Cisco Wireless :: AIR-lap1310G-E-K9 Short Signal Length
Mar 27, 2012
I have a Cisco WISM2 installed on Cisco cat 6509, with 39 indoor (3502i) and 14 outdoor (1310G) Access point, so the problem i am facing is that, the controller recognizes all AP and they are all configured and working well, then the signal of the outdoors (1300) its broadcast in a very short length like 60 meters, and i don't understand this is likely having a problem with a controller software version or ... being at 3m, my card does not show excellent signal strength and yet with the indoor thing are Ok.
View 4 Replies
ADVERTISEMENT
Aug 27, 2012
We have other APs that associate w/o issue AIR-LAP1141N-A-K9. However our 1 1310 is having issues.. The Controller log shows:
2012-08-29 21:16:51 local0.error 172.16.10.70 ITCNJ1WC01: *spamApTask0: Aug 28 21:17:15.038: %LWAPP-3-DECRYPT_ERR5: spam_crypto.c:293 Error decrypting packet (using old key) from AP d4:8c:b5:15:3c:04 (session identifier a3ddb9c5)
2012-08-29 21:17:33 local0.error 172.16.10.70 ITCNJ1WC01: *spamApTask0: Aug 28 21:17:17.037: %LWAPP-3-DECRYPT_ERR: spam_lrad.c:3642 The system is unable to decrypt image data message; AP d4:8c:b5:15:3c:04
2012-08-29 21:17:33 local0.error 172.16.10.70 ITCNJ1WC01: *spamApTask0: Aug 28 21:17:17.037: %LWAPP-3-DECRYPT_ERR: spam_crypto.c:735 The system is unable to decrypt LWAPP packet; AP d4:8c:b5:15:3c:04
[code]....
View 3 Replies
View Related
Mar 13, 2013
I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point? My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
AP001d.4513.dd68#reloadProceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,
[code].....
View 6 Replies
View Related
Jun 12, 2011
I got a CISCO wap4410n access point and it is disconnecting uses after a shorl while. I hv to again connect them manually.
View 1 Replies
View Related
Apr 9, 2011
I bought an E4200 to replace an old buffalio Nfinity. The range on the 2.4 and 5 GHz have both been extremely short -- shorter than the old Buffalo. 1 meter from the router, I get five bars on the laptop and 3 bars on ipad. 3 meters away with direct line of sight, the laptop dips to 4 bars. Down the hallway about 4-5 meters away, the 2.4GHz is one 1 bar on laptop and ipad. the 5GHz is gone. This is two rooms away from the router in my apartment. Isn't that a bit shocking in terms of performance? A webcam that is two rooms away registers a 6% signal from the E4200.Does this sound like faulty hardware, e.g. bad antennae? I would think it is something about the build of my apartment building, but my old buffalo did MUCH better than the E4200. two Ipad bars where the E4200 has one...and in very unstable condition.
View 9 Replies
View Related
Sep 14, 2012
There is a problem with establishing an internet connection between my laptop and any wireless network, and hence the internet cannot be accessed. Though, the connection can be established locally between my laptop and the wireless network for a short while before the connection is lost locally. There is certainly no problem with my current wireless router as there are internet connections between the wireless network and other devices. Prior to using the current wireless router, I used Linksys WRT54G for internet connection until recently when there was no connection between all devices and the Linksys wireless router, so I changed my wireless router to the current one. However, the problem still persists for my laptop. I can only get access to internet when my laptop is connected to the router using ethernet cable, as well as when my laptop is connected to the main cable modem using the same cable.My laptop model is Fujitsu Lifebook S Series and my laptop is running on Windows Vista Service Pack 2 and my current wireless router is Belkin N300 Wireless N Router Model F9K1002v1.What I have done so far are that I have ensured that the DNS client and DHCP client service are enabled and that I have used the method of "/release, /dnsflush and /renew" on the command prompt.Below is the /ipconfig /all description when this laptop is connected to the cable modem using ethernet cable:
Windows IP Configuration
Host Name . . . . . . . . . . . . : FujitsuUser-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
[code]....
View 14 Replies
View Related
Apr 2, 2013
Region : USA
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.5 Build 130322 Rel.59120n
ISP :
Even before I did the latest firmware flash I couldn't select short GI under Advanced Wireless - it was simply greyed out even though WMM was enabled above it. Now after a factory reset and recreating all my settings I still can't select it.
View 2 Replies
View Related
Feb 26, 2012
I seem to get worse range on the DIR-655 than I did on the DIR-615. I was able to walk out to the parking lot with 1 bar of signal on my phone with the DIR-615. I can get about half way there before I have no signal now that I've got the DIR-655. Are there some settings to disable that might be playing a role in this? I've got the router configured for wireless N only, could that have something to do with it?
View 3 Replies
View Related
Apr 1, 2012
providing an extension for the below antennas cable length for project related requirements with the AP 1262.
AIR-ANT2506 2.4 GHz, 5.2 dBi Mast Mount Omni Ant w/RP-TNC Connector
AIR-ANT5160V-R 5GHz 6dBi Omni Antenna w/RP-TNC connector
View 4 Replies
View Related
Dec 2, 2012
I 'm administration an Aironet 1242ag, and we are currently buying an AIR-ANT1728 as antenna. The standard cable for the antenna is 0.9m long, and It could be insufficient for my needs.
So a few questions:
Can i extend it ?
AIR-CAB050LL-R could fit?
The connectors should be 1 male, 1 female?
View 1 Replies
View Related
Feb 25, 2013
We have been using a SRP521W as the main Router for an office with about 25 users.
So on the cable network it's about 25 computers, 25 IP Phones, 3 printers. Wireless network hold some smartphones and tablets. Computer traffic is 100% Remote Desktop.
That said, for the last few days network connectivity sucks. I think the problem is, precisely, the SRP521W. Some mornings the WAN link is down and can only be brought up by a router reboot.
There's an IPSec tunnel to HQ.
Wireless network was moved recently to a WAP121 to offload the SRP521W. It has two networks: internal and customers with two VLANs.
CPU Usage is around 30-45% all day and spikes to 100% sometimes. RAM Usage is 40-45%. I do not know if this is "too much", "average" or "really low load".
Anyway, time for questions:
a) How can I get a table of active connections on the firewall/NAT to see if there anything "strange" on the network traffic that maybe causing issues?
b) Is there any know bug in the VLAN handling of the SRP that maybe causing the issue? (it's one of the latests changes introduced).
c) If the problem is that there's too much load for such a small router, what replacement would you recommend given the details above? (remember I do not really need wireless on the router as I have the wap121).
View 3 Replies
View Related
May 18, 2011
My internet connect works fine for hours at a time, then suddenly will get 7 or 8 General Failures while pinging (long enough to boot me off the net) then will be back to working fine immediately afterwards.Pinging 127.0.0.1 works fine. I've checked the firewall (Norton) and it has the default settings
View 3 Replies
View Related
Oct 22, 2011
What's the difference between Long and Short Preamble and when to use each of them?
View 3 Replies
View Related
Jun 8, 2011
I'm having a problem with my router a Dlink DIR-655. I know its the router because if I direct connect from my cable modem the problem does not exist. What happens is I start downloading/streaming something it will start and then just stop prematurely causing me to restart it to get it too finish. For example on youtube, I start loading a video it loads normally for 2 mins of video and then will stop. I can get it to restart if I swap video quality and then it just does same thing. Loads around 2 mins of video then stops loading.
I have tried switching browsers, and I changed my MTU size from 1500 to 1300.My motherboard is a GA-P67A-UD4-B3 if that matters. I have the latest firmware on my router.
View 8 Replies
View Related
Sep 25, 2012
I need to implement VSS on 6500 equipped with Sup720-10GE and WS-X6704; considering that this last 10G card doesn't support VSL, I need to realize VSS interchassis connections on Supervisor 10G interfaces, but I only have X2-10G-LR. Considering that the 2 6500 are in short distance (few meters): is it possible to use 10G long range optics and, if yes, do I need some additional patch?
View 1 Replies
View Related
Feb 11, 2013
I am using the 26 character WEP code. Was wondering if it's possible to setup a short password or PIN number. Been troubleshooting problems with a wireless blue ray player that has required multiple resets. Entering the wep code with the remote is hard!
View 5 Replies
View Related
Mar 13, 2012
Recently i have setup a WLAN with inside and anchor 5508 controllers. Standard setup. However, one issue I have is I wish to extend the length of time between password changes for users connected in on the guest wlan. At the moment, 30 is max. I dont have an option on the controller to creat accounts for any longer than that. How to I extend it to 90 days or 120 days?
View 1 Replies
View Related
Sep 14, 2012
So, I just upgraded my mobo/cpu (Z77A-G45 and i5-2500k) and I'm having an issue with my connection as it seems to drop every 5 to 15 minutes constantly and have no idea what exactly is wrongThe kicker is my old mobo did the same thing and I had to do something in win7 to fix it (not sure if it was the drivers or what) but I just can't remember what exactly.
View 1 Replies
View Related
Jul 10, 2011
Just got a WAG120N modem/router , everything is set up and works fine.But I am very disappointed with its wifi range.After using an iPhone and a PSP , I found that, its range is 1,80 meters only, in empty room.Is it faulty ? I cant believe its range is too short although I know that its not "enhanced speed & range" as typed on box.I tried all combination of channels/protocols with no success and it's already flashed on latest version. I really cant connect to my wifi devices.
View 2 Replies
View Related
Apr 19, 2011
how far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both ends of the bridge pair.
View 2 Replies
View Related
Jun 11, 2012
One of my customer has raised a new requirement for implementation of short sequence number format support in PPP multilink header for Cisco MWR 2941 E1/T1 serial interface, whereas router is supporting long sequence number format.here is the output of "debug ppp negotiation" command:-Currently in the MWR debugging logs we can see that by default MWR is sending long sequence header format as below
*Mar 13 01:32:55.438: Se0/2:0 LCP: O CONFREQ [REQsent] id 238 len 25
*Mar 13 01:32:55.438: Se0/2:0 LCP: MagicNumber 0x26CDF693 (0x050626CDF693)
*Mar 13 01:32:55.438: Se0/2:0 LCP: MRRU 1500 (0x110405DC)
*Mar 13 01:32:55.438: Se0/2:0 LCP: EndpointDisc 2 16.16.16.11 (0x1307021010100B)
*Mar 13 01:32:55.438: Se0/2:0 LCP: MultilinkHdrFmt seq long classes 2 (0x1B040202)
While as per the requirement PPP multilink header should support short sequence.
MWR configuration:
controller E1 0/2
framing NO-CRC4
clock source line
channel-group 0 timeslots 1-31
[code]....
View 0 Replies
View Related
Oct 7, 2011
ISP: RCN Type: Cable Security: None, had Microsoft Security Essentials running but uninstalled that to see if it was causing an error. Basic Windows Firewall is enabled (although have tested without)
The problem I'm having is the internet on my HP Pavilion Elite HPE-580t PC will drop for these short 10-30 second bursts. After the drop it will automatically start working again. This happens with all programs I'm running on the computer. The odd thing is that it's in a way random. Sometimes I won't get these drops for 30 minutes but then I'll get them every couple minutes.
I've been trying to pinpoint the problem but haven't come up with anything. I tried plugging the computer directly into the cable modem and still had a problem (which I assume ruled out the router as a problem). It also would seem to rule out this being strictly a wireless issue. I removed antivirus (Microsoft Security Essentials) and have tweaked with turning off the firewall completely. I've tweaked the power saving settings to make sure the adapters are not turning off. Even went as far as blanking the hard drive and re-installing the factory settings.
It's worth noting that I have no problems with other devices online. I have a laptop (uses XP) that uses both wireless and a direct connection to the router without issues. An iPad and Xbox 360 has had no drops when in use. This issue only happens with the desktop. The only difference in this device is it uses Windows 7.It doesn't appear to be the ISP (unless there is something they would do to cause issues with Windows 7) and the issue happens regardless of the router being used or not. It doesn't appear to be the wireless card since it still had issues plugged in. So I feel like it has to be either some setting on Windows 7 or some other hardware issue (Motherboard?).
View 8 Replies
View Related
Apr 17, 2012
I was calculating packet amount of MPEG I use byte rate to divide by 188 byte but now i want to calculate H.264 encode video what is the packet length of h.264? is it same 188byte?
View 1 Replies
View Related
Aug 17, 2011
making EEM work to show first xx lines of CPU utilization. I found when I put cli command "terminal length 13", the EEM stopped working and timed out after 20 seconds. I have tried IOS 12.4(25d) and 12.2(53) with same results. [code]
View 9 Replies
View Related
Jan 19, 2012
I've heard that a method to optimize traffic is to use variable length packets. They say that the worst case is in minimum length packet (64 bytes). But I can't understand why.
View 2 Replies
View Related
Apr 5, 2011
I used 2 PC with gigabit NIC, use cat6 with short cable i've got speed 1000Mbps, but with longer cable(around 30meters) speed is 100Mbps. I'm looking forward to seeing from you soon.
View 1 Replies
View Related
Jan 22, 2012
I would like to know the meaning of 'set max-parse-length 8192' on ACE.Looking at Cisco documentation I found:"you can set the maximum number of bytes to parse for generic protocols by using the set max-parse-length command in generic parameter-map configuration mode.You can set the maximum number of bytes to parse for generic protocols by using the set max-parse-length command in generic parameter-map configuration mode.' what a set max-parse-lenght is?
View 1 Replies
View Related
Sep 13, 2012
Is that possible to increase the pre-shared key length from 30 characters to 32?
View 3 Replies
View Related
Sep 14, 2011
Maximum length of cat 6 lan cable between two switch
View 2 Replies
View Related
Sep 29, 2012
I am installing a network in my small business and was given a spool of Cat5 cable to run wires... I know the length in feet of cable that I was given, but I was wondering if there is some kind of markers on the cable to tell me how much is left... I will be charged for it by foot after I'm done, and I want to know how much I've used. Do I have to just use a measuring tape? Seems unnecessarily complicated... I've checked the wire but can't see any marker of the length remaining.
View 1 Replies
View Related
Jan 26, 2013
In order to get from the coaxial jack on my wall to my cable modem I have to run about a 50 foot coaxial cable around the perimeter of the room.Will the length of this cable diminish the speed of my internet?
View 1 Replies
View Related
Sep 16, 2012
i need to connect modem to computer with the length of 150m. suggest which way is efficient to connect. which cable is efficient. is any medium needed in between.
View 1 Replies
View Related
Jun 13, 2011
The URL field in the web access log has a length of 70 characters. Is there any way to increase is[INFO] Mon Jun 13 21:30:30 2011 Website1234567890012345678900123456789001234567890012345678900123456789001234567890 accessed from 192.168.xx.xx
View 2 Replies
View Related
