I have an Access Point Cisco AP541N, working great, except that every 1 or 2 weeks, clients cannot connect anymore to it. I need to reboot it.
I recently updated the firmware to the latest version (AP541N-K9-2.0(0)), but that didn't work.
Is there a way on cisco access points to automate a daily reboot?
We have two Cisco Wireless Controller 4404 with the IOS Version 7.0.220.0 and a lot of access points (ca. 170). Now i wan't to reboot a group of Access points where i found over a filter..Or how can i reboot all the Access Points at the same time over the Controller Interface? Is it possible? I only found the option in the WebGui where i can reboot 1 Access Point at the same time with "hardware reset".
View 5 Replies View RelatedRegion : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
ISP : Comcast
TP-LINK WDR4300 750N Dual-Band router issue.
I started having a problem with a VONAGE V-Portal VoIP adapter losing connection to the Vonage server. I Unplugging the adapter and waiting doesn't solve the problem. The only way I can temporarily fix the issue is to reboot my TP-Link router. Once the router is rebooted the adapter can connect to Vonage. After a few hours it loses connection again. I have set the adapter to use a static IP outside of the DHCP reserved pool. This didn't fix the issue.
I have had vonage for many years and this router for the last 10 months and not had a problem until the past two weeks. Nothing only my local network changed. All of my PC's have no problems with internet access during the time that the Vonage adapter gets an Error 004 (lost connectivity). I still have connectivity with my ipod touch and other internet enabled devices as well. I was using 8.8.8.8 as my DNS server in the router DHCP configuration as well as the static value when I tried using a static IP with the V-Portal. I then switched all system to the ISP (Comcast) preferred DNS servers. The problem still exists. The only way to get the Vonage adapter back to running is to reboot the router.
I should mention I have Motorola Cable modem to a TP-LINK WDR4300 750N Dual-Band router. I have two Vonage vportal adapters plugged into the a couple of the LAN ports on the TP-LINK router. One vportal is my roommates, one is mine. Everything has been working fine for the last 6 months and now one or the other Vportal loses communication through the router, but the other vportal doesn't lose connectivity. It only happens to one of them and it varies as to which one will ERROR out.
Have a Cisco 2500 WLAN with Cisco 1142 Lightweight Access Points.IOS: WLC & AP IOS is 7.4.100.0
Seems to be when the APS reboot or lose power we cannot issue command to bring the APs back up from the WLAN- we have to log onto each AP via a console cable and bring the interfaces up.
Is there a way to have the router reboot every day automatically? Every few days no one on the network is able to use the internet until the router gets rebooted (which has to be done by unplugging it at that point, since I'm by then unable to connect via the web interface), and having it automatically reboot every day at a time when everyone is usually sleeping would be very convenient.
View 9 Replies View RelatedI recentlydeployed a RV220W and got it mostly working for the environment. One issue: remote users connecting from different locations. I set up QuickVPN to accomodate them, which seems to 'kinda' work. 'Kinda' because I have to reboot the RV220W each day before the clients can connect succesfully. The clients run a mix of WinXP-32, WinVista-32 and Win7-64. All other settings in the QuickVPN client have been verified for each user. They each have the latest verion of QuickVPN and the RV220W firmware is at the latest version. The networks at the remote locations are not numbered the same as the host location.
The clients work several times a day, but the RV220W needs to be rebooted every morning. Is this a known problem with a work around? Is there a better solution for VPN access from Vista-32 and Win 7-64?
Everytime I boot up my Winows 7 desktop the new E900 requires a security key to login.
Can't seem to get the settings right to automatically login like my laptop does. Routers can be humbling.
I have 2 AP541N access points. Have been working well for a couple of years. Later last year they just dissapeard from CCA one day. COundt access them but they were still delivering 'wireless' so to speak I have recently put them back to defaults to try and get them back in to CCA. i had one, but not the other. They would work fine via GUI/web access.Then i updated them to 2.0.4 (both images) and since doing that i have no access to either of them via any form.
View 2 Replies View RelatedI have a Cisco AP541N and have been attempting to configure it. I assigned a Static IP with the Subnet, default gateway and DNS info. Everything seemed to be working fine yesterday when it was deployed. Today, there appears to be no internet access. We are able to connect but have limited access.
View 3 Replies View RelatedI currently have two AP541N access points. Both are configured for internal access and one unit is configured with a Guest VAP. I want to configure the Guest VAP to redirect to an authentication page so that the user connecting has to log in to get internet access. I'm fairly certain the AP541N doesn't offer this out of the box. I know I can redirect, but what is needed to force a user to authenticate to gain internet access. I want to find out what additional hardware/software I will need in order to create Guest Services of this VAP.
View 1 Replies View RelatedI have installed the following wireless access point on our network:
-Product Identifier: AP541N-E-K9
-Hardware Version: V01
-Software Version: AP541N-K9-2.0(0)
I have created 2 VAP's and give each one an SSID. They both have the same VLAN ID. I have setup as follows:
1) The first VAP I would like to give internet access and access to our internal network shares.
2) The second VAP I only wish to give internet access and no access at all to our internal network (for guest access). I am also using HTTP redirect with this.
how can I achieve the setup in number (2)? This is to give internet access, but not share the internal network.
AP has static IP with 2 SSIDs setup, one for guest one for domain access(both have the same issue), tried with multiple devices, both win and MAC, all show "connected but with limited access", ipconfig on those devices, all show ip "169.254.X.X", but event log on AP indicates that "authentication has been completed sucessfully".
using RADIUS server for authentication. management VLAN ID "1", SSID VLAN ID "11"
Can I add an AP541N into a existing wireless network of WAP4410N's without any issues.
View 4 Replies View Relatedap541n in cluster access point exists a master ?
View 3 Replies View RelatedCan the access point AP541N connect to wireless clients with 802.11g/a simultaneously?
View 1 Replies View RelatedI have a client that has 3 AP541N's and they want to enable guest wireless access. However, their VOIP provider has their managed switches locked down so we can't add VLANs, etc.So I cannot touch the switch or router config on this LAN.
Looking into AP541N documentation I see VAPs mentioned, can I enable those and have secure guest wireless access with the same private IPs that the rest of the LAN use right now? (That is, the employees are 192.168.2.x and the guest wireless users would also be 192.168.2.x.)
Or do I need to do something else to properly enable guest wireless? Like add another piece of equipment? I did try to add a Cisco RVS4000 to the mix but it wouldn't pass the VLAN across the switches that I setup for the guest wireless SSID. goal is to leave the switch and router in place, and work with the AP541N's that I have and get secure guest wireless.
We have a Cisco ASA5505 here that provides DHCP and routing to all our devices in our network. We also have a few other switches and wireless access points connected directly to the back of the ASA5505.For the past year all the wireless network signals has been working fine however starting last month, none of the wireless access points (we have three WRT54G) would allow proper connection (dropping connection, slow internet).I thought this maybe all THREE wireless access points are toast/bricked. So i went out and bought brand new Netgear WN604 and even with the new WAP i'm having same connectivity issues (really slow internet).When hardwired directly to the switches we get BLAZING fast internet & connectivity, no issues.
I called CISCO TAC and they automatically said "our ASA5505 is fine, it has to be your wireless access points" not working properly. I explained to them that i also purchased two brand new access points and they are doing the samething now, how can that be?
I've had some long standing issues that I've tried various things to fix. I have two WAP4410N access points set up at a smaller sister company. Wireless clients (laptops) are not receiving DHCP assigned IP addresses. If I type in an IP manually, it works fine.The sister company has a point to point T-1 connection to our main building. Our main building has the DHCP server. The router on the sister company end is configured as the DHCP relay.
I've upgraded the firmware three different times in the past to hopefully resolve the issue, but no luck. Just today, on one of the WAP4410N's, I upgraded to the 2.0.6.1 firmware (backing up config, reset to factory default, upgraded firmware, reset factory default again, restored config). After the first reset to factory defaults, the Access Point itself picked up a DHCP address from the server, and I verified this in the DHCP console on the server, so I know that the DHCP relay is working. However, my laptop would not get a DHCP address when connecting wirelessly through that access point. It is a Windows 7 Enterprise laptop. I also could not get a DHCP IP with my iPhone connecting to wireless, to rule out specific issues with just a laptop.I have the DHCP lease times for the subnet that these WAP4410Ns are on set to 2 hours.
To put a cherry on top, there is one laptop that stays in a lab area at all times, connecting wirelessly, and it DOES get a DHCP IP address (I can see in the DHCP console that the lease for this laptop continually renews as needed). I do remember on initial config when I couldn't get it to work, that I did a manual set up, gained connection, then switched it to DHCP...but that doesn't work for any other laptop.Why would the access points get DHCP address, but not anything connecting to the Access Points?
Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs. But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.
Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?
At my school we have a lot of access points, but sometimes the computer use the wrong access point. How can I solve that? Is there a program for switching access point?
View 8 Replies View RelatedBTW the halls are next to each other.The house and the 3 halls are in the vicinity however not attached together(i.e. wall to wall). The distance between the house and the first hall is approx 1 road width distance.ISP is Virgin and the internet was installed this year hence has the latest Virgin Home Hub.I am aware that i probably require 3 wireless access points (1 for each hall).The first wireless access point will need to be connected with a RJ-45 cable running from Home Hub. Can i connect the Wireless access points up together or do they all need to come from the ADSL hub?I am not sure what Wireless access points would be best and how to go about connecting this all up
View 2 Replies View RelatedI have New Pace 4111n Wireless Router that I got from AT&T and is setup on 1st floor, but its wireless range does not get me to 2nd floor. I also have the 2Wire wireless router from AT&T. In Addition, I have ethernet connection from level 1 to level 2 as well.
I was wondering if it is possible to have the Pace Wireless N router to work as modem and wireless access point, at the time use the 2Wire router to broadcast wireless and act as access point for 2nd floor.
IF its doable, how should the two be configured and connected.
I am 17 routers Cisco 837 With Cisco IOS Software, C837 Software (C837-K9O3SY6-M), Version 12.3(2)XE4, RELEASE SOFTWARE (fc1)
My tunnel is mounted but falls after 1 day.is there a way to automate the recovery of the tunnel without rebooting the router !
[code]...
I am trying to deploy several AIR-CAP3502E-E-K9 access points from a cisco 5508 wire lan contoller running ver 7 code. However iam having difficulty registering the access points with the WLC. The wlc is connect to a 3650 switch, and each access point is connected to a 2960 switch. A bad update was not allowing the access points to get their correct firmware.
View 7 Replies View RelatedI am having an issue here. I have 2x 5508 that each have 100 AP license and a little under 200 access points. Basically all of the access points are using DNS to connect to the primary controller that has the DNS entry. Basically half of my access points need to be on the second controller and in order to do this I have been using the high availability mode of each access point to push them to the second controller IP address.It was working perfectly until now. I have pushed 28 access points to the second controller and the last two I need to push at this location just keep resetting on the primary controller. Neither controller is configured as master controller.
View 4 Replies View RelatedI need an Wireless Access Point.Two SSID simultaneously in different IP Rangeit is with a simple browser GUI to manage? (not console and controller)a distance of about 50 (we can place multiple APs)N speedDual BandWhich series meets the above requirements?It can also Wireless-N Gigabit Router as 4400N, but it does not support Dual Band.
View 1 Replies View RelatedI have access points deployed across several buildings that each have a different IP scheme and their own T1 line. Is it possible to configure the 5508 controller to allow these access points to use the IP scheme assigned for that particular building or will dhcp always assign an IP address to the connecting client based on the IP scheme of the building that the controller resides in?
View 1 Replies View RelatedI need an official document from Cisco saying the APs models supported by the WLC 5508. Specially, I need to know if the AIR-AP1242AG-T-K9, converted from standalone, will be supported by the 5508.
View 1 Replies View RelatedWe have a couple of Access Points which are not registering with WLC 2500. I followed-up on the two LAPs in the dorm. They were cycling through red, amber, green, indicating they were trying to join the controller but could not.
Recently, we have changed our IP Schema for the Wireless Devices and I believe there is an IP Conflict between APs and WLC. Earlier APs were cofigured with Static IP Address assignment, thus they can't change their IP Address.
how to reset the Access Point? I know we can hard reset them by pressing the Mode button manually.
Is there another way via which this can be done witout removing the Access Points from their enclosures?
I have multiple cisco 1130ag access point at one of my clients villa. The issue I am facing is when moving throughout the buildingthe laptop and smartphones will not switch between AP’s unless it loses its connection with its existing AP then it will see the other AP that is closer and connect to it.
For example, I start at one end of the building where it connects to AP#1 , if I then slowly go to another section of the villa, it it will not switch over to AP#2 until the signal is lost from AP1
I have following settings
AP's are Cisco 1130AG
Single SSID with WEP Security
install AP1042N access points?
Situation: I have a store where there is already installed an AP1042N. In the back of the building there is no wireless signal. I want to install a second access point to extend my range;
At home, I use my laptop to connect to my wireless router without any trouble.But at: public libraries, Starbucks, hotel rooms... any free public wifi? All attempts to connect meets with the same error: "unable to connect to network" (preceded by the system hanging for a lengthy amount of time). Windows advises me to unplug the router and plug it back in, which obviously isn't an option.It's annoying to troubleshoot, because I'm only having the problem at times where I have no wired access (hence: no way to get to forums like these and look for an answer, update drivers, whatever).
View 6 Replies View RelatedI have a customer who wants wireless for his entire school campus. In the gymnasium, he says that there will be at lease 500 people with wireless devices at one time during a game or event. How many access points will I need to provision to accomplish this request? We are quoting the AIR-CAP3602I.
View 2 Replies View Related