Cisco Wireless :: 2500 WLC Ports Auto Negotiate?
Apr 1, 2012I see the 2500 porst are 1 Gigabit ports. Are they 10/100/1000 ports though?Have an older switch that only has 10/100 ports.
View 2 Replies
ADVERTISEMENT
Cisco :: C3750 / IOS - Set Ports To Auto-negotiate In Bulk?
Jun 28, 2012Building was recently upgraded from cat3 to cat6 wiring and I'd like to ssh into each Cisco C3750 stack and change every port on the stack to autonegotiate. I can release each port one at a time by doing "no speed" and "no duplex" after selecting each port (interface fastethernet x/x/x) , but it's taking forever as there are many stacks and each stack has a number of 24 and 48 port switches. The stacks are a mix of fastethernet and gigabit ports (C3750 and C3750G switches) if that changes anything command wise.
View 2 Replies View RelatedCisco Switching/Routing :: 7600 Service Provider Has 1000-Full With Auto-negotiate
Jan 21, 2013I have a port on 7600 connecting via Single Mode Fibre to my service provider. Service provider has 1000-Full with auto-negotiate. I am seeing following output on my 7600. [code] if this interface is only capable of doing 1000Mb, how come it is showing 100-Full. If I change to nonegotiate option (both my side and provider side), link goes down. My provider has confirmed they have 1000Full their side.
View 2 Replies View RelatedCisco :: Auto-negotiation For Ten-giga Ports?
Mar 14, 2013I have already exploited Metro Ethernet, but I don't understand why auto-negotiation does not support for Ten Giga ports?
View 8 Replies View RelatedCisco Wireless :: AP 1262 Don't Negotiate With Gig Interface
May 9, 2012I have new 1262 APs, this have Gig Interface, when I connect the AP in my 6500 with PoE Gig Interface, the AP turn on, but the interface never get up. I need to change the speed to 100 in the 6500 switch port, when I do this, the interface become UP.
This is the model of the card WS-X6148A-GE-45AF This is the Switch IOS s3223-ipservicesk9_wan-mz.122-18.SXF11.bin
The controller is 5500 version 7.2
This is the interface config:
interface GigabitEthernet4/36
switchport
switchport access vlan 308
[Code].....
Cisco WAN :: 887 / PPP - LCP Failed To Negotiate
Mar 16, 2013I have a cisco 887 router and I have tested on two different DSL line. The first line it worked fine with while the other noe is not. both line on same exchange and establishing the ppp session with same BRAS. The debug seems that there Establishing phase failed, but my question here is how our BRAS will faied the establishing from on line while from other landline is working fine.
=============================================================
CISCO ROUTER Configuration
=======================
interface ATM0/1/0no ip addressno ip mroute-cacheno atm ilmi-keepalivedsl operating-mode autopvc 8/35encapsulation aal5mux ppp dialerdialer pool-member !interface Dialer1ip address negotiatedip nat outsideip virtual-reassemblyencapsulation pppdialer pool 1ppp chap hostname companyxppp chap password abcda123ppp pap sent-username companyx password abcda123
===========================================
when I did ppp negotiation debug the below messages i got:
============================================
Mar 16 13:19:18.103: Vi2 PPP: Phase is DOWN
Mar 16 13:19:19.103: PPP: Alloc Context [85DEC77C]
Mar 16 13:19:19.103: ppp28 PPP: Phase is ESTABLISHING
Mar 16 13:19:19.103: Vi2 PPP: Using dialer call direction
Mar 16 13:19:19.103: Vi2 PPP: Treating connection as a callout
Mar 16 13:19:19.103: Vi2 PPP: Session handle[700001C] Session id[28]
[code]....
Cisco VPN :: 7600 - Cannot Successfully Negotiate ISAKMP Phase 1
Apr 22, 2012I am trying to set up a site to site VPN tunnel using GRE over IPSEC. Below is the configuration from both routers and debug output. I'm scratching my head on this one. I'm using two Cisco 7600 routers with SSC-400 SPA modules and 720 Supervisors. The IOS on R1 is 12.2 SXI2 and R2 has 12.2 SXI3.
View 1 Replies View RelatedCisco Wireless :: 2500 WCS Can't Add Controller
Nov 20, 2011I am having trouble adding a new controller(2500) to the WCS.
-My WCS version 6.0.196.0
-My WLC version 7.0.116.0
If i upgrade my WCS i may add the new contoller? Even if in cisco DATA-SHEET there isnt any mention regarding this WLC(basicly it says that the WCS does not support this WLC)
Monitoring and migration of selected Cisco Aironet standalone (autonomous) access points. Monitoring of the standalone access points of Cisco 800, 1800, 2800, and 3800 Series Integrated Services Routers.
Cisco Wireless :: WLC 2500 With AD Integration
Jan 3, 2012I have a scenario where we have
Cisco 1300 Outdoor APs
Cisco 3600 Indoor APs
WLC 2500
Now i need to integrate the WLC with Windows 2008 AD for authentication.The idea is to let the users authenticate via AD for accesing the wireless network.
Will the integration work with NPS?
Cisco Wireless :: 2500 - LAP Management
Feb 15, 2012I'm configuring a 2500 series WLC to test some wireless configuration changes we'd like to make on our 5500's that are currently in prodcution.
The 2500 and the 5800's interfaces are configured as a LAG.
One of the primary goals of these configuration changes is to move the LAPs from their current VLAN (the same subnet as our primary WLAN) to two separate VLANs. Were choosing to move the LAPs to 2 APs based on the WLC best practices document's suggestion to limit the number of LAPs per vlan to 60-100. We've had several issues in the past with LAPs failing to join with their static IPs, releasing them and then joining with DHCP addresses.
LAP's will be on separate vlans using subnets 10.10.10.0/25 and 10.10.10.128/25. WLC management interface is in the 10.10.1.0/25 subnet.
Should we continue using static IPs for the LAPs or DHCP?
What subnet should the AP management interface be on?
Is it possible to have mutiple AP management interfaces with LAG?
Cisco Wireless :: HA Support On 2500 Controller
May 10, 2013By any way can I achieve HA in 2500 controller? I dont mind even I didnt get Stateful switchover.
View 5 Replies View RelatedCisco :: 2500 How To Secure Wireless Network
Aug 2, 2011We are looking at MAC address filter on the WCS (Limted to 2500?) for the machine then a rule on the ACS pointing to an AD group.
View 1 Replies View RelatedCisco :: Wireless Controller With Web Authentication 2500
Dec 7, 2012i am having wirless controller cisco 2500 series. i want to know how many web authentication users i can create in the 2500 series controller with time out option for each users.
i know it will support the web authentication for internet access for the users but i need to know how many it will accept at a time with hours specification.
Cisco :: LMS Support For 2500 Wireless Controller?
Nov 27, 2011know if Cisco LMS will ever support the 2500 wireless controller ? I have just checked the supported devices for LMS 4.1 and the controller is not there.
View 1 Replies View RelatedCisco Wireless :: 2500 - Compatibility Matrix
Apr 3, 2012I have some concern regarding the compatibility of AP with the WLC. we are using AIR-CT2504(7.0.116.0) series WLC with AP AIR-LAP1242AG(7.0.116.0) but now i checked on Cisco website they are End-of-Sale/End-of-Life for the Power Supply for Cisco Aironet 1130, 1140, 1240 and 1300 Series Access Point.
Now My question is:
1: Which is the latest AP series we should use for WLC 2500 series?
Cisco Wireless :: WLC 2500 Client Limit?
Apr 18, 2012Im making a design for a customer that will have around 200 wireless users.
We were thinking in the WLC 2500, because the number of APs will be around 30.
But the problem is that from time to time, the client organizes events, and in these events the number of wireless clients will be around 600.
In the WLC2500 specs te maximun numbers of users is 500, but i want to know if this is just a recomendation, of if the WLC will drop the connection attemp # 501.
Cisco Wireless :: MIBs For 2500 Series WLC
Apr 25, 2012I need the MIBs for Cisco 2500 WLC. I have it for 5508 WLC. Does it works same for 2500 WLC too ?
View 1 Replies View RelatedCisco Wireless :: Use 5500 And 2500 WLC As Failover?
Mar 4, 2012The 5500 WLC would be the primary and 2500 WLC would be the secondary. The only need for the secondary would be in the event of failure of the primary, and support needs when doing maintenance such as code upgrades.
We would use the same version of code on each controller and apply the necessary amount of AP licenses on each. The controllers would have identical configurations and host multiple SSID's, including offering guest services. Does the 2500 support guest network services?
Linksys Wireless Router :: Cannot Set Up 2500
Jan 31, 2013Cannot set up 2500 router
View 8 Replies View RelatedCisco Wireless :: 2500 Series Machine Authentication With IAS
Jun 2, 2013I have the problem with machine authentication, our customer using Wireless Controller 2500 Series and need implement machine authentication on IAS server. So, as my understand is our controller may not change anything with configuration but we may configure IAS for support machine authentication, correct? but my question is how to? and is it work ?
View 24 Replies View RelatedCisco Wireless :: 2500 As Anchor / Compatibility And Limitations?
Jan 29, 2013with FW 7.4.100.0 a 2500 controller works as anchor controller, now.I have 3 questions.
1) What are the limitations? 15 EoIP tunnel, Clients? something else?
2) Have Cisco a compatibility matrix about Anchor - Foreign Firmware? (Example works 7.4.100.0 anchor with 7.0.x.x foreign?)
3) A controller works only as anchor. A controller version with lowest AP licence is needed. Right?
Cisco Wireless :: CAP1602I-E-K9 Can't Register With 2500 Controller
May 18, 2013I am developing CAP1602I & 2500 Controller.The CAP1602I-E-K9 can't register with the 2500 controller. [code] logging appears: capwap can't process uncryped data..I even didn't configure capwap on CAP1602.May I know if CAP1602 doesn't support LWAPP? Why LWAPP doesn't work?According to the logging, I also tried to configure the "Data Encryption" on 2500 controller ( according to 7.0.116.0 guide)
"Cisco 2500, WiSM2, WLC2—By default, these platforms do not contain DTLS. To turn on data DTLS, you must install a license. These platforms have a single image with data DTLS turned off. To use data DTLS you will need to have a license."Note If your controller does not have a data DTLS license and if the access point associated with the controller has DTLS enabled, the data path will be unencrypted. I should purchase a license? or, if I can configure the CAP1602I to don't encrypt data?
Cisco Wireless :: How To Configure WLC 2500 With Authentication 802.1x EAP TTLS
Mar 14, 2013My client wants to test their new product with wireless authentication 802.1x EAP TTLS. They have CISCO WLC 2504. Does CISCO WLC 2500 support EAP TTLS, if yes then how to configure. So far I have added Radius TTLS server into my WLC. Under Radius on WLC added radius server IP and key and created new SSID 802.1x WPA+WPA2 ( WPA policy2 and WPA encryption AES) after that under SSID AAAservers selected drop down same server IP. But user tried and didn’t work also we didn’t see any hit on radius server. Yea policy has added on radius. My client wants to use TTLS instead of TLS because in TLS you have to use client certificate on client side but on TTLS you can use certificate on client side but it is optional. So they want to stick with TTLS. But I am not seeing any documentation on TTLS with cisco WLC
View 8 Replies View RelatedCisco Wireless :: WLC 2500 Authentication Using Multiple AS Domains?
Mar 13, 2012The users belong to Multiple AD domains. If we purchase WLC 2500 controller. Can I have one more WLANs authenticate to multiple radius or ad domains? I thought one WLAN/ ssid authenticate to single radius server.
View 4 Replies View RelatedCisco :: 2500 Wireless Controller Blocking Traffic
May 16, 2012I have a Cisco 2500 Wireless Controller connected and controlling 5 Cisco AP's. Everything works fine except one device.
This device is used to connect to our AP wirelessly and then any of the wireless laptops can use programming software to connect to the device and program through it. I can successfully set up our device on the network and all PCs can ping it, but the programming software refuses to connect to it. I spent an hour and a half on the phone with the device people who assure me its the network. So, I bought in a cheap Linksys router, hooked one laptop up to it and configured the device wirelessly. With that, the programming software works.
what should I be looking for in the Wireless Controller that may be blocking direct connection to the device even though I can ping it?
Cisco Wireless :: 2500 Series WLC Crashed Repeatedly
Aug 11, 2012I have 2500 series wlc which is crashing again and again. I attach the log of crash as well.Also in License location the base-ap-count license " is not in use ".
View 3 Replies View RelatedCisco Wireless :: Access Points Which Are Not Registering With WLC 2500
May 1, 2013We have a couple of Access Points which are not registering with WLC 2500. I followed-up on the two LAPs in the dorm. They were cycling through red, amber, green, indicating they were trying to join the controller but could not.
Recently, we have changed our IP Schema for the Wireless Devices and I believe there is an IP Conflict between APs and WLC. Earlier APs were cofigured with Static IP Address assignment, thus they can't change their IP Address.
how to reset the Access Point? I know we can hard reset them by pressing the Mode button manually.
Is there another way via which this can be done witout removing the Access Points from their enclosures?
Cisco Wireless :: Configure WLC 2500 With Authentication 802.1x EAP TTLS
Mar 14, 2013My client wants to test their new product with wireless authentication 802.1x EAP TTLS. They have CISCO WLC 2504. Will CISCO WLC 2500 support EAP TTLS, if yes then how to configure.
So far I have added Radius TTLS server into my WLC. Under Radius on WLC added radius server IP and key and created new SSID 802.1x WPA+WPA2 ( WPA policy2 and WPA encryption AES) after that under SSID AAAservers selected drop down same server IP.But user tried and didn’t work also we didn’t see any hit on radius server. Yea policy has added on radius.
My client wants to use TTLS instead of TLS because in TLS you have to use client certificate on client side but on TTLS you can use certificate on client side but it is optional. So they want to stick with TTLS. But I am not seeing any documentation on TTLS with cisco WLC?My android phone galaxy II has TTLS option under EAP 802.1x, so android devices support TTLS.
Cisco Wireless :: 2500 WLC Primary DHCP Server?
Apr 26, 2013If I set a primary DHCP server in the interface configuration, or if I override DHCP in the WLAN Configuration.Which interface does the WLC use to try and connect to the DHCP on behalf of the wireless clients?IFA) The dhcp server is not on any of the configured subnets.B) The DHCP server is on a different interface's subnet.
View 4 Replies View RelatedLinksys Wireless Router :: E-2500 IPhone Will Not Log On
Feb 8, 2012I purchased a new E-2500 router and got it operating my computer, but my iphone will not log on, I set up guests and now it appears to log on, but doesn't.
View 1 Replies View RelatedCisco Wireless :: 2500 / 5500 - Wireless Access Point Identification By Clients
Apr 30, 2012We have recently been given this unusual task. The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition. Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?
Cisco WAN :: 2500 - Controller Channel / Setting Up Wireless Badges
Feb 14, 2013We are currently using a Cisco 2500 (licensed for 50 AP's) WLAN Controller. There has been a lot of issues setting up the VOCERA wireless badges, thats on going. The question I have is all the AP's are showing as being on Channel 6, it was thought that the controller would learn the enviroment and move these to none overlapping channels, but has not. Is this right should they all be on the same channel and not 1, 6, 11 accordingly? it is also worth mentioning that the controller can see 61 rogue AP's, yes that is 61 other wireless networks!
View 2 Replies View RelatedCisco Wireless :: Comparison Of Features In Wi-Fi LAN Controller 2500 And 4400?
Jul 27, 2011give me the run down on the features removed from the 4400 series in the 2500 series? Obviously 4400 is now EOL, and so i cannot purchase new. Therefore I was looking at the 2500 for my implementation to save costs also.I would like to have two SSID's, running seperate VLAN's, one voice, one guest, trunk the link to the AP's, which will be 1131AG or newer, N possibly. Voice needs to be encrypted with WPA or WPA2, guest needs to be open using the guest access feature. Here's a sample but with EAP:
[URL]
Is this supported to have WPA on one SSID and Guest access on the other? i did spot a paragraph in the 4400 manual stating that certain restrictions apply regarding one SSID having encryption and the other being guest mode?I notice also in the WCS documentation, it doesn't explicitly state it supports the 2500 series under the managed devices section?