I have a problem with an AP1131-AG access point.When I update the CLI it does not update on the GUI and vice versa. The access point is connected to a 3560 switch and there is no WLAN controller involved.
View 8 RepliesI have configured the "ISP" part of the VDSL as i am a tech for the ISP that has access to this, but i am not able to get my 887V to synch is there something i am doing wrong within the Cisco, i have included a debug and couple more things. [Code] ....
View 3 Replies View RelatedI have a brand new lightweight AP that keeps rebooting every 2-3 minutes.
View 1 Replies View RelatedIPods and IPads to connect to stand alone AP1131? My scenario is as follows:
There is a section of a campus that is covered by 14 stand alone AP1131 were I experience the problem. The security parameters are: 802.1x, wpa enterprise, tkip
The other section is under WLC also AP1131 but in this case in WLANs/Scurity/Leyer 2 I checked boxes:
WPA Policy, WPA Encryption TKIP
WPA2 Policy, WPA2 Encryption AES
Auth Key Mgmt 802.1x
Wonder if the fact that I chose WPA2, AES makes a difference with stand alone mode? Anyways I tried configuring AES in stand alone APs and it didn't make a difference since I could not connect either.
I got a report from a branch office which is getting trouble to authenticate users to the WLAN this is a stand alone AP which has a configuration script that we use for all our branch offices but in this case is not working. It seems to be an issue with RADIUS but if it was the case the whole company would be experiencing problems since it is a central RADIUS server.
Here is a log from the AP By the way I modified the radius server timeout to 90 sec
APIMMEXP01#
Sep 1 17:01:47.240: %DOT11-7-AUTH_FAILED: Station 0021.5c7f.1739 Authentication
failed
Sep 1 17:01:53.503: %DOT11-7-AUTH_FAILED: Station 0026.c64b.c3d6 Authentication
failed
Sep 1 17:01:58.739: %DOT11-7-AUTH_FAILED: Station 001e.65cf.9ca8 Authentication
failed
[code]....
We have a site with 4 access point, where two are are showing up in CNA, version 5.7(6), as "Unsupported device" the two others are working fine.
The unsupported devices are:
AIR-AP1131G-E-K9
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The supported devices are:
AIR-AP1131AG-E-K9
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
getting CNA recognize these access points?
I have a Netgear WNR3500L wireless router. I assume it's v1 because on the back it doesn't have "v" anything. Firmware version V1.2.2.44_35.0.53NA.When I connect using g I get 22+Mbps download speed. When I connect using n I get 10 Mbps. I've tried using both WPA2 only (laptop reports 130 Mbps connection I believe) as well as the combo WPA+WPA2 (laptop reports connection of 117 Mbps).Broadband download results don't change - they stay at the 10 Mbps level. I've fiddled with some of the settings on my laptop's wireless card - but the results are the same.For now I'm just trying to figure out where I should focus my investigation and fiddling efforts - on the laptop or on the router.
View 5 Replies View Relatedi have a Netgear N600 Wireless ADSL2+ router on wireless a/b/g/n dual band and all that but what i want to know is will i get better performance if i use a WirelessN card over G on a 10 - 15mb/s connection gaming wise and will it b a great increase over the G causeif its not a HUGE increase then i wont waste my money on a newer card?
View 3 Replies View RelatedMy Acer Aspire 5610Z laptop will automatically connect to public hotspot wireless network but when I attempt to connect to a wireless network at home, set up using a Netgear modem, I only ever get 'local' internet connection only. My wife's HP laptop has no problem making the home wireless connection.
View 6 Replies View RelatedI am running windows vista and have installed the software and windows sees the adapter and states it is working but when it searches for available networks it can't find any. How can I download the driver and install it?
View 1 Replies View RelatedI have a setup involving 3 clustered AP541 running off a sg300 switch. The wireless network setup VAP has one entry for vlan 1 with station isolation disabled. Is there anything more I need to do to allow one wireless client to ping another wireless client - am I missing something - i assume this is possible.Needless to say wireless clients can ping non wireless clients and vice versa quite happily. Everything is running with factory default settings more or less.
View 4 Replies View Relatedoutput are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
View 10 Replies View RelatedWe have recently been given this unusual task. The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition. Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?
i am placing a formal request to Cisco and to the firmware development team to create a new-and-improved firmware release for the WET200 wireless Ethernet bridge, a product that is still being produced, shipped, and sold. I purchased the product about one-and-a-half years ago and have enjoyed its performance. There have been, however, some flaws with the device, namely the following:While configured to use WPA2-based security, DHCP-related traffic is not passed from a router/gateway's DHCP Server to connected devices on the WET200. Current firmware release notes indicate this was a known issue and was, supposedly, fixed; however, due to the level of problems customers are reporting, it appears this may have only been resolved, if at all, with security configurations of WPA, WEP, or OPEN. It has not been fixed for customers using WPA2-based security.When I originally purchased the WET200 and configured it to use WPA2-based security, while it, initially, did have a few problems connecting to my router/gateway, it, eventually, did connect and stayed connected for, approximately, one year. However, in September of 2009, it suddenly lost connectivity with my router/gateway and has not been able to establish a connection since, even after reinstalling the latest firmware revision and after several soft and hard resets of the device. I tested the WET200 with another router/gateway, only to experience the same issue. Other devices are connecting to my router/gateway, but, not the WET200. The last firmware update for the WET200 was dated back in July of 2008. Currently, it is January 2010 and since these issues have been known for quite some time, it is unacceptable that the firmware for this device has not been updated in such a long time, especially when there are known issues with the WET200's firmware. Such lack of support is forcing me and my clients to stop using these Cisco-based products and purchase competing hardware, something I would prefer not to do; however, without better support, I and my clients do not have a choice. Expecting me and my clients to use an inferior form of security on the WET200, such as WEP and/or WPA, until a firmware update is issued is unacceptable, especially when that update has not been released in over one-and-a-half years. Such lack of support is especially unforgettable when my clients and I are looking to purchase new networking equipment. In the past, I would not have hesitated to purchase a Cisco-based product; now, with this experience in mind, I am finding it very difficult to recommend to a client that he or she should invest their organization's finances into Cisco-branded equipment. Proper, professional, timely, support of your hardware is expected of your customers, especially if you wish them to remain loyal customers. I have noticed that other similar devices, albeit, higher-end devices, have had their firmware updated, more recently, compared to the WET200. I assumed this meant that the firmware development team was updating all firmware on such devices. So far, I have been disappointed in the lack of firmware updates for the WET200. While I understand the possible desire to update the higher-end products, first, as a professional whose job is to research, recommend, purchase, install,configure, secure, and maintain both the enterprise-level and small business-level devices, I highly encourage Cisco not to overlook their small business products when the firmware development team is updating firmware for any Cisco products. Deficiency in the support of one strata of Cisco-based products is reflective upon the support of any Cisco-based product and is not easily forgiven by Cisco customers, such as myself, when new and additional hardware needs to be purchased.
View 15 Replies View RelatedDue to lack of wires we decided to extend our network by using WET546 bridge by linksys. Ideally we looking to create topology like this:
(Computer)--eth--(WET546)---wireless----(AP/WLC2100)---(router)---(Internet)
WET546 successfully authenticates and looks pretty healthy on controller (see below) , however neither of computers plugged to WET546 was unable to obtain ip address from dhcp server , nor working with static ip. I was under impression what it might be related to some default policies on WLC2100. Logs (warning) on WLC2100 looks clean.
This is the first time I am trying my hands on wireless gears. I have 2500 WLC and 1142 AP (which I converted from Standalone to LAP).I have a layer 3 POE switch where i am using port 1 for the WLC which is a trunk port.
Port 2 is for the AP using access vlan 111
Port 3 is trunk port going to a router where i am running dhcp server for the VLANs which are as follow:
VLAN 110 -Corp Wireless (10.1.110.0/24)
VLAN 111 - AP-Mgmt (10.1.111.0/24)
VLAN 999 - Guest (10.1.101.0/24)
I wanted to block the traffic from the Guest VLAN 999 but when i apply the ACL on the Guest Interface created on the WLC, I dont see any pings going across and neither I see any hit counts on the deny statement as if the ACL is never applied.
Can the access point AP541N connect to wireless clients with 802.11g/a simultaneously?
View 1 Replies View RelatedI just read that starting from version 7.4, the 2500 controller can be used to terminate guest anchor tunnels. have a question regarding the performance of the internal DHCP server when used in guest environments.
View 1 Replies View RelatedWe have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
Android users can connect to our hospital guest wireless but will not have connectivity. Our wireless infrastructure is WISM based with 2 controllers on 6509 platform. We have a mixed environment of 1231, 1252 & 3502 series APs.
Had issue connecting just Android devices? All other devices connect fine.
I have problem setting up wireless repeater using Cisco 1242AG access points. Here is the setup and problem - The location has 2 1242AG APs and a WLC (2206) which will be used by PDAs. One of the AP was converted to Lightweight AP and is wired. This AP is up and working and PDAs are able to connect to it. There is 1 WLAN and it uses Local EAP (LEAP) as authentication. Layer-2 security is configured as WPA/WPA-2 with 802.1X authentication. Under AAA servers Local-EAP is enabled and a profile (with LEAP enabled) is used. Local users are configured for login. As said PDAs are able to connect and it is working without any problem.
WLC (LEAP with local users) -----> LAP ----> Repeater AP
But the 2nd AP has to be configured as repeater was configured to repeater mode (refering to the document) and was placed. The WLC can see a client (with APs MAC address) but it is probing. The AP is still Automonous AP. Also username and password is configured for authentication. But still the radio on the AP is not up and it is in reset state.
Is 802.11ac wireless module for Cisco Access Point 3602 is available to order ? what Wireless controller we need to use for the support of 802.11ac wireless standard ?802.11ac will support only on 5700 series wireless controller ? Or it will support with 5508 Series also ?
View 7 Replies View RelatedWe plan on buying a Cisco 2700 wireless location appliance but I need to know if it will be compatible with our 2500 WLC.I've tried to look but cant find any document for this. Also can you deploy the location appliance without a WCS?
View 7 Replies View RelatedDoes the Cisco WAP4410N Wireless-N Access Point device have simultaneous wireless N dual-band 2.4 GHz and 5 Ghz capability?
View 2 Replies View RelatedI have a WLC 2006 running 4.2.130 code with AP1020s.I also have several users that have VMware machines that run various flavors of Linux, etc Virtual Machines on Windows XP Pro.
The Windows XP works fine on the wireless. It is the VMWare Virtual Machine running the Bridged ethernet connection that have problems.
The problem is that the Virtual Machine doesn't get a DHCP IP address from the wireless network.
If the user plugs into the wired network all works fine.I have done some captures that show the DHCP requests going out with the MAC address of the wireless client, but no DHCP replies.
It looks like the WLC is seeing the additional DHCP requests from the MAC address of the wireless adapter and dropping them.The same DHCP server (different scopes) are used for both wireless and wired clients.
The DHCP server shows NO activity when the Virtual Machine tries to get a DHCP IP address.The DHCP server is a Cat 6500 running IOS v12.2(33)SXH. DHCP activity was monitored using debug IP dhcp server events/debug IP dhcp server packets. The VMWare Workstation tried is 6.02-6.04.
I have one WET200 Wireless Brigde, connected to internet router... I can't use the infraestructure mode to broadcast the ssid to wireless cliente like laptops,
Only can use the ad hoc mode, but the wireless clients dont reach the internet from adhoc connection trought WET200...The datasheet saids "client only" for WET200, what is the diference between client only and Access Point mode? ??
We have 2 access switches (3750s) that are both attached to a pair of Nexus 5548UPs with L3 cards over VPCs. Access switch (AC1) terminates our 4402 WLC. The WLC services 4 WLANs and connects to the access switch with a single trunked port. Access switch 2 (AC2) terminates an 1131AG lightweight AP. The WLAN is 10.1.1.0/24 on VLAN 300. Router 1 (R1) VLAN 300 IP is 10.1.1.2. Router 2 (R2) VLAN 300 IP is 10.1.1.3. R1 is the active router for VLAN 300. The standby IP for VLAN 300 is 10.1.1.1. The VPCs between both access switches and the router pair are functioning correctly and trunks are wide open (no pruning).
Wireless clients get a DHCP address from a server on another VLAN. Those addresses get handed out just fine.
Wireless clients can ping 10.1.1.3 (R2). They cannot ping 10.1.1.1 (standby address) or 10.1.1.2 (R1).
I took captures from the WLC and I see the ARP requests and replies from wireless clients to their gateway (10.1.1.1). I took another capture directly from the wireless clients themselves. From there, we see the ARP requests, but never the replies. If I create a static ARP entry on the client, it can ping the gateway just fine.
I have 2 cisco Aironet 1252 setup as a point to point link using an external antenna (one radio is setup as the root bridge the other is setup as the non-root bridge). Now I see that the connection between the radios is established at a speed of 54 Mbps. However when I perform a speedtest on the link I see that the my actual download speed does not exceed the 2,5 Mbps. what can cause my actual speed to be far lower than the 54 Mbps? And what can I do to improve it?
View 16 Replies View RelatedI'm setting up a wireless network for a small office with 25 people with approx. 15 on wireless at any time. The office is very long and skinny so I'm looking at a cluster of WAP321's. I'm hoping these will save a ton of money versus buying a controller and more expensive access points.
How do these work for roaming? I tried a search but I've found descriptions of them not roaming at all and descriptions of them roaming but you have to do some kind of pre-authorization right up to they roam with no user interaction, they just roam.
I need the users to be able to roam around the office with no interruption. I don't want to install these and have to rip them out later and put in new ones and a controller. How to find out if the WAP321's will work for roaming.
I recently purchase my first Cisco products for a network for our church. I have a RV180W router, WAP 121 Access Point and a SR2016T switch for our network, which is just pier-to-pier at this point. We have 5 computers connected with ether net through the switch and all see the Internet and work fine. The wireless connection through the router is working fine with our wireless devices (laptops and i Pads). Where I am having issues is with the AP. It is in different area away from the router being powered through POE instead of the regular power connection.
My problem is this: it takes FOREVER to connect to the AP and to the Internet, even when sitting directly under the AP with full signal. Once connected, it appears to allow Internet connection just fine, but getting to that point takes 15-20 minutes sometimes. Also, when I come back the next day, I have NO signal at all, as it seems the AP has "timed out" due to inactivity or something. I have to reboot the AP and the router to get it all back up and running again. I need for the signal to stay up all the time or at least come on when someone connects.
So, what am I doing wrong here? I have recognized and authorized the AP through the router config, security is set up fine and I can see it once it comes up. I have the AP set up as a completely different SSID, although I would prefer to have the AP as merely an extension of the router's wireless network if possible.
Does Cisco WAP4410N Wireless-N Access Point support PPPoE ?If yes how can I configure the PPPoE conexion?
View 1 Replies View Related