We have a AP1252AG-A-K9. Everytime we load it up this is what we get (see below). I tried resetting the system ("mode" way) and it did not fix the issue. I tried to reinstall the IOS and it fixes everything up and the AP will work as normal but everytime I reset the modem I will get an error message below. [code]
View 5 Repliesyesterday I have my AIR-AP1252AG-C-K9 failed, I cannot access it via IP and I also cannot find it via CDP. when i connect the power, the ethernet and radio lights go to red and status light goes orange/amber immediately and keep this all the time.if i try to hold the mode button from when i connect the power, all three lights keep off and never be on unless you leave the mode button along and re-connect the power.and there is NO output from the sierial console.
View 3 Replies View RelatedI have three of these AP that quit associating with the controller after a power loss. I have dismounted one of them and it has an Amber light on ethernet LED and Green Light on radio LED and off on status.It does not respond to reset and nothing happen when i console into it. What might have happened to this AP? It's barely two years. I have tried different power injectors and direct power and still behaves the same way.
View 3 Replies View RelatedHow many VLANs can be managed with the AIR-AP1252AG-E-K9 APs ? My customer wants to manage 4 VLANs, data, voice, guest and another.
View 2 Replies View RelatedWe have 80 LAP1252AG and WLC 4404. We plan to upgrade our WLC 4404 to WLC 5760 but not sure if our current APs will work with the new WLC 5760.
View 1 Replies View RelatedWe have an AP located on a German site which is supposed to connect to a WLC which is in Germany as well. Our network however is spread to France as well where another WLC is located. Now, the AP can not be convinced to connect to the German WLC. Despite our efforts (e.g. manuel IP configuration, reset to factory defaults) we don't manage to bring that AP to the German network - this is by the way the only AP, all other approx. 200 work just fine.
View 6 Replies View RelatedI would like to know AIR-AP1252AG-A-K9 (Autonomous AP) can be changed to LWAPP AP by changing IOS image??
View 1 Replies View RelatedHow to be able to get AP1252AG-E-K9 running against Microsoft Windows Server 2008 R2 IAS.I am getting these errors:
RADIUS/DECODE: convert VSA string; FAIL
RADIUS/DECODE: cisco VSA type 1; FAILRADIUS/DECODE: VSA; FAILRADIUS/DECODE: decoder; FAIL
RADIUS/DECODE: attribute Vendor-Specific; FAIL
RADIUS/DECODE: parse response op decode; FAILRADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
In the near future I plan on updating all of my firewalls to 8.4, currently we're on a mix of 8.0 and 8.2. I've heard that if your equipment is on 8.2 there's an auto-conversion feature when upgrading to 8.3. However, I do not want to rely on that and am trying my hand at re-writing the NAT and ACLs myself. Attached is my pre 8.3 ASA 5510 config (santized) and a document that shows the particular sections pre 8.3 and what I think they should be after the upgrade.
View 1 Replies View RelatedI have over 20 units doing the same thing and it seems to be a software isssue but i dont see any bugs or posts on it. This is only on 2960S switches and not 2960 or 2960G units.
If i use the password reset feature to break the units into rom and then type "boot" instead of power cycling the unit, they will fail MBIST post tests. If the unit is power cycled or left to boot normally on its own, there is no issues and all post tests pass. I know MBIST is Memory Built In Self Test and was thinking maybe breaking the unit into rom disrupts those memory tests for some reason. I tried the following software and got the same results with all of the images:
122-55.SE2
122-55.SE
122-53.SE2
122-53.SE1
Logs attached are from the same switch, one with password reset procedure used and while left to boot on its own.
A lightening strike hit us recently (last week) and fried electronics in the house. The next morning we didn't have internet on either our PC or Apple laptop. The modem wasn't doing its blinky green light dance. I used a multi-meter; the power supply was dead. I replaced it. It did its blinky dance. I turned everything on in order; turn everything off, turn the modem on and wait, turn the router on and wait, and turn on the PC and laptop. The good news was, the laptop got the internet, albeit much more slowly and intermittently than it used to. The PC got nothing. I've fumbled around with this for a week and can't fix it. I'm not sure if what's wrong is the router, modem, or something specific to the PC. Time Warner reported the internet is getting to my location (I called). They said the router was the problem and, consequently, not their problem. I tried connecting the laptop to the modem directly, leaving the router and PC unconnected. This works (I get the internet on the laptop, still). I tried connecting the PC to the modem and leaving the laptop and router unconnected. This *doesn't* work (I get no internet on the PC). Device manager shows that my ethernet card works. I tried sending a test packet to the modem. This also worked. Here's my ipconfig /all Microsoft Windows [Version 6.1.7600]
View 2 Replies View RelatedI work at a public library, and our wireless network is controlled with a captive portal. I am using the app Tasker on my Verizon Galaxy Nexus (Android 4.0.3) to do things like automatically silence the phone when it connects to the wireless network. What I'm hoping to do is get it to also automatically authenticate with the captive portal. I know this is possible on a PC, but I'm not sure how to implement it with my phone. Takser allows for using HTTP GET of HTTP POST. With GET I have fields for "Server:Port", "Path", "Attributes", "Timeout", "Mime Type", and "Output File". For POST I have "Server:Port", "Path", "Data", "Timeout", "Content Type", and "Output File". Here is documentation about these two methods:
Quote:HTTP Get Send an HTTP GET request to a webserver.The response code is stored in %HTTPR. A response code of -1 indicates a problem making the request. Any returned data is stored in the variable %HTTPD if the content type is text-based (max 4K).
Example: running a script
Server:Port: [URL] [no port specified, use port 80]
Path: cgi-bin/palpable.pl
Attributes: [must be separated by newlines, no spaces please]
colour=pink
scent=rosy
[code]....
I upgraded my computer with a new graphics card and power supply. When I turned it on everything ran fine except for the internet. I either get a connection with 1 bar, a connection but no internet acess, or no internet at all. Did I damage something on the motherboard that could cause this?
View 11 Replies View RelatedI have an ASA 5505 on a job. It is a smaller business that would have done better with an RV082, but they have what they have. It is running firmware 8.4. The client needed ports forwarded for their FTP server. The port range in this config is tcp 43333-43339. The FTP server ip is 192.168.1.2. [Code] ......
View 8 Replies View RelatedI have a C2960-24TT-L Switch with the following problem:When the Power Cord is plugged in the Switch, all switch indicator LEDs go on very briefly. Then SYST LED blinks very briefly, goes on steady and remains at this state without any indication at the console.Tried the reset by holding the MODE button while plugging in power but I still get no indication at the console. All is fine with console, meaning that if I take out the cable and plug it in another switch, then I see all that there is there to be seen.My question: Is the switch beyond repair or is there something that can be done to get the switch to run POST and boot at rommon so that I can reload SW and configs?
View 3 Replies View RelatedLost my access points to controller. Not sure if it was related to upgrade from 7.1 to 7.2, or something else.
The console log on APs shows;
*Mar 1 00:01:09.394: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 1 10:24:23.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 142.100.64.8 peer_port: 5246
*Jan 1 10:24:23.424: %DTLS-5-ALERT: Received FATAL : Certificate unknown alert from 142.100.64.8
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Bad certificate alert received from peer.
*Jan 1 10:24:23.424: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 142.100.64.8:5246
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
All 3500/3600 APs, had been in production for months.
working config with least amount of code for:
IOS post 8.3
Subnet: 192.168.1.0 /24
Static NAT (from any source) to server 192.168.1.100 and allow the same incoming connections on outside interface
Ports:
TCP 20,21
TCP 80
UDP 50000-50020
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies View RelatedUsing AnyConnect Secure Mobility Client, logging into ASA5540. After I put my credentials in, I get the banner message (from group policies). After I accept that, I get another pop message stating:It looks like a pre-set message. Where can I disable and/or edit this message?
View 4 Replies View RelatedI have a Cisco CBS3020-HPQ chassis switch running IOS 12.2.(25r)SEF3. One of the ports is in "disabled" state but when I try to unshut it, it doesn't work, the switch logs shows the following event:
%PLATFORM_ENV-3-LOOPBACK_PORT_POST_ERR: Gi0/1 can't be brought up because it failed POST in Loopback test
how do I resolve this, the port is unusable since I can not get it out "disabled" state.
I pulled a brand new Cisco 3850 Switch out of the box yesterday. Following the Quick Start Guide, I put in the power module, powered it on, and waited for it to complete POST. Then, I plugged in an Ethernet cable between a laptop and the switch on a port in the front, and went to the web interface at https://10.0.0.1. I got to the Express Setup, and attempted to change the IP address of the switch to an IP on my LAN, along with other options. When clicking submit, it didn't appear to take. Upon refreshing in the Express Setup, the IP config was blank, so I once again configured it. This time clicking submit brought up a message that it was changing the IP address. I waited for it to finish, and when it looked done, I powered the switch off and took it to a different room to hook it up to the LAN for further configuration.
When plugging in the power at that point, the switch starts through the normal light process (System LED blinks green slowly), and then eventually the System LED blinks green very fast and never stops. It doesn't get to the point of having the system loaded and ready to log into. There's no amber lights, just the System LED flashing green fast. On the back, the Power module and all bay lights are green, and the Console light is green, but the Management port light is off.
I've tried using the reset button on the back of the switch two different times to reset it to default configuration, thinking I hosed it somehow, but it never goes past the fast blinking System LED.
I have 2 - WS-C2960-24TT-L switches. Both are experiencing the same issue. Upon booting them up, all lights flash on the mode indicator panel, then it goes directly to a solid green "SYST" light. Nothing registers across the console cable. I have tried different baud rates, cables and computers. None of the ports come up regardless of how long either switch is powered on. Holding the Mode button during boot up produces the same result, nothing. Sounds like they are dead, however, I thought this would be the place to go for ideas. Can I revive these switches?
View 3 Replies View RelatedI am trying to configure a 3750G that has been sitting on the shelf for several months and am getting the following error -
% Error: Unable to create flash:/microcode_update% Error: It must not already exist
Normally, getting an error during POST isnt a good thing. My first thought was that flash was corrupted or flagged RO somehow. I did fsck flash: with no change. I next tried fsck /test flash:. It tested 77 blocks and performed 0 erasures. It had been running for about 15 minutes with no problems reported so far. Multiple reboots of the switch still report the same error.
I have reviewed the history of what I have done on this switch and finally think I found the problem. I noticed a microcode_update directory that I am not used to see on a 3750. Deleted the directory using the rmdir command and rebooted the switch. On reboot, I noticed that a front_end/ directory was listed as being created as well as fe_type_1 and fe_type_2 were created. The switch now boots up without any errors.
I'm learning about iptables, but I don't fully understand the chains of NAT table (prerouting, postrouting and output).I'm specially in doubt about prerouting and postrouting. As far as I know, DNAT can be made with prerouting and SNAT can be made with postrouting, so I think prerouting is for input and postrouting is for output, but the material I'm reading (and another sources) are not clear.
View 4 Replies View RelatedUTMajoracquisition failed to run in LMS 4.0.1..
Troubleshooting done
1) Started the UTMajorAcuisition process manually using pdexec: It again fails to run
2) Renamed to ut.properties.orig to ut.properties and tried to restart the process .. IT again fails to run.
I have a cisco 887 router and I have tested on two different DSL line. The first line it worked fine with while the other noe is not. both line on same exchange and establishing the ppp session with same BRAS. The debug seems that there Establishing phase failed, but my question here is how our BRAS will faied the establishing from on line while from other landline is working fine.
=============================================================
CISCO ROUTER Configuration
=======================
interface ATM0/1/0no ip addressno ip mroute-cacheno atm ilmi-keepalivedsl operating-mode autopvc 8/35encapsulation aal5mux ppp dialerdialer pool-member !interface Dialer1ip address negotiatedip nat outsideip virtual-reassemblyencapsulation pppdialer pool 1ppp chap hostname companyxppp chap password abcda123ppp pap sent-username companyx password abcda123
===========================================
when I did ppp negotiation debug the below messages i got:
============================================
Mar 16 13:19:18.103: Vi2 PPP: Phase is DOWN
Mar 16 13:19:19.103: PPP: Alloc Context [85DEC77C]
Mar 16 13:19:19.103: ppp28 PPP: Phase is ESTABLISHING
Mar 16 13:19:19.103: Vi2 PPP: Using dialer call direction
Mar 16 13:19:19.103: Vi2 PPP: Treating connection as a callout
Mar 16 13:19:19.103: Vi2 PPP: Session handle[700001C] Session id[28]
[code]....
I can't inventory a 4507R + E / SUP7E Version 15.1.1 SG with the last version of LMS 4.2.1. Next, the extract of IC_Server.log.
[code]....
I have installed Ciscoworks LMS 3.2 0n windows server 2003 enterprise edition. I have issue with Campus Manager while accessing any thing in Campus Manager it is giving following error.
"Error in loading properties from the server" "Can not contact to ANI server" Status of ANIServer process is Failed to run
I tried to reinitialize Campus Manager Database still it is showing same issue.
Installed Campus manager version 5.2.1 check attached file for ANI log
[code]....
Red error what is the reason? Only appears in the window 2003 server.
I have issue with the ANI Server process, which fails to start. The LMS version is 3.2. It's recently installed, with just one device added to the database so far. I've read some similar cases in the forum, but I'm starting a new thread since it could be a different issue which causes the problem.Please, find attached ani.log, ANIServer.log, the output of the pdshow command and ANIServer.properties files. I doubt that the last one might be corrupted for some reason.
View 4 Replies View RelatedFor quite some time now, we have been experiencing an issue with the Cisco VPN client that will make the client completely unusable. I have noticed that when a specific feature of Symantec Endpoint Protection is enabled, it will (about 25% of the time) cause the following errors to appear when attempting to connect anywhere with the Cisco VPN client. Once this error happens once, the VPN client then becomes useless.
Error #1
Reason 414: Failed to establish a TCP connection
Error #2
Reason 440: Driver Failure
Error #3
Reason 442: Failed to enable virtual adapter
It seems that fixing one error will cause the other error to come up.I have tried reinstalling the client with the same version and older versions and the issue still comes up. All users in the company are using Windows 7 64-bit with SP1 installed.The oddest thing about this is that all employees in the company have the same antivirus with the same features enabled, however, it only happens to a small percentage of employees.
I am facing a failed issue when restoring the WCS Database. Below is the error i get, does any one out there facing it before?
#######################################
[root@egwgwcs WCS7.0.220.0]# ./Restore
Please enter the full path of the backup file name: /opt/WCS7.0.220.0/Backup_File/WCS_Aug2012.nmsbackup
Untaring the backup file...
Failed to untar backup file. Exception: invalid stored block lengths
Restore database failed.
#######################################
I have Cisco Works LMS 4.0 on Win 2K8 64 bits on VMware EXs. I am facing issue with reference to Inventory Collection, my 10% devices (including Routers & Switches) Inventory collection is failed and give me error (Device sensed, but collection failed). I increase the SNMP timeout 10 sec, 30 sec, 60 sec and even 100 sec the result be the same.
View 1 Replies View Related