cisco 2911 (site 1 ) Cisco 2911 (Site 2)
Data Vlan
Management Vlan
I want to configure QOS on Site 1 where the Data Vlan traffic is always marked higher than the management Vlan coming from Site 1.
I have one router 2911 with the following image c2900-universalk9-mz.SPA.151-4.M4.bin I have two IPS on this routers and I tried to configure the IP SLA on this and I`m not able to do it and I don´t know why. I can configure almost everything but not the IP SLA command.this is the config:
track 10 ip sla 1 reachability
delay down 10 up 1
!
track 20 ip sla 2 reachability
delay down 10 up 1
!
[code]....
What I need to do in this case? or why cannot configure the IP SLA?
I have configured a cisco router 877 to run the Dynamic DSL. However, it cannot work, the ATM 0 interface cannot be up . Here is my configuration:
version 12.4
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime
no service password-encryption
[code]....
I am going to configure the NATing on ASR1002 and expecing to have near about 1Million nat translation. Will ASR1002 support 1million nat translations ? how many NAT translations are supportable on the ASR1002 ?I am going to configure NAT on ASR1002-5G/K9 U& have FLASR1-FWNAT-RED.
View 1 Replies View RelatedWe heard that ASA ver 8.4 has PBR. Do we have some guidelines on how to configure PBR for ASA and can it do routing based on URL?
View 2 Replies View RelatedIf I have SIP-200 and I need to configure a feature , for eg - PPP on SIP-200 , is it something possible ? If Yes how I can do that in IOS ?
View 1 Replies View RelatedI currently have a Cisco 891 running with a FTP running on port 21. I currently have the NAT from external IP to and internal IP 192.168.12.6 for port 21. And the firewall allowing that traffic through and client software is working fine. However I need this FTP to be running on port 990 and anytime I change the NAT and the firewall, the external FTP clients connect but then drop when recieving the directory listing.
View 18 Replies View RelatedHow to configure MAB (Mac Authentication Bypas) in ACS 5.2 or ACS 5.3.I have running tacas+ & radius on the ACS with a local database
I have entered already a list of MAC address in the Users and Identity Stores / Internal Identy Stores / Hosts .Also I have already a Access Policies configured. Access Policies / Service Selection Rules / MAB
And a group "Host Lookup" Host Lookup has the service type : Network Access And policy structure : Identity & Authorization.
I have a SF 300-24p.... How do I configure it to act use like a hub, with the uplink on G1... And How do you set all the ports to POE for ViOP phones, and these ip phones are going to get DHCP over network..
View 1 Replies View RelatedI have a Cisco air lap1510ag-a-k9, that i which t configure, but i do not have a WLC
How can i configure this router without WLC or WCS
I'm trying to configure a Cisco 3800 with a WIC-2AM-V2 to do DDR. I've gotten it to work before, but it was a while and now the config doesn't seem to work. I'm using an Lo0 interface and ip unnumbered on the Dialer interface. Using debug dialer and debug ppp and see nothing at all trying to dial out.
##############################################################
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname DDR
[code].....
I'm baffled by a lot of new features of LMS4.2 and seem lost where to start looking.Our client needs to periodically make changes to switches to change their port settings.They have specific descriptions with a certain string. Let's say the description say "Cisco phone".The task is to create either template or ad-hoc Netconfig job that will send changes only to those switchports.
View 2 Replies View RelatedI would like to configure a vpn l2l ipsec for a friend. i have a router cisco 877 i configure it but vpn doesn't work.Above my configuration:
Current configuration : 5443 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Laboratorio!boot-start-markerboot-end-marker!!aaa new-model!!aaa authentication login default localaaa authorization exec default local!aaa session-id common!resource policy!ip cefno ip dhcp use vrf connectedip dhcp excluded-address 172.16.1.1ip dhcp excluded-address 192.168.1.1ip dhcp excluded-address 192.168.1.254!ip dhcp pool HostPc network 172.16.1.0 255.255.255.0 default-router 172.16.1.1 dns-server 8.8.8.8 8.8.4.4!ip dhcp pool MPLs network 192.168.1.0 255.255.255.0 default-router 192.168.1.254 dns-server 8.8.8.8 8.8.4.4!!!!crypto pki trustpoint TP-self-signed-4019649088enrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-4019649088revocation-check nonersakeypair TP-self-signed-4019649088!!crypto pki certificate
[code].....
I want to create a VPN server on a linux Box for our company. I need to connect via VPN on private local company network and then i get the public ip address from here (company public ip address). This is because some of our system is only accessible from static company public ip, and the problem is the remote access (from home for example) to this systems.
How can i configure this VPN Server and what client can i use to connect and get the public ip address from the company and then connect to company systems?
How to configure 2 NIC in 1 PC?
View 1 Replies View Related