I have to upgrade a WCS from version 6 to 7, here we have a MSE having a 6.0.85.0, the matrix document indicates that you can map or well,having installed only one version or release from MSE to WCS, my question is, do i have to upgrade first the mse to the compatible version to the new wcs version we want to upgrade?
View 1 RepliesI used ASDM to upgrade a 5505 tonight and now I get the error message attached. How/where do I find out which versions are compatible?
View 2 Replies View RelatedI got a few Cisco Aironet 3602i. The minimum WLC version to support these is 7.1.91.0. I am planning to upgrade to 7.2.103.0. The minimum WCS version to support these WAP is 7.0.220.0 and the next available 7.0.230.0. Checking the release notes for both of these WCS versions, there is no mention of support for WLC versions listed above.
URL
Am I missing something here ? What versions would be required on WCS and WLC to make all the three entities (WLC, WCS, WAP) inter-operable ?
I am configuring two 2504 controllers, which I ordered together, however they run different software versions and I don't have a contract/ login to download wlan controller software from the Cisco website. The one with the newest version runs 7.2.103.0 while the other one runs 7.0.220.0 I want to run them together in the same subnet and use them for redundancy (10 AP's will connect).
Is there a way I can download the software from the controller, just like I am able to do with an ASA firewall? Then I can upload it to the controller with the older software version.
We have Internal Wireless Controllers to be set up for HA (AP SSO) and wireless traffic from Guest SSID will be terminated on a Guest Anchor Controller inside Firewall DMZ. The Internal WLC controllers are installed with software versions 7.3.101.0, and the Guest Anchor controller is installed with software version 7.2.103.0. Just wondering if the Guest Anchor controller needs an upgrade to match the software versions on the HA controllers. Also, Cisco provides a new version of code, 7.3.112.0 now. So is it recommended to install the new software version on the HA controllers as well as the Guest Anchor Controller.
View 8 Replies View RelatedI have 2 laptops, one is running VISTA and one is running Windows 8. They are connected to my wireless router. I also have a desktop running Windows 7 that is wired to router. I have searched the internet and cannot find how to set up a new network without using a HOMEGROUP?
View 2 Replies View Related I have many of these, many models and versions. I have a WRT54G v1, V1.1, V2....V8, I also have WRT54GS's WRT54GL's and others, Lots of other Linksys stuff, almost all of it in the Blue and Black boxes of varing sizes.I have a heck of a time when I reconfigure my network or the wife changes the furniture. I'd love a single document that lists the power specifications and adapter requirements for thens devices... I can't find them any where on the Linksys site. I Have looked and searched and nowhere can I find a consolidate list.
Any have a list of the DC power Specifications, Barrel sizes, and other stuff needed to buy a replacement Power adapter. This page url...lists a lot of information but does not list this critical information... I am amazed that Linksys does not have it listed some where here. Losing a wall wart should not be a reason to pull you hair out, just a simple purchase, If they don't want to stock them, then at least tell us what they are.
I have a problem with current (1.0.06) firmware on WRT120N. Few hours after restart DHCP server stops assigning IP addresses. Another restart resolves problem, but only for next few hours.Computers and other devices "see" my wireless network and they are able to connect to it, but the process stops at requesting IP number.There was no such effect with original firmware (although there was another problem with 2200BG), so I want to downgrade.where can I find previous versions of WRT120N firmware?
View 2 Replies View RelatedWhich IOS versions or images on WS-C4503 Sup V switch and 12404/PRP routers support any EEM version 2.0 and above?
View 1 Replies View RelatedI have 3 WLC's currently running version 7.0.116 and a WCS on version 7.0.220. I am looking at upgrading the versions and am uncertain as to the compatibility.
1. Upgrade the WCS to 7.0.240, and upgrade the WLC's to 7.3. Resulting in my WCS just not able to manage the "new features" in the latest WLC code?
2. Upgrade the WLC's to 7.3 resulting in WCS completely unable to manage the WLC's? I am aware there is WLC 7.4 code however I've read there is an issue with 1142 AP's rebooting.
We are updating our older Pix boxes to ASA 5525s. A book covering the new versions of 8.x code.
View 3 Replies View RelatedI am in the process of rebuilding our ASA 5540 pair. We are currently on 8.2 code with this set of firewalls and I was going to upgrade it to 8.4 being I have a couple of other firewalls running this code currently and am familiar with it. That said, I saw that the 9.x code is out there now. Are there any major advantages or caveats with the 9.0 code? I plan to use this firewall with SSL VPN and RSA Secure ID integration for the next 2-3 years at least. Any quick pointers on these two code versions and on upgrading to 9 or staying with 8.4 line.
View 2 Replies View RelatedWhy do some versions have heatsinks and others don't? The HP branded cards EH352AA always seem to have the heatsink, but very few Intel branded cards have it. I'm talking about the single port NICs - all dual+ port cards have the heatsink.
View 2 Replies View RelatedWe have 3200 logical devices configured on CiscoWorks and CiscoWorks is running very very slow. CiscoWorks installed on server with Windows Server 2003 32-bit and this version of windows it can only support RAM up to 4GB, which is already installed. In order to increase the RAM we have to upgrade the windows version as well. Which versions of Window can perform best with CiscoWorks. E.g. Windows Server 2003 with Service Pack 1 (SP1), Standard Edition 64-bit: or Windows server 2008 etc. We are currently using the LMS 3.2, RME 4.3.0, CM 5.2.1
View 2 Replies View RelatedI am working for a customer on an enterprise site containing many 6509's. We have built a test environment and upgraded a chassis from sup720 running 12.2(18)SXF15 to VS-S2T-10Gb running 12.2(50)SY on the management card. I have noticed and so has the customer that there are many commands missing or added and they want an expalnation of these. I can do some of them easily, change syntax etc but for instance it has added a table-map, 50 vlans with a large MTU and large COPP policy.
What are these ?? and also is there a quick way resource etc to find out why the commands have been added/removed, for instance-mls ip cef load-sharing full is missing--
My company AP 1231G is not passing the DHCP address to the client from the DHCP server, my config listed below basicly the AP is on its own VLAN 10.1.123.1 and the DHCP server is 10.1.10.2 -- trying to use iphelper to pass DHCP to clients and the AP is on static IP 10.1.123.2--
!
! Last configuration change at 13:15:56 +0800 Fri May 25 2012 by root
! NVRAM config last updated at 13:15:56 +0800 Fri May 25 2012 by root
!
[Code].....
Just setup two WAP200E's, the bridge is "Connected" as I look Status > System Performance in both WAP's. However, I cannot get to the LAN from one network to the next. Cannot even ping the WAP's from either side.
I already have two WAP200E's on this network, that have been working well for month (164 day uptime), and they are configured with a wireless bridge between them, both networks on the same LAN (same 192.168.2.x network on either side). The bridge names are different, different from the main WiFi in the building, too (if it makes a difference), and the static IPs the WAPs have don't appear to have any conflicts on the network.
This is actually three buildings, one is the main one with a Cisco SR520 for a router, and a Cisco SF 200-24P switch. So two WAP200E's go into this switch now, and I see them both fine when going into the management interface. Then each of the other buildings has one WAP200E, and a small Netgear 8 port PoE gigabit switch at each building to power the WAP.
The Netgear switches aren't managed, and I've made sure any features like STP, VLANs, etc. are turned off. And the Cisco SF 200 switch is set at auto and all the defaults mostly, particularly for the ports. I tried doing a SmartPort for this latest WAP200E and that didn't change anything, tried disabling STP for it too, and no change. The PoE port for the working WAP200E is identical in config to the PoE port for the new WAP200E, and both show forwarding, all VLANs admitted (none are enabled, no VLAN tagging, etc.).
So now I am wondering if I can have two WAP200E's into one switch? Or two bridges on the same LAN subnet? Or is there something else I am missing or should configure?
I have 2 1242AG APs setup with one SSID and no vlans configured. The APs are connected to a switch along with my DHCP server. Clients are able to connect to the SSID but are unable to get an IP from the server. Clients can plug into the switch and get an IP. If I configure a static IP on the wireless card, the client works fine.
Is there something I'm missing on the AP to allow DHCP requests to pass through? IPhelper?
Here is the AP info: AIR-AP1242AG-A-K9 12.4(21a)JA1
Our brand new WAP321 is configured manually because the setup wizard would not complete, just hangs at the end.
Anyway, when a client connects to the AP, it cannot get an IP address. It is able to connect to the AP but does not pickup an IP from our internal DHCP server. I've been up and down tthe config screens and even tried hard resetting the AP and starting from scratch to no avail. This happens with 2.4Ghz and 5 Ghz modes.
I've tried laptops and smartphones with the same result.
I have LMS 4.1 and I'm trying to render a Nexus 7010 in Ciscoview. I have downloaded the latest package files. The Sup2 and Fab2 modules (N7K-SUP2 and N7K-C7010-FAB-2) show as "unsupported card".What packages and versions are required to recognize this card with LMS 4.1?
View 1 Replies View RelatedI'm putting together a lab to start on my CCNA and I've got two 3640s and two 2620s. I want to upgrade all of the units before I start on the CCNA and I'm having trouble working out what the final rommon version is for each of the routers.My 3640's are on version "Version 11.1(20)AA2". Is this the final release ?
One of my 2620's is on "Version 12.2(10r)1" and the other is on "Version 12.2(6r)". Is "10r" the final release for the 2620 ?I've also seen a few sites mention that either version "8r" or "3r" of the 2620 rommon adds support for 32MB flash SIMMs. Is that correct ?Is there a document that describes the differences between the different releases ?
We have a WEB VPN running on Cisco ASA 5510 (SW = 8.2.1 / ASDM SW = 6.2.1). There are multiple internal (Web) applications are published on it and are working. One of the Web Application is working from internal network but from outside (or internet) through Web VPN, it is getting stuck and trying to load JAVA version. It is to be mentioned here, the latter web application is required Java Version 1.4.2 while the working applications are working with Java 1.5.1.
Is it possible to mount the more than on Java version on Cisco ASDM to be worked together ?
We have setup a bridge between two of our offices using two WET200's in adhoc mode. Everything is connected fine and the signal strengh is good. All traffic pass's over the bridge correctly but DHCP requsts/replys seem to be failing to traverse the bridge. Our DHCP server is hosted on site A and the computers on site B fail to obtain thiers IP's from the dhcp over the bridge requiring us to use static IP's.Firmware is currently the latest.
View 1 Replies View RelatedI have a Cisco RV220W running the latest firmware (currently 1.0.4.17), and I have noticed that after about a week of use, wireless clients can no longer acquire IP addresses via DHCP.
I have used Network Monitor on both the DHCP server, and the WiFi client, and can see that the server is receiving the requests and sending a reply, but the client never sees the response from the server. So far the only way to resolve this is to reboot the router.
How can I find out the firmware versions for IOS, modules and components of Cisco catalyst 4500 series switch. I can see the firmware version of IOS in show version command but how can I find it out for the modules or components of the switch.
View 4 Replies View RelatedA little background on me: I do performance testing for a large corporation, so networking is like an old hat for me - but this has me spinning because it makes no logical sense to me.Here's the layout of my home network:CableModem(passthrough) -> WRT120N -> ENH200 (Access point) -> ENH200 (Client Bridge) -> Netgear N600Both the WRT120N and the Netgear N600 are providing wireless access to clients at both locations. N600 is set not to route or DHCP, and the WAN port isn't used.Initially the WRT120N wasn't in play because the cable modem was serving DHCP, but it wouldn't successfully send DHCP to most clients on the other side of the client bridge. So I installed the WRT120N (old, I know) and it was able to serve up DHCP to any and all systems... for a while. Now DHCP doesn't appear to be working fully again on the Netgear side of the bridge. One device registers in the WRT120N, the client list shows the mac as getting assigned an ID, but the device never actually pulls the address. Static works fine. Those that already have DHCP addresses work like a charm, so I know the link is stable. pingtest.net reports near perfection.
View 4 Replies View RelatedI have the bridge working but I have to assign a static IP address to devices connected to it. I can't get it to pick up an address from my DHCP server. Here's what I have:
Cisco ASA5505 (Firewall & DHCP server)
WAP54G - Access Point
WET610N - This Wireless Bridge
The ASA5505 successfully gives DHCP address to ALL wired and wireless computers. The WET610N has connectivity to the WAP54G. The status page indicates it's connected and I can get on the internet if I set a static address. However, once I configure my computer to automatically get an IP from DHCP, it just times-out and says limited or no connectivity. Again, when I set a static IP, I have connectivity to everything. I know the AP is working because I can get an address from my DHCP server (ASA5505) with my other laptops and even my cell phone. Why can't I get a DHCP address through this bridge (WET610N)?
Is possible to setup DIR-655 as a Wireless receiver passing the signal to the other devices by ethernet?
View 2 Replies View RelatedI'm thinking about changing my home router (have WAG300N now) and my big concern are GRE and ipv6ip tunnels. Righ now I experience that every few days WAG300N stops passing GRE traffic from inside of my network therefore my ipv6ip tunnel goes down. The only way to sove that is to completly reload WAG300N router.
passing ipv6ip and GRE tunnels through E4200 or EA4500? I see no passthrough in configuration option for those routers.Also performance question - I have 64Mbit symmetric internet connection. I guess both routers would easily handle that with SPI turned on and NAT?
I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies View RelatedI am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
I've looked at many others having this same problem, but can't seem to figure out what my problem is. Same issue as most, I can connect fine, I get an IP, but it won't pass any traffic, I can't ping anything or access anything.
View 8 Replies View RelatedI have a vendor that currently uses a Cisco 871 as a VPN router in our company network, they use it connect to provide services to one of the servers in our LAN for our customers. Recently, we are going to be setting up a 24/7 call center with this vendor, they will be accessing a server in our network through the VPN to provide customer service during after hour periods.We have a problem however, with an application that is hosted by another vendor that is critical for our regular company call center. Access is reached with this application through this vendor by way of IPSec VPN tunnel that is built in our company's Cisco ASA 5510. This application is accessed via Internet Explorer that goes across to access the application at the endpoint
I need to figure a way by which the vendor that will be running the 24/7 call center coming through their tunnel in our network to connect over to the tunnel on the vendor on my ASA. Im likely going to have to set some routing of traffic in my internal default gateway router for this to work.