Recently my security has scanned all the network devices for vulnerabilities and found that cisco asa 5520 , which we use for RAS VPN has older version of openssl. Have to check that and fix this problem? FYI, recently we have installed a SSL cert for webmail users.
View 1 Replies
i went through the website and figured that my firmware is 1.01.05 and there's a new version availble which is 1.01.09 for my Linksys WAG200G modem since im having problem with unstable connection and now, after i updated the firmware, not only that im dropping connection heaps more, my internet connection has slowed down by alot.
View 2 Replies View RelatedI have a number of existing 4506 chassis type switches (the older non -E version) that I would like to roll out IP phones to. Instead of replacing the entire chassis, I would like to just replace the line cards in the switches with WS-X4548-GB-RJ45V. What or how much power supplies should I have in each switch to be able to power the 5 poe line cards (each port per line card will power an ip phone)?
View 6 Replies View Relatedprovide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View RelatedWe want to make an upgrade of one of our customers' ASA 5520 (with failover). They have version 8.2 now and we want to get the more stable newest one. Can we get an 8.6 version? or we need an ASA 5500X for that one?
View 2 Replies View RelatedI have a server in a DMZ behind the ASA, connections to this server work sometimes and then fail others, so I dont think i'm looking at an ACL or NAT problem here.The syslogs report a SYN Timeout,I have taken a trace on the ASA, it seems that a SYN-ACK does come from the destination server within the 30sec timeout, but its not passed through the ASA back to the source ? there is one odd thing, what seems to be an out of sequence ACK from the destination which arrives before the SYN-ACK at the ASA, i'm wondering if this might be the problem ? This only occurs on the connections which fail, the connections that work, the destination responds quickly to the initial SYN, and the 3way handshake completes.
Syslogs :
Oct 18 19:17:32 nzlsudfedsi001-pri Oct 18 2011 19:17:32 NZLSUDFEDSI001 : %ASA-6-302013: Built outbound TCP connection 42327212 for IIP-ARCHIVE-PROD:172.24.32.31/21 (172.24.32.31/21) to BPO-TRANSIT:x.x.x.x/59392 (x.x.x.x/59392)
Oct 18 19:18:02 nzlsudfedsi001-pri Oct 18 2011 19:18:02 NZLSUDFEDSI001 : %ASA-6-302014: Teardown TCP connection 42327212 for IIP-ARCHIVE-PROD:172.24.32.31/21 to BPO-TRANSIT:x.x.x.x/59392 duration 0:00:30 bytes 0 SYN Timeout
[code].....
McAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies View RelatedCan we use ACS 4.1 version recovery disc on 4.2 verison to recover the forgotten password.
View 1 Replies View Relatedwhich version of prime infrastructure supports wlc5508 version 7.4
View 2 Replies View RelatedI've set up my wireless network and to the best of my knowledge it's safe and secure. However, I'm not 100% sure. Online totorial that'll show me how to Truly Make My Wireless Network Secure? I've got a dual-band Linksys router (model WRT320N).My Windows Vista laptop connects just fine. However, I can't connect my older Windows XP SP2.I think the reason why is because I only have one band of the router enabled?
View 3 Replies View Relatedjust noticed today, that there's a FW ver.4.13 for Rev.D, which I uploaded into the router too. Captcha is now gone (I read it was flawed anyway), and no option to turn it back on (I'd do anyway).So I'm looking for the older firmware that I was using for a year or so, which was 4.11. I found it and downgraded to it (actually, this was on another DIR615 rev.D), and guess what? No catpcha in that either!As far as I remember, I was using 4.11-B04 (but not sure, really), whatever it means, and now I only find 4.11-B02 everywhere.Is it possible that those FWs with buggy captcha have been removed from FTP servers worldwide?
View 5 Replies View RelatedPoE works fine with C 1131/1141 Access Points and C-7975 IP phone but PoE does not seem to work on 7960 Phones nor on the C-1121 Access points
All devices work properly with the Cisco power injectors or on a Cisco Cat-29XX switch
Is there a trick to make PoE work for older devices ?
i am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View Relatedi am wanting to open up snmp on a pix 501 6.3 version. I am planning on doing it with the following configuration: [code]
I noticed you cannot specify RO on the snmp-server command with the older pix. I don't want this configuration to open up any write access to the pix. Is there a way to specify only read only for snmp
I have some legacy (read: old) audio equipment that used leased lines to run, no way to convert them to IP internally. They have x.21 and v.35 interfaces on them.
Is there a way i could use something like an old 2600 series router and run it in reverse, like just using them as a media converter to shove the v.35 over into IP land?
I'm not interested in buying newest latest greatest (these audio codecs are upwards of $5k a pop to replace, x2 for a complete link), i'm just curious if i can turn a WIC-1T into the interface for these boxes and do a direct route to another 2600 on the other end with the same configuration.
This would essentially turn the WIC portion into the local side and the ethernet into the WAN side.
We have several RV042 routers with older firmware version 1.3.12.19-tm.We have purchased new RV042 routers as hot spare replacement that's coming with firmware version 4.1 installed.
We have a VPN tunnels between multiple sites using the older firmware version.
My question is: Will a RV042 with firmware version 4.1 connect to a RV042 with firmware version 1.3.12.19-tm and vice versa?
How do you find Clearwires ISP information to set up older 2.4 router?
View 1 Replies View RelatedJust got a new desktop computer (running windows 7). I'm using a DWA 125 dongle (DLINK) and connecting to a wireless router we just bought about 2 months ago...Now, I did a speed test (www.speedtest.net) with the desktop computer... I'm getting about 8 mb/sI did one with my older latop (intergrated wi-fi)... I'm getting like 17 mb/s ??
View 2 Replies View RelatedMy customer had a spare ASA5510 bought a few years before with 5 x FE and security plus license with HA. Now they would like to buy a new ASA5510 to configure HA with the spare one, but now the ASA5510 comes with 2GE+3FE. Can the two FW work in HA?
View 4 Replies View RelatedI have an existing setup of older 1242AG-E-K9 access points with Air-ANT-ANT5160 antennas connected to them. Goal is to replace old AP's with new AIR-LAP1262N-E-K9 model. Question is that can I use only one antenna per radio? Does it work? I know that N-standard requirement is 3 antennas per radio (3 x 2.4G and 3 x 5G) but we need only B/G to work. Plan is to re-use existing AIR-ANT-ANT5160's and order new AIR-ANT2506 antennas. Setup per AP would be 1 x 2.4G and 1 x 5G.
View 7 Replies View RelatedWe have a CISCO RV042. We are about to begin a VIOP service with Vocalocity who state:
The RV042 is a wired router that requires no configuration adjustments for the firmware versions we tested. Version 1 and 2 are compatible. Version 3 is NOT. Firmware Reviewed: 1.3.12.6 | 1.3.12.19
Our router's firmware is : 1.3.8.2 (Feb 12 2007 10:43:08)
Can we upgrade to 1.3.12.6 or 1.3.12.19? What is meant by Version 1, 2 and 3?
I'm putting together a lab to start on my CCNA and I've got two 3640s and two 2620s. I want to upgrade all of the units before I start on the CCNA and I'm having trouble working out what the final rommon version is for each of the routers.My 3640's are on version "Version 11.1(20)AA2". Is this the final release ?
One of my 2620's is on "Version 12.2(10r)1" and the other is on "Version 12.2(6r)". Is "10r" the final release for the 2620 ?I've also seen a few sites mention that either version "8r" or "3r" of the 2620 rommon adds support for 32MB flash SIMMs. Is that correct ?Is there a document that describes the differences between the different releases ?
I have a ACL applied on a WLAN on a 2125 controller. I cannot get the older Cisco IPSec (Version 5.0.05.0290) client to work through the ACL and through the WLAN onto it's destination. When the Cisco IPSec client is on another unrestricted WLAN, it works. I have allowed TCP/UDP 500, 4500, TCP 10000 both directions and it fails. I can see the denys counters incrementing but cannot figure out what is being blocked.
View 1 Replies View RelatedI have an old Cabletron switch i have used for about 8-10 years, it has some vlans set up and i was wondering how i can "talk" to the switch and set it up. I am using this switch in my home on my vast network. is it possible to "reset to factory" or anything without a serial cable? I would like to use snmp of telnet to configure but i dont think it has an ip set up and it is such an old switch I cannot find any info from entrasys.
View 1 Replies View Relatedhave older laptop vista no picture blank screen new laptop window 7 can i hook them together
View 1 Replies View RelatedI purchased a new laptop (wireless-n). However, the old laptop I have from 6 six years ago (wireless g) has a faster wireless connection than the new one (20-25 mbps vs. 0.50-1.00 mbps). The 2 computers are at the same location in the house in regards to the router.
View 12 Replies View RelatedLooking at getting an older second computer onto the internet. We have a wireless connection on the primary computer so I was looking at the TP-Link TL-WN321G USB network adapter, or the TP-LINK WN350GD PCI network adapter.The end goal of course is to get the old computer onto wireless, but not sure what the best way to do it is. I'd think the motherboard would accept the PCI card though we do somewhat lack USB facilities. The computer uses a USB hub which I'm not sure if it would impact on internet speeds at all.
View 3 Replies View RelatedI am trying to configure an older Belkin Router (Model Number 5FD8230-4) as an Access Point so that I can boost the range of my network. The problem I have is in configuring the old router. It won't allow me to change any settings, or at least the changes don't stick, even after clicking "apply changes". I tried creating an administrative password but I am not even sure that this is working. I am using a Macbook, so perhaps this is an Apple compatibility issue. I have tried resetting the router and reverting to Factory default settings, but no joy.
View 3 Replies View RelatedI have an iMac running 10.4.11. I would like be able to print through the router. I now have my PC laptops doing so. What voodoo do I have to do to make the iMac work with it?
View 3 Replies View RelatedI want upgrade IOS on my 7206VXR from 12.4(12c) to 15.1(4)M5 , but the CF card only 64M.
-NAME: "disk2", DESCR: "64MB Compact Flash Disk for NPE-G1"
-Router#show bootvar
BOOT variable = disk2:c7200-jk9s-mz.124-12c.bin,15.1(4)M5 is almost 40M. So there is not enough space.I want to ask is it ok if I upgrade with normal precedure , With the command " copy tftp: disk2: " ?Does the router will automatically delete the older IOS first and then copy into the new one ? Or Is there something I should pay attention first ?
We have had an active ACS unit for many years now, and we've added a second one, both are 1121 Appliances. The newer one came with 5.4, so we upgraded the older one to 5.4.
We setup replication between the two, with the newer one primary and the older one secondary. Problem is, windows based clients are unable to authenticate to the older ACS appliance. The only problem we can see is that it indicates that adclient is not running, under Monitoring & Troubleshooting, ACS Health Instance Summary.
So... been trying to figure out how to correct this, yet have been hard pressed to find a knowledgebase article that works. So far, Cisco hasn't added my smartNet on the new box so I can get some support?
I am in the process of swapping out an older 24 port Cisco catalyst 3525 POE switch running IOS 12.0(5) with a 48 port POE catalyst 3560 running ios 12.2(50)The trunk port on the older switch (that currently works) is in port Gig0/1 with as basic of a trunk config as you might find.
In the newer switch I have a 1000BaseSX SFP min gbic with a SC-LC fiber cable attached (8.3/125 – 15 meter.When I make the connections, I get no lights… no connection.
I have an older Dell laptop (Inspiron 4150: 10+ years old) and it has an onboard 3com 10/100 ethernet adapter. I recently switched to a Doccis 3.0 modem from Comcast and the laptop doesn't seem to get along with it too well. Are there any options for me to be able to get a Gigabit ethernet adapter for this older laptop? As far as the expansion slots go, the laptop has a Cardbus controller (Texas Instruements 1420 Cardbus controller) and as far as the PC Card connectors go, it has 2(supports 2 Type I or II cards or 1 Type III card with the PCMCIA being 16 bits and the Cardbus being 32 bits).
Is there such thing as a Gigabit ethernet pc card that this laptop would support? If not, what other options are there?
