Cisco Wireless :: Change Country Code For AIR-AP1252AG-E-K9
Jul 23, 2012
We have an AP located on a German site which is supposed to connect to a WLC which is in Germany as well. Our network however is spread to France as well where another WLC is located. Now, the AP can not be convinced to connect to the German WLC. Despite our efforts (e.g. manuel IP configuration, reset to factory defaults) we don't manage to bring that AP to the German network - this is by the way the only AP, all other approx. 200 work just fine.
I am trying to install SSL VPN on our 1941 router. When i try to send a CSR for signing the site complains about the country code not being correct. How can i change the contry code in Cisco IOS Version 15.0(1r)M9 ?
It is also complaining about the domainname, but the thing right now is the contry code.
I have a WLC 5008 running with 40 AIR-LAP1042N-E-K9 and country code BE (Belgium) configured.I also have some AIR-AP1142N-C-K9 which I converted to CAPWAP OS.Unfortunattely only 1 of the 2 radio interfaces is working because of regulatory reasons.(the AP's are -C models which stands for China - although they were bought in Belgium too).I tried to activate the country codes for BE and China, but the WLC won't accept both.Is there a way to get the 2nd radio interface working ?
We have cisco 2504 controller and 1200 series access point.These are in India and country code is IN.When access point joins the controller , then in wireless>advanced , i see the two country code is already configured these are Sri Lnaka(LK) and Singpore (SG).I have disabled the radios and changed the country code to IN but after doing that Access point is not joining the controller and giving the duplicate error.
Then i have again set the country code to IN,LK and SG.I am able to see the LK and SG but In is not showing in drop down list.
I have a WRT160N that I've been using with my HDTV for months. Now I want to connect a BluRay player to it, but the setup requires me to enter a security code, and the one I had for the router doesn't work. Can I change the number, or at least double-check the number I do have?
I have three of these AP that quit associating with the controller after a power loss. I have dismounted one of them and it has an Amber light on ethernet LED and Green Light on radio LED and off on status.It does not respond to reset and nothing happen when i console into it. What might have happened to this AP? It's barely two years. I have tried different power injectors and direct power and still behaves the same way.
yesterday I have my AIR-AP1252AG-C-K9 failed, I cannot access it via IP and I also cannot find it via CDP. when i connect the power, the ethernet and radio lights go to red and status light goes orange/amber immediately and keep this all the time.if i try to hold the mode button from when i connect the power, all three lights keep off and never be on unless you leave the mode button along and re-connect the power.and there is NO output from the sierial console.
I have been searching through the cisco docs for a while and i just cant seem to find this info. Can I run aironet 1600's with my wism running 7.0.116? Also, could I run my 1130 series ap's with a wism2? Basically, what is the minimum code level for a lightweight 1600, and what is the maximum code level for a lightweight 1130?
Currently my solution consist of two 5508 controllers and several non-mesh and few mesh AP (2600) running in flexconnect mode in one single site in europe. Everything is going fine. However there is going to be a new site in Canada. I found some documentation saying that multiple country code is not available for mesh ap. Mesh ap are not going to join controller if multiple country code configured . but all this documentation is regarding version 7.2 and older. Im running version 7.4.100.0 and on configuration guide I don't find anything related to that.
I bought a v1. wusb600n for win XP sp3, recently for no apparent reason, it became stuck in country region #2 (ch 36 to 64) when i use WZC or even netstumbler to view networks. I have tried uninstall/reinstall of driver, tried using ralink's driver and even another usb600n, but the problem remains.
Checking the INF files shows that all the drivers are trying to install as region #0 (36-64 + 149-165) but they are always showing as region #2
We have a AP1252AG-A-K9. Everytime we load it up this is what we get (see below). I tried resetting the system ("mode" way) and it did not fix the issue. I tried to reinstall the IOS and it fixes everything up and the AP will work as normal but everytime I reset the modem I will get an error message below. [code]
How to be able to get AP1252AG-E-K9 running against Microsoft Windows Server 2008 R2 IAS.I am getting these errors:
RADIUS/DECODE: convert VSA string; FAIL RADIUS/DECODE: cisco VSA type 1; FAILRADIUS/DECODE: VSA; FAILRADIUS/DECODE: decoder; FAIL RADIUS/DECODE: attribute Vendor-Specific; FAIL RADIUS/DECODE: parse response op decode; FAILRADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
I have a ASA 5510 device. I have been asked to block Ip range for India from accessing set of servers. Total Subnets: 34,675,968.I really don't want to create a two mile long access list with all these subnets.
I have a list of email addresses, people who have subscribed to a free electronic newsletter. The email address is all the information we have about each subscriber.A satellite office is going to begin handling print and electronic subscriptions for subscribers in Peru. Is there any way to determine which of these email addresses are from Peru?
Iam trying to add servers to Tor (torproject.org) to remove country restrictions on videos from different websites such as bbc.com and i don't know how to do it. I got the server but I don't know what do do next?
I am planning to upgrade the WLC code and I have about 133 RAPs/MAPs/1131 APs that already joined the WLC. Will I have a problem with my MAPs when the WLC starts upgrading the code. Some MAPs will have 3 hops to connect to a RAP.
Our company has a customer with a Cisco 4402 WLC and a code version of 4.2.130.0 . The customer wants to upgrade the code to 7.0.230.0. Is there any flash size requirement when upgrading to 7.0.230.0? (upgrade train: 4.2.130.0 ----> 4.2.209.0 ----> 7.0.230.0), How can I find the flash size?
I need to convert some 1142 APs to lightweight mode. They will connect to controllers running 7.3.101.0. I noticed there's two options of Lightweight IOS code available c1140-k9w8-tar.152-2.JA.tar and c1140-rcvk9w8-tar.152-2.JA.tar. Whats the difference between the two versions of code?
Working on a project consolidating all controllers to a single 8500 controller with a standby. Moved an AP over to test the process and everything worked fine. Took a little longer than I thought it would, but given the design with new flexconnect abilities, the creation of AP groups well you know.
I get the AP over and one of my ssids doesnt work because the key is different, so gotta move the AP back over to resolve production issues.
Just purchased a 2504 w/15 licenses and to run 10 - 2602i AP's. Code out of the box is 7.0.222.0 but when I go the support site I see 7.2, 7.3 and 7.4 all with relatively recent dates. I found I need 7.2.110.0 at a minimum to run the AP's. All the code versions say ED, which I thought was not final release versions.
