Cisco WAN :: 887 / PPP - LCP Failed To Negotiate
Mar 16, 2013
I have a cisco 887 router and I have tested on two different DSL line. The first line it worked fine with while the other noe is not. both line on same exchange and establishing the ppp session with same BRAS. The debug seems that there Establishing phase failed, but my question here is how our BRAS will faied the establishing from on line while from other landline is working fine.
=============================================================
CISCO ROUTER Configuration
=======================
interface ATM0/1/0no ip addressno ip mroute-cacheno atm ilmi-keepalivedsl operating-mode autopvc 8/35encapsulation aal5mux ppp dialerdialer pool-member !interface Dialer1ip address negotiatedip nat outsideip virtual-reassemblyencapsulation pppdialer pool 1ppp chap hostname companyxppp chap password abcda123ppp pap sent-username companyx password abcda123
===========================================
when I did ppp negotiation debug the below messages i got:
============================================
Mar 16 13:19:18.103: Vi2 PPP: Phase is DOWN
Mar 16 13:19:19.103: PPP: Alloc Context [85DEC77C]
Mar 16 13:19:19.103: ppp28 PPP: Phase is ESTABLISHING
Mar 16 13:19:19.103: Vi2 PPP: Using dialer call direction
Mar 16 13:19:19.103: Vi2 PPP: Treating connection as a callout
Mar 16 13:19:19.103: Vi2 PPP: Session handle[700001C] Session id[28]
[code]....
View 4 Replies
ADVERTISEMENT
May 9, 2012
I have new 1262 APs, this have Gig Interface, when I connect the AP in my 6500 with PoE Gig Interface, the AP turn on, but the interface never get up. I need to change the speed to 100 in the 6500 switch port, when I do this, the interface become UP.
This is the model of the card WS-X6148A-GE-45AF This is the Switch IOS s3223-ipservicesk9_wan-mz.122-18.SXF11.bin
The controller is 5500 version 7.2
This is the interface config:
interface GigabitEthernet4/36
switchport
switchport access vlan 308
[Code].....
View 5 Replies
View Related
Apr 1, 2012
I see the 2500 porst are 1 Gigabit ports. Are they 10/100/1000 ports though?Have an older switch that only has 10/100 ports.
View 2 Replies
View Related
Jun 28, 2012
Building was recently upgraded from cat3 to cat6 wiring and I'd like to ssh into each Cisco C3750 stack and change every port on the stack to autonegotiate. I can release each port one at a time by doing "no speed" and "no duplex" after selecting each port (interface fastethernet x/x/x) , but it's taking forever as there are many stacks and each stack has a number of 24 and 48 port switches. The stacks are a mix of fastethernet and gigabit ports (C3750 and C3750G switches) if that changes anything command wise.
View 2 Replies
View Related
Apr 22, 2012
I am trying to set up a site to site VPN tunnel using GRE over IPSEC. Below is the configuration from both routers and debug output. I'm scratching my head on this one. I'm using two Cisco 7600 routers with SSC-400 SPA modules and 720 Supervisors. The IOS on R1 is 12.2 SXI2 and R2 has 12.2 SXI3.
View 1 Replies
View Related
Jan 21, 2013
I have a port on 7600 connecting via Single Mode Fibre to my service provider. Service provider has 1000-Full with auto-negotiate. I am seeing following output on my 7600. [code] if this interface is only capable of doing 1000Mb, how come it is showing 100-Full. If I change to nonegotiate option (both my side and provider side), link goes down. My provider has confirmed they have 1000Full their side.
View 2 Replies
View Related
Jan 19, 2012
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies
View Related
Apr 11, 2012
UTMajoracquisition failed to run in LMS 4.0.1..
Troubleshooting done
1) Started the UTMajorAcuisition process manually using pdexec: It again fails to run
2) Renamed to ut.properties.orig to ut.properties and tried to restart the process .. IT again fails to run.
View 0 Replies
View Related
Aug 6, 2012
I can't inventory a 4507R + E / SUP7E Version 15.1.1 SG with the last version of LMS 4.2.1. Next, the extract of IC_Server.log.
[code]....
View 6 Replies
View Related
Sep 25, 2011
I have installed Ciscoworks LMS 3.2 0n windows server 2003 enterprise edition. I have issue with Campus Manager while accessing any thing in Campus Manager it is giving following error.
"Error in loading properties from the server" "Can not contact to ANI server" Status of ANIServer process is Failed to run
I tried to reinitialize Campus Manager Database still it is showing same issue.
Installed Campus manager version 5.2.1 check attached file for ANI log
View 5 Replies
View Related
Aug 31, 2012
[code]....
Red error what is the reason? Only appears in the window 2003 server.
View 5 Replies
View Related
Sep 18, 2011
I have issue with the ANI Server process, which fails to start. The LMS version is 3.2. It's recently installed, with just one device added to the database so far. I've read some similar cases in the forum, but I'm starting a new thread since it could be a different issue which causes the problem.Please, find attached ani.log, ANIServer.log, the output of the pdshow command and ANIServer.properties files. I doubt that the last one might be corrupted for some reason.
View 4 Replies
View Related
Aug 29, 2011
For quite some time now, we have been experiencing an issue with the Cisco VPN client that will make the client completely unusable. I have noticed that when a specific feature of Symantec Endpoint Protection is enabled, it will (about 25% of the time) cause the following errors to appear when attempting to connect anywhere with the Cisco VPN client. Once this error happens once, the VPN client then becomes useless.
Error #1
Reason 414: Failed to establish a TCP connection
Error #2
Reason 440: Driver Failure
Error #3
Reason 442: Failed to enable virtual adapter
It seems that fixing one error will cause the other error to come up.I have tried reinstalling the client with the same version and older versions and the issue still comes up. All users in the company are using Windows 7 64-bit with SP1 installed.The oddest thing about this is that all employees in the company have the same antivirus with the same features enabled, however, it only happens to a small percentage of employees.
View 3 Replies
View Related
Aug 21, 2012
I am facing a failed issue when restoring the WCS Database. Below is the error i get, does any one out there facing it before?
#######################################
[root@egwgwcs WCS7.0.220.0]# ./Restore
Please enter the full path of the backup file name: /opt/WCS7.0.220.0/Backup_File/WCS_Aug2012.nmsbackup
Untaring the backup file...
Failed to untar backup file. Exception: invalid stored block lengths
Restore database failed.
#######################################
View 1 Replies
View Related
Oct 17, 2011
I have Cisco Works LMS 4.0 on Win 2K8 64 bits on VMware EXs. I am facing issue with reference to Inventory Collection, my 10% devices (including Routers & Switches) Inventory collection is failed and give me error (Device sensed, but collection failed). I increase the SNMP timeout 10 sec, 30 sec, 60 sec and even 100 sec the result be the same.
View 1 Replies
View Related
Aug 17, 2011
I have a problem with the User Tracking and Data Collection on LMS 4.0.1 . I think It crashes every time or freezes. I Have this error if I lunch UT Acquisition :
Failed to start acquisition: Construction of XML data required for UT IS in progress. Please try After Some Time.When scheduling a CM data collection, I have this error: Data collection IS Already in progress.
I detected an error in ani.log line 12266: Exception in thread "Discovery" java.lang.AbstractMethodError: com. cisco. nm. ani. server. topo. Port Channel.portIfIndex ()
I successfully changed the name of the CiscoWorks server last week with the tool hostnamechange.pl.
Perhaps there was an impact on data collection ?
View 2 Replies
View Related
Aug 31, 2011
I got a report from a branch office which is getting trouble to authenticate users to the WLAN this is a stand alone AP which has a configuration script that we use for all our branch offices but in this case is not working. It seems to be an issue with RADIUS but if it was the case the whole company would be experiencing problems since it is a central RADIUS server.
Here is a log from the AP By the way I modified the radius server timeout to 90 sec
APIMMEXP01#
Sep 1 17:01:47.240: %DOT11-7-AUTH_FAILED: Station 0021.5c7f.1739 Authentication
failed
Sep 1 17:01:53.503: %DOT11-7-AUTH_FAILED: Station 0026.c64b.c3d6 Authentication
failed
Sep 1 17:01:58.739: %DOT11-7-AUTH_FAILED: Station 001e.65cf.9ca8 Authentication
failed
[code]....
View 1 Replies
View Related
Oct 5, 2011
LMS 4.0.1 installed on Windows Server 2008 R2 Standard with SP1. Created Inventory collection job, but couple of hours later, it is failed with all devices Not Attempted. Increased SNMP timeout on 10 sec, started again for only 1 device - collection failed again. I am attaching pdshow and ICServer file.
View 6 Replies
View Related
May 8, 2013
We have a AP1252AG-A-K9. Everytime we load it up this is what we get (see below). I tried resetting the system ("mode" way) and it did not fix the issue. I tried to reinstall the IOS and it fixes everything up and the AP will work as normal but everytime I reset the modem I will get an error message below. [code]
View 5 Replies
View Related
Mar 11, 2013
I been having trouble with my pc ... it looks like it wants to load the page and takes forever and then it says DNS lookup failed ... sometimes it loads but I have to keep trying until it does load.. It's a Windows XP
View 9 Replies
View Related
Nov 11, 2011
There are 3 newly installed Cat4506-E.SSH and SNMPv3 access are verificated. Devices are managable in every way only the inventory is missing.If I try to collect manually then they fail but I can't figure it out why.
View 2 Replies
View Related
Jul 24, 2011
I'm currently in the process of the setting up a new wireless network and I want to test out our 7925 phones on it. When I try uploading the certificate to the phone it fails and I find the following error in the trace logs
[code]...
I created this certificate using using Windows Server 2003 and it is 2048 bits. This certificate works fine with my laptop but I'm unable to upload it to the phone. The app load currently on the phone is CP7925-MFG-D.8.LOADS. Are there any specific guidelines out there when creating a certificate for a Cisco 7925 phone?
View 2 Replies
View Related
Apr 18, 2013
i try to install n1k VSM on Cisco UCS server(4Gb memory free).Due installation i got messgae-An error was received from the ESX host while powering on VM Nexus1000V-VSM-PDC.Failed to power on VM.Could not power on VM : Admission check failed for memory resource See the VMware ESX Resource Management Guide for information on resource management settings.
Group vm.1014695: Invalid memory allocation parameters for VM vmm0:Nexus1000V-VSM-PDC. (min: 524288, max: -1, minLimit: -1, shares: -3, units: pages)
Group vm.1014695: Cannot admit VM: Memory admission check failed. Requested reservation: 534234 pages
View 1 Replies
View Related
Oct 16, 2012
My client is upgrading from anyconnect 2.5.2014 to 3.1.00495. The ASA is running ASA 5520 version 8.2(5)33 and is in an active/standby failover pair.when trying to push out the new 3.1 from the pair to windows 7 and XP machines, he gets the error "Failed to get configuration from secure gateway. Contact your system administrator". When he tries to push 2.5.2014 and 2.5.6005 out from the pair this works fine.When pushing the 3.1 out from a stand-alone test ASA 5520 it works fine.
View 2 Replies
View Related
Apr 28, 2012
Although, ACS states its installed, after going through the startup. However when I do show application nothing comes up. When I do a application start acs, %Application failed to start.
View 7 Replies
View Related
Feb 27, 2012
In my head office we have Cisco 3845 router.in the router we put the show log command the below error is came..
What is the error??why the error came??
25024684: Feb 29 10:33:13.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024685: Feb 29 10:33:33.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024686: Feb 29 10:33:53.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024687: Feb 29 10:34:13.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
View 2 Replies
View Related
Oct 30, 2012
I have a issue with our ASA firewall. I have a firewall which has inside, outside and DMZ interface. I have VPN clients that connect correctly and can acces the internal network. However for the profiles I have setup to connect via VPN to the DMZ network fails with the following messages.
ASA-6-110003: Routing failed to locate next hop
&
ASA-6-302014: Teardown TCP connection......No valid adjacency
I have connections to the DMZ which aren't VPN but are via the outside and internal interfaces with no problem.
The route table has a route to that network, and I have a nat in place
View 12 Replies
View Related
Sep 26, 2012
I have been locked out of using my VPN over the past week because of the error "Failed to Load Preferences". Whenever I open the cisco anyconnect and select the current selection or enter in a new connection I get that error. I have tried reinstalling, deleting out the cisco folder from my user account, and running cisco through the web that gives me the error "Web-based installation was unsuccessful. If you wish to install the CIsco Anyconnect VPN Client, you may download an installer package."
View 5 Replies
View Related
Aug 3, 2011
Im having this error on the 7609, but for other policy its working.
Code...
View 3 Replies
View Related
May 8, 2013
I have cisco WLC 5508 on the HQ, now I have another site in different subnet I tried to put AP on it and configure a DHCP pool with option 43 but the AP failed to register the WLC on the HQ.
View 13 Replies
View Related
Mar 31, 2009
I am trying to install a digi cert on a 7921 and I get the message on import of "certificate verification failed".as there does not seem to be much documentation with the above error message.
View 2 Replies
View Related
Jun 5, 2013
I've just had to rebuild my ACS appliance with new hardrives but I am unable to register the devices to each I get a system error. I thought it may have had something to do with the rebuilt device not being joined tothe domain but it has now been joined albeit using a different ad account, but still cannot register to primary.
View 11 Replies
View Related
Feb 18, 2013
yesterday I have my AIR-AP1252AG-C-K9 failed, I cannot access it via IP and I also cannot find it via CDP. when i connect the power, the ethernet and radio lights go to red and status light goes orange/amber immediately and keep this all the time.if i try to hold the mode button from when i connect the power, all three lights keep off and never be on unless you leave the mode button along and re-connect the power.and there is NO output from the sierial console.
View 3 Replies
View Related
