Broadband :: PC Can't Connect To Internet Post-Lightening
Aug 8, 2012
A lightening strike hit us recently (last week) and fried electronics in the house. The next morning we didn't have internet on either our PC or Apple laptop. The modem wasn't doing its blinky green light dance. I used a multi-meter; the power supply was dead. I replaced it. It did its blinky dance. I turned everything on in order; turn everything off, turn the modem on and wait, turn the router on and wait, and turn on the PC and laptop. The good news was, the laptop got the internet, albeit much more slowly and intermittently than it used to. The PC got nothing. I've fumbled around with this for a week and can't fix it. I'm not sure if what's wrong is the router, modem, or something specific to the PC. Time Warner reported the internet is getting to my location (I called). They said the router was the problem and, consequently, not their problem. I tried connecting the laptop to the modem directly, leaving the router and PC unconnected. This works (I get the internet on the laptop, still). I tried connecting the PC to the modem and leaving the laptop and router unconnected. This *doesn't* work (I get no internet on the PC). Device manager shows that my ethernet card works. I tried sending a test packet to the modem. This also worked. Here's my ipconfig /all Microsoft Windows [Version 6.1.7600]
View 2 Replies
ADVERTISEMENT
Nov 18, 2012
I have a laptop and a computer. The laptop works fine and so does the computer. My computer says I'm connected to the internet, But Whenever I try to get on the internet (GoogleChrome, Mozzila Firefox, Internet Explorer) It says I'm not connected to the internet. And I checked everything and it says I'm connected. I just can't get on the internet pages. Not even messenger.
View 1 Replies
View Related
Jul 14, 2011
I recently reformatted and restored the original os on my Gateway MX6920 which is windows xp media center edition. Before and after restoring the original os, however, I still have not been able to connect to the internet through the onboard lan that doesn't seem to be active or even be seen by the computer. How should I fix this? Is there a possibility that the internal lan was disabled mechanically? Or would I have to get a pci lan card? as I have been trying to get this computer to work properly for the last 4 weeks. Also, before I restored the os, I put a pci lan card in but it still would not recognize that there was an internet connection when I would connect it to an active ethernet connection. I'm worried that I still will not be able to connect when I get a new pci lan card because of unknown reasons that I have been trying to figure out for quite some time now.
View 2 Replies
View Related
Mar 4, 2012
I am trying to connect my laptop to the Internet and it isn't working. I have high speed broad band both modem and a nexxt router. My laptop does not recognize that there is a wireless network in the area. When I connect the cable directly from the router to my laptop jack it does not recognize it has an Internet connection. I have tried running windows network connection setup wizards but no luck. There is another computer on the network that connects with the Internet flawlessly. I also downloaded a new driver but that did not work. I have a windows seven 32 bit notepad.
View 1 Replies
View Related
May 3, 2012
However I cannot connect to the internet, the following message appears. The system cannot up date the telephone book file error 624. I am not connected to a telephone line for my system, as I use a modem USB, which is working ok.
View 1 Replies
View Related
May 1, 2011
i have the internet connection but it wont connect. and theres no file button to select to click to work offline the whole page is blank
View 2 Replies
View Related
Sep 9, 2011
I cant connect to internet but other user can. We use the same laptop but my internet connection was cut off whereas my son's internet connection on the same computer is working fine. I have used cable as well with no success. Obviously there is nothing wrong with the router or cable or wireless but there must be something wrong with my user settings. My son is using the same computer and can connect fine to internet as another user.
View 2 Replies
View Related
Aug 15, 2011
diagnosis is indicating server is connected but internet is not connected
View 1 Replies
View Related
Jan 23, 2011
reloaded xp. dont seem to have internet drivers. down loaded new drivers and seem to do no good. still unable to connect to internet.
View 1 Replies
View Related
Jan 22, 2011
My internet connect sometimes and other time is won't do nothing at all it picking up the network just won't pull up anything. I just flush my dns and still no luck.
View 1 Replies
View Related
Oct 18, 2011
There are currently 6 laptops in my household.4 windows (1 vista, 1 xp2002 pro, 2 windows 7) and 2 linux (both ubuntu). Night before last, without warning, all 6 stopped connecting through the wireless router. I took the router out of the mix, and now only the linux laptops can connect to the internet via ethernet cable. comcast support is useless.any ideas what could be happening here? Only 1 of the linux and 2 of the windows laptops were connected at the time this occurred.
View 7 Replies
View Related
Jul 4, 2011
Ethernet driver or wireless undetected have a port to plug ethernet cord into on computer
View 1 Replies
View Related
Dec 28, 2011
It's not on one device, and it doesn't matter if you are connected wirelessly or by cable. It also doesn't matter what internet browser you use. I would guesstimate that every 5-15 mins the dsl broadband just gives and all internet goes down for probably 1-3 mins at a time.I honestly have no idea. I'm using a 2Wire, just what AT&T gave me. I'm guessing it's either the dsl filter, or the actually router itself, i'm just not sure how to go about troubleshooting and figuring out the root of the problem.
View 1 Replies
View Related
Jul 6, 2012
My xp laptop does not connect to the internet using USB broadband after deletion of the dns changer virus (although still shows a connection) , however still connects using LAN or wireless. The usb modem works on other xp computers.Tried ipconfig/dnsflush, cfs /runnow/ uninstall and reinstall modem and usb ports.
View 4 Replies
View Related
Oct 24, 2011
I am using USB internet connection. I am trying to connect internet, it shows all the signal but connect button is grayed out.
View 1 Replies
View Related
Jul 1, 2011
I just need a usb dongle to connect my acer n30 handheld to my internet
View 2 Replies
View Related
May 24, 2012
Firefox, Safari, SeaMonkey nor Chrome can´t connect internet even I´ve got internet connection
View 5 Replies
View Related
Jan 2, 2013
why my computer cannot connect to wifi but can only connect to ethernet and broadband only?
View 2 Replies
View Related
Dec 19, 2011
My computer was recently infected with the XP Antivirus 2012 rogue virus. I believe that it has been removed from my computer, but I am unable to connect to the internet. I am unable to obtain an IP address. The IP address is 00000 and the Submask is 0000. My operating system is Windows XP and I am using a High speed cable connection
View 5 Replies
View Related
Feb 4, 2013
I am trying to connect to the internet using the PPPoE feature of the router but the router configuration is not successful. Says something like "WAN connection not successful". I have supplied the correct username and password. The connection is ok in my laptop if i directly connect my laptop to the Ethernet port of the modem without the router. Is this a sharing problem from the ISP?
View 10 Replies
View Related
Feb 22, 2011
ok so my moms computer (compaq fs7600) had vista an it went nuts so i wiped it an installed xp pro. Everything went fine but now it wont connect to the internet =/. I have a Belkin Wireless router and an Arris high speed modem from Brighthouse. When i checked the cmd prompt it said that the media is disconnected an network connections said that it was unplugged, but everything is plugged in
View 3 Replies
View Related
Apr 1, 2013
i m getting error 769 when i m trying 2 connect my broadband.. when i searched for network adapter 2 make it enabled in d device manager duologue box.
View 1 Replies
View Related
May 8, 2013
We have a AP1252AG-A-K9. Everytime we load it up this is what we get (see below). I tried resetting the system ("mode" way) and it did not fix the issue. I tried to reinstall the IOS and it fixes everything up and the AP will work as normal but everytime I reset the modem I will get an error message below. [code]
View 5 Replies
View Related
Mar 16, 2012
I work at a public library, and our wireless network is controlled with a captive portal. I am using the app Tasker on my Verizon Galaxy Nexus (Android 4.0.3) to do things like automatically silence the phone when it connects to the wireless network. What I'm hoping to do is get it to also automatically authenticate with the captive portal. I know this is possible on a PC, but I'm not sure how to implement it with my phone. Takser allows for using HTTP GET of HTTP POST. With GET I have fields for "Server:Port", "Path", "Attributes", "Timeout", "Mime Type", and "Output File". For POST I have "Server:Port", "Path", "Data", "Timeout", "Content Type", and "Output File". Here is documentation about these two methods:
Quote:HTTP Get Send an HTTP GET request to a webserver.The response code is stored in %HTTPR. A response code of -1 indicates a problem making the request. Any returned data is stored in the variable %HTTPD if the content type is text-based (max 4K).
Example: running a script
Server:Port: [URL] [no port specified, use port 80]
Path: cgi-bin/palpable.pl
Attributes: [must be separated by newlines, no spaces please]
colour=pink
scent=rosy
[code]....
View 17 Replies
View Related
Mar 8, 2012
I upgraded my computer with a new graphics card and power supply. When I turned it on everything ran fine except for the internet. I either get a connection with 1 bar, a connection but no internet acess, or no internet at all. Did I damage something on the motherboard that could cause this?
View 11 Replies
View Related
Aug 30, 2012
In the near future I plan on updating all of my firewalls to 8.4, currently we're on a mix of 8.0 and 8.2. I've heard that if your equipment is on 8.2 there's an auto-conversion feature when upgrading to 8.3. However, I do not want to rely on that and am trying my hand at re-writing the NAT and ACLs myself. Attached is my pre 8.3 ASA 5510 config (santized) and a document that shows the particular sections pre 8.3 and what I think they should be after the upgrade.
View 1 Replies
View Related
May 8, 2011
I have over 20 units doing the same thing and it seems to be a software isssue but i dont see any bugs or posts on it. This is only on 2960S switches and not 2960 or 2960G units.
Â
If i use the password reset feature to break the units into rom and then type "boot" instead of power cycling the unit, they will fail MBIST post tests. If the unit is power cycled or left to boot normally on its own, there is no issues and all post tests pass. I know MBIST is Memory Built In Self Test and was thinking maybe breaking the unit into rom disrupts those memory tests for some reason. I tried the following software and got the same results with all of the images:
122-55.SE2
122-55.SE
122-53.SE2
122-53.SE1
Â
Logs attached are from the same switch, one with password reset procedure used and while left to boot on its own.Â
View 11 Replies
View Related
Jun 1, 2011
I have an ASA 5505 on a job. It is a smaller business that would have done better with an RV082, but they have what they have. It is running firmware 8.4. The client needed ports forwarded for their FTP server. The port range in this config is tcp 43333-43339. The FTP server ip is 192.168.1.2. [Code] ......
View 8 Replies
View Related
Apr 23, 2013
I have a C2960-24TT-L Switch with the following problem:When the Power Cord is plugged in the Switch, all switch indicator LEDs go on very briefly. Then SYST LED blinks very briefly, goes on steady and remains at this state without any indication at the console.Tried the reset by holding the MODE button while plugging in power but I still get no indication at the console. All is fine with console, meaning that if I take out the cable and plug it in another switch, then I see all that there is there to be seen.My question: Is the switch beyond repair or is there something that can be done to get the switch to run POST and boot at rommon so that I can reload SW and configs?
View 3 Replies
View Related
Feb 8, 2013
Lost my access points to controller. Not sure if it was related to upgrade from 7.1 to 7.2, or something else.
Â
The console log on APs shows;Â
Â
*Mar 1 00:01:09.394: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 1 10:24:23.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 142.100.64.8 peer_port: 5246
*Jan 1 10:24:23.424: %DTLS-5-ALERT: Received FATAL : Certificate unknown alert from 142.100.64.8
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Bad certificate alert received from peer.
*Jan 1 10:24:23.424: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 142.100.64.8:5246
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
 Â
All 3500/3600 APs, had been in production for months.
View 1 Replies
View Related
Mar 17, 2012
working config with least amount of code for:
Â
IOS post 8.3
Subnet: 192.168.1.0 /24
Â
Static NAT (from any source) to server 192.168.1.100 and allow the same incoming connections on outside interface
Â
Ports:
TCP 20,21
TCP 80
UDP 50000-50020
View 1 Replies
View Related
Jul 27, 2011
Using AnyConnect Secure Mobility Client, logging into ASA5540. After I put my credentials in, I get the banner message (from group policies). After I accept that, I get another pop message stating:It looks like a pre-set message. Where can I disable and/or edit this message?
View 4 Replies
View Related
Jun 5, 2012
I have a Cisco CBS3020-HPQ chassis switch running IOS 12.2.(25r)SEF3. One of the ports is in "disabled" state but when I try to unshut it, it doesn't work, the switch logs shows the following event:
Â
%PLATFORM_ENV-3-LOOPBACK_PORT_POST_ERR: Gi0/1 can't be brought up because it failed POST in Loopback test
Â
how do I resolve this, the port is unusable since I can not get it out "disabled" state.
View 6 Replies
View Related