Cisco Wireless :: 2504 Country Code Is Not Showing In Access Point
Jan 23, 2013
We have cisco 2504 controller and 1200 series access point.These are in India and country code is IN.When access point joins the controller , then in wireless>advanced , i see the two country code is already configured these are Sri Lnaka(LK) and Singpore (SG).I have disabled the radios and changed the country code to IN but after doing that Access point is not joining the controller and giving the duplicate error.
Then i have again set the country code to IN,LK and SG.I am able to see the LK and SG but In is not showing in drop down list.
Operationally everything is working fine.
View 3 Replies
ADVERTISEMENT
Jul 23, 2012
We have an AP located on a German site which is supposed to connect to a WLC which is in Germany as well. Our network however is spread to France as well where another WLC is located. Now, the AP can not be convinced to connect to the German WLC. Despite our efforts (e.g. manuel IP configuration, reset to factory defaults) we don't manage to bring that AP to the German network - this is by the way the only AP, all other approx. 200 work just fine.
View 6 Replies
View Related
Jul 6, 2011
I have a WLC 5008 running with 40 AIR-LAP1042N-E-K9 and country code BE (Belgium) configured.I also have some AIR-AP1142N-C-K9 which I converted to CAPWAP OS.Unfortunattely only 1 of the 2 radio interfaces is working because of regulatory reasons.(the AP's are -C models which stands for China - although they were bought in Belgium too).I tried to activate the country codes for BE and China, but the WLC won't accept both.Is there a way to get the 2nd radio interface working ?
View 3 Replies
View Related
Mar 24, 2013
[code]...
In the meantime my linksys supports just: 36, 40, 44, 48 which are not allowed in TW.I can't connect to my ea4300 via 5Ghz what makes me sad
View 6 Replies
View Related
May 3, 2011
I am trying to install SSL VPN on our 1941 router. When i try to send a CSR for signing the site complains about the country code not being correct. How can i change the contry code in Cisco IOS Version 15.0(1r)M9 ?
It is also complaining about the domainname, but the thing right now is the contry code.
View 3 Replies
View Related
Aug 28, 2012
i have stand alone cisco 1130g ap ,and wlc 2504. wlc 2504 support this ap or not ?
View 3 Replies
View Related
Jun 15, 2012
i have cisco CAP 3602e series access point to work with 5500 series controller with code 7.0i did not find VCI option 60 for this type of APs to configure DHCP. How I can let these APs will join the controller, i mean through which process DNS discovery methode and what about if i need to configure option 60 and 43 in dhcp for ap joining process to controllers.
View 4 Replies
View Related
Jul 27, 2012
Question about cisco 2504 wireless controller, is it support cisco 1552E outdoor access point? If NO provide me the correct series/model.
View 9 Replies
View Related
Jun 13, 2013
We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?
View 1 Replies
View Related
Sep 18, 2012
We have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
View 3 Replies
View Related
Jan 1, 2012
i have access point but no security code where do i find this?
View 1 Replies
View Related
Apr 23, 2013
Just purchased a 2504 w/15 licenses and to run 10 - 2602i AP's. Code out of the box is 7.0.222.0 but when I go the support site I see 7.2, 7.3 and 7.4 all with relatively recent dates. I found I need 7.2.110.0 at a minimum to run the AP's. All the code versions say ED, which I thought was not final release versions.
View 1 Replies
View Related
Apr 4, 2013
I am trying to setup a 2504 Wireless Controller with a few AIR-AP1262N-E-K9 Access Points. But i'm having trouble getting the access points to connect to the controller.The controller and AP's are setup at a local network at one of my customers. They are part of a quite large organization and are therefore connected to some of their other divisions in different contries via MPLS. The DHCP and DNS servers are therefore on a different subnet.I have confirmed that the Access Points do get a correct IP from the DHCP server and that i am able to ping from the controller to the AP. When looking at the controller it does not receive any join requests from the AP's. I have setup a console connection to the controller and 1 AP, so i can view debug information.Most guides mention that you can run different LWAPP commands from the CLI on the AP like show lwapp for example. But i am not able to run any of these LWAPP commands on my AP.
View 8 Replies
View Related
Aug 27, 2012
The rouge access points being detected by the 5508 WLC are not showing up on the Context Aware tab of NCS? I have a MSE 3310 installed and configured and it shows to be syncronizing with the WLC. I'm sure I am missing some part of the configuration just not sure where.
View 3 Replies
View Related
Jun 16, 2013
Cisco 2504 wlc, 1142n ap, windows radius server.
When I click on Network, the only computer that shows up is mine. If I am hardwired then everything shows up (Servers, other workstations). Is this a problem with the radius server or something on the controller?
View 2 Replies
View Related
Jan 28, 2012
I have a WAP54g set up as a repeater. It even shows in the WRT54g device list (Tomato firmware) as a WDS interface but nothing can connect to it. I have the repeater's MAC address in the AP and it's set to "Access Point + WDS" mode. I don't know what I could be doing wrong. Is it a conflict of DHCP on the AP vs static on the repeater?
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Feb 19, 2013
I have been searching through the cisco docs for a while and i just cant seem to find this info. Can I run aironet 1600's with my wism running 7.0.116? Also, could I run my 1130 series ap's with a wism2? Basically, what is the minimum code level for a lightweight 1600, and what is the maximum code level for a lightweight 1130?
View 3 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jan 23, 2013
Currently my solution consist of two 5508 controllers and several non-mesh and few mesh AP (2600) running in flexconnect mode in one single site in europe. Everything is going fine. However there is going to be a new site in Canada. I found some documentation saying that multiple country code is not available for mesh ap. Mesh ap are not going to join controller if multiple country code configured . but all this documentation is regarding version 7.2 and older. Im running version 7.4.100.0 and on configuration guide I don't find anything related to that.
View 9 Replies
View Related
Aug 31, 2009
I bought a v1. wusb600n for win XP sp3, recently for no apparent reason, it became stuck in country region #2 (ch 36 to 64) when i use WZC or even netstumbler to view networks. I have tried uninstall/reinstall of driver, tried using ralink's driver and even another usb600n, but the problem remains.
Checking the INF files shows that all the drivers are trying to install as region #0 (36-64 + 149-165) but they are always showing as region #2
View 9 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Jun 9, 2013
2504 contrller with 1042N ap's. NPS and group policy (for computers) is setup. Certificates are setup.Logging on as a domain user I can connect to the wireless network but am only getting Internet access. I can not access any domain resources.DHCP is handled by a domain controller. I can ping servers and printers, but cannot access them. Can't map a drive, add a printer or access services on the network.
View 1 Replies
View Related
Apr 3, 2012
I have 2 APs, Cisco Aironet 1040, and 2504 WLC.Is it possible to configure guest access (Guest SSID/VLAN and Corporative SSID/VLAN) without dedicated guest WLC in DMZ?
View 4 Replies
View Related
Mar 1, 2013
We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
I would like to use LDAP or ACS for authentication purpose.
View 3 Replies
View Related
Jun 4, 2012
I have setup guest access on the controller and this is not working at the moment. DHCP server setup on the controller for the Guest users. You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
View 10 Replies
View Related
