Cisco WAN :: 3640s / 2620s - ROMmon Versions For Older Routers
Jul 11, 2012
I'm putting together a lab to start on my CCNA and I've got two 3640s and two 2620s. I want to upgrade all of the units before I start on the CCNA and I'm having trouble working out what the final rommon version is for each of the routers.My 3640's are on version "Version 11.1(20)AA2". Is this the final release ?
One of my 2620's is on "Version 12.2(10r)1" and the other is on "Version 12.2(6r)". Is "10r" the final release for the 2620 ?I've also seen a few sites mention that either version "8r" or "3r" of the 2620 rommon adds support for 32MB flash SIMMs. Is that correct ?Is there a document that describes the differences between the different releases ?
View 3 Replies
ADVERTISEMENT
May 21, 2013
I have some legacy (read: old) audio equipment that used leased lines to run, no way to convert them to IP internally. They have x.21 and v.35 interfaces on them.
Is there a way i could use something like an old 2600 series router and run it in reverse, like just using them as a media converter to shove the v.35 over into IP land?
I'm not interested in buying newest latest greatest (these audio codecs are upwards of $5k a pop to replace, x2 for a complete link), i'm just curious if i can turn a WIC-1T into the interface for these boxes and do a direct route to another 2600 on the other end with the same configuration.
This would essentially turn the WIC portion into the local side and the ethernet into the WAN side.
View 2 Replies
View Related
Mar 4, 2012
We have several RV042 routers with older firmware version 1.3.12.19-tm.We have purchased new RV042 routers as hot spare replacement that's coming with firmware version 4.1 installed.
We have a VPN tunnels between multiple sites using the older firmware version.
My question is: Will a RV042 with firmware version 4.1 connect to a RV042 with firmware version 1.3.12.19-tm and vice versa?
View 3 Replies
View Related
Dec 13, 2012
We have a CISCO RV042. We are about to begin a VIOP service with Vocalocity who state:
The RV042 is a wired router that requires no configuration adjustments for the firmware versions we tested. Version 1 and 2 are compatible. Version 3 is NOT. Firmware Reviewed: 1.3.12.6 | 1.3.12.19
Our router's firmware is : 1.3.8.2 (Feb 12 2007 10:43:08)
Can we upgrade to 1.3.12.6 or 1.3.12.19? What is meant by Version 1, 2 and 3?
View 3 Replies
View Related
Feb 17, 2011
I have an old Cabletron switch i have used for about 8-10 years, it has some vlans set up and i was wondering how i can "talk" to the switch and set it up. I am using this switch in my home on my vast network. is it possible to "reset to factory" or anything without a serial cable? I would like to use snmp of telnet to configure but i dont think it has an ip set up and it is such an old switch I cannot find any info from entrasys.
View 1 Replies
View Related
Dec 16, 2012
I am trying to configure an older Belkin Router (Model Number 5FD8230-4) as an Access Point so that I can boost the range of my network. The problem I have is in configuring the old router. It won't allow me to change any settings, or at least the changes don't stick, even after clicking "apply changes". I tried creating an administrative password but I am not even sure that this is working. I am using a Macbook, so perhaps this is an Apple compatibility issue. I have tried resetting the router and reverting to Factory default settings, but no joy.
View 3 Replies
View Related
Dec 10, 2012
I have an iMac running 10.4.11. I would like be able to print through the router. I now have my PC laptops doing so. What voodoo do I have to do to make the iMac work with it?
View 3 Replies
View Related
Mar 22, 2012
why does my 2811 routers boot to rommon after uploadig IOS c2800nm-ipbasek9-mz.151-4.M1.bin
View 1 Replies
View Related
Sep 19, 2011
Which IOS versions or images on WS-C4503 Sup V switch and 12404/PRP routers support any EEM version 2.0 and above?
View 1 Replies
View Related
Mar 5, 2012
I got a few Cisco Aironet 3602i. The minimum WLC version to support these is 7.1.91.0. I am planning to upgrade to 7.2.103.0. The minimum WCS version to support these WAP is 7.0.220.0 and the next available 7.0.230.0. Checking the release notes for both of these WCS versions, there is no mention of support for WLC versions listed above.
URL
Am I missing something here ? What versions would be required on WCS and WLC to make all the three entities (WLC, WCS, WAP) inter-operable ?
View 4 Replies
View Related
Mar 6, 2013
I have 3 WLC's currently running version 7.0.116 and a WCS on version 7.0.220. I am looking at upgrading the versions and am uncertain as to the compatibility.
1. Upgrade the WCS to 7.0.240, and upgrade the WLC's to 7.3. Resulting in my WCS just not able to manage the "new features" in the latest WLC code?
2. Upgrade the WLC's to 7.3 resulting in WCS completely unable to manage the WLC's? I am aware there is WLC 7.4 code however I've read there is an issue with 1142 AP's rebooting.
View 2 Replies
View Related
Dec 4, 2012
We are updating our older Pix boxes to ASA 5525s. A book covering the new versions of 8.x code.
View 3 Replies
View Related
Apr 23, 2012
I have to upgrade a WCS from version 6 to 7, here we have a MSE having a 6.0.85.0, the matrix document indicates that you can map or well,having installed only one version or release from MSE to WCS, my question is, do i have to upgrade first the mse to the compatible version to the new wcs version we want to upgrade?
View 1 Replies
View Related
Feb 28, 2013
I am in the process of rebuilding our ASA 5540 pair. We are currently on 8.2 code with this set of firewalls and I was going to upgrade it to 8.4 being I have a couple of other firewalls running this code currently and am familiar with it. That said, I saw that the 9.x code is out there now. Are there any major advantages or caveats with the 9.0 code? I plan to use this firewall with SSL VPN and RSA Secure ID integration for the next 2-3 years at least. Any quick pointers on these two code versions and on upgrading to 9 or staying with 8.4 line.
View 2 Replies
View Related
Jul 31, 2011
Why do some versions have heatsinks and others don't? The HP branded cards EH352AA always seem to have the heatsink, but very few Intel branded cards have it. I'm talking about the single port NICs - all dual+ port cards have the heatsink.
View 2 Replies
View Related
Aug 6, 2012
I am configuring two 2504 controllers, which I ordered together, however they run different software versions and I don't have a contract/ login to download wlan controller software from the Cisco website. The one with the newest version runs 7.2.103.0 while the other one runs 7.0.220.0 I want to run them together in the same subnet and use them for redundancy (10 AP's will connect).
Is there a way I can download the software from the controller, just like I am able to do with an ASA firewall? Then I can upload it to the controller with the older software version.
View 3 Replies
View Related
Aug 3, 2011
We have 3200 logical devices configured on CiscoWorks and CiscoWorks is running very very slow. CiscoWorks installed on server with Windows Server 2003 32-bit and this version of windows it can only support RAM up to 4GB, which is already installed. In order to increase the RAM we have to upgrade the windows version as well. Which versions of Window can perform best with CiscoWorks. E.g. Windows Server 2003 with Service Pack 1 (SP1), Standard Edition 64-bit: or Windows server 2008 etc. We are currently using the LMS 3.2, RME 4.3.0, CM 5.2.1
View 2 Replies
View Related
Apr 26, 2012
I am working for a customer on an enterprise site containing many 6509's. We have built a test environment and upgraded a chassis from sup720 running 12.2(18)SXF15 to VS-S2T-10Gb running 12.2(50)SY on the management card. I have noticed and so has the customer that there are many commands missing or added and they want an expalnation of these. I can do some of them easily, change syntax etc but for instance it has added a table-map, 50 vlans with a large MTU and large COPP policy.
What are these ?? and also is there a quick way resource etc to find out why the commands have been added/removed, for instance-mls ip cef load-sharing full is missing--
View 1 Replies
View Related
Feb 25, 2013
I have LMS 4.1 and I'm trying to render a Nexus 7010 in Ciscoview. I have downloaded the latest package files. The Sup2 and Fab2 modules (N7K-SUP2 and N7K-C7010-FAB-2) show as "unsupported card".What packages and versions are required to recognize this card with LMS 4.1?
View 1 Replies
View Related
Feb 12, 2013
We have Internal Wireless Controllers to be set up for HA (AP SSO) and wireless traffic from Guest SSID will be terminated on a Guest Anchor Controller inside Firewall DMZ. The Internal WLC controllers are installed with software versions 7.3.101.0, and the Guest Anchor controller is installed with software version 7.2.103.0. Just wondering if the Guest Anchor controller needs an upgrade to match the software versions on the HA controllers. Also, Cisco provides a new version of code, 7.3.112.0 now. So is it recommended to install the new software version on the HA controllers as well as the Guest Anchor Controller.
View 8 Replies
View Related
Mar 23, 2011
We have a WEB VPN running on Cisco ASA 5510 (SW = 8.2.1 / ASDM SW = 6.2.1). There are multiple internal (Web) applications are published on it and are working. One of the Web Application is working from internal network but from outside (or internet) through Web VPN, it is getting stuck and trying to load JAVA version. It is to be mentioned here, the latter web application is required Java Version 1.4.2 while the working applications are working with Java 1.5.1.
Is it possible to mount the more than on Java version on Cisco ASDM to be worked together ?
View 1 Replies
View Related
Feb 4, 2013
I have 2 laptops, one is running VISTA and one is running Windows 8. They are connected to my wireless router. I also have a desktop running Windows 7 that is wired to router. I have searched the internet and cannot find how to set up a new network without using a HOMEGROUP?
View 2 Replies
View Related
Sep 19, 2012
How can I find out the firmware versions for IOS, modules and components of Cisco catalyst 4500 series switch. I can see the firmware version of IOS in show version command but how can I find it out for the modules or components of the switch.
View 4 Replies
View Related
Jun 5, 2011
I used ASDM to upgrade a 5505 tonight and now I get the error message attached. How/where do I find out which versions are compatible?
View 2 Replies
View Related
Feb 19, 2010
I have many of these, many models and versions. I have a WRT54G v1, V1.1, V2....V8, I also have WRT54GS's WRT54GL's and others, Lots of other Linksys stuff, almost all of it in the Blue and Black boxes of varing sizes.I have a heck of a time when I reconfigure my network or the wife changes the furniture. I'd love a single document that lists the power specifications and adapter requirements for thens devices... I can't find them any where on the Linksys site. I Have looked and searched and nowhere can I find a consolidate list.
Any have a list of the DC power Specifications, Barrel sizes, and other stuff needed to buy a replacement Power adapter. This page url...lists a lot of information but does not list this critical information... I am amazed that Linksys does not have it listed some where here. Losing a wall wart should not be a reason to pull you hair out, just a simple purchase, If they don't want to stock them, then at least tell us what they are.
View 4 Replies
View Related
Feb 18, 2012
I have a problem with current (1.0.06) firmware on WRT120N. Few hours after restart DHCP server stops assigning IP addresses. Another restart resolves problem, but only for next few hours.Computers and other devices "see" my wireless network and they are able to connect to it, but the process stops at requesting IP number.There was no such effect with original firmware (although there was another problem with 2200BG), so I want to downgrade.where can I find previous versions of WRT120N firmware?
View 2 Replies
View Related
Mar 10, 2011
I've set up my wireless network and to the best of my knowledge it's safe and secure. However, I'm not 100% sure. Online totorial that'll show me how to Truly Make My Wireless Network Secure? I've got a dual-band Linksys router (model WRT320N).My Windows Vista laptop connects just fine. However, I can't connect my older Windows XP SP2.I think the reason why is because I only have one band of the router enabled?
View 3 Replies
View Related
Apr 6, 2011
just noticed today, that there's a FW ver.4.13 for Rev.D, which I uploaded into the router too. Captcha is now gone (I read it was flawed anyway), and no option to turn it back on (I'd do anyway).So I'm looking for the older firmware that I was using for a year or so, which was 4.11. I found it and downgraded to it (actually, this was on another DIR615 rev.D), and guess what? No catpcha in that either!As far as I remember, I was using 4.11-B04 (but not sure, really), whatever it means, and now I only find 4.11-B02 everywhere.Is it possible that those FWs with buggy captcha have been removed from FTP servers worldwide?
View 5 Replies
View Related
May 29, 2011
PoE works fine with C 1131/1141 Access Points and C-7975 IP phone but PoE does not seem to work on 7960 Phones nor on the C-1121 Access points
All devices work properly with the Cisco power injectors or on a Cisco Cat-29XX switch
Is there a trick to make PoE work for older devices ?
View 7 Replies
View Related
Oct 30, 2011
Recently my security has scanned all the network devices for vulnerabilities and found that cisco asa 5520 , which we use for RAS VPN has older version of openssl. Have to check that and fix this problem? FYI, recently we have installed a SSL cert for webmail users.
View 1 Replies
View Related
Oct 23, 2012
i am wanting to open up snmp on a pix 501 6.3 version. I am planning on doing it with the following configuration: [code]
I noticed you cannot specify RO on the snmp-server command with the older pix. I don't want this configuration to open up any write access to the pix. Is there a way to specify only read only for snmp
View 1 Replies
View Related
May 19, 2012
How do you find Clearwires ISP information to set up older 2.4 router?
View 1 Replies
View Related
Jun 12, 2012
Just got a new desktop computer (running windows 7). I'm using a DWA 125 dongle (DLINK) and connecting to a wireless router we just bought about 2 months ago...Now, I did a speed test (www.speedtest.net) with the desktop computer... I'm getting about 8 mb/sI did one with my older latop (intergrated wi-fi)... I'm getting like 17 mb/s ??
View 2 Replies
View Related
