Cisco :: Config Lawful Intercept Failed On 7600

Feb 1, 2012

I have to config Lawful Intercept on 7600, IOS version 12.2(33)SRC6. Every step have be taken by "Cisco 7600 Lawful Intercept Configuration Guide".Such as: [code] So, config failed? or these objests should be created? or something?

View 2 Replies


ADVERTISEMENT

Cisco :: LMS 4.1 Config Archive Is Failed For Around 20 Devices

Jul 28, 2012

We have LMS 4.1 with more than 150 devices.Config Archive is failed for around 20 device.
 
11- Cisco VG248 ( Cisco analogue gateway)
7  - Cisco call manager
2 - Wireless Lan controller
 
For this device-  discovery, Inventory Collection ,Fault Discovery,  Topology Data Collection ,etc are successfull.

View 3 Replies View Related

Cisco WAN :: Catalyst 6500 - Lawful Interception Sip-401 And Sip-200

Feb 21, 2011

Does SIP-401 module for 12000 series router supports LI IOS software, or  that function can be activated only with sip-600. Can I run Lawfull Interception with sip-401  module on 12406 router ??
 
and can SIP-200 module for Catalyst 6500 run lawfull interception ios and be used for that purpose ???

View 1 Replies View Related

Cisco Firewall :: ASA 5510 Can't Inspect And Intercept For HTTPS Traffic

Feb 23, 2011

I want to block some social networking sites using ASA 5510-CSC-SSM, As I searched and come to know that ASA 5510 can't inspect and intercept for https traffic because it is encrypted while traversing throught the ASA. I want the ASA to make functioning for https too, not only http. Can i perform this task by updating any software on existing device?

View 2 Replies View Related

Cisco Switching/Routing :: ASA 5505 Upload Config File Into Start-up Config

Apr 17, 2012

If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?

View 5 Replies View Related

Cisco WAN :: 2811 - Startup Config Is Not Copying To Running Config

Nov 15, 2009

I have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.

router#copy start-up running-config

View 9 Replies View Related

Cisco Switching/Routing :: 3845 - License Installation Failed With Error / XML Parsing Failed

Jan 19, 2012

I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it  i am facing the error "% Error: License installation failed with error: XML parsing failed".

View 4 Replies View Related

Cisco WAN :: IOS From Sup 720 To RSP 720 In 7600?

Jan 31, 2013

i have a query ,we are planning to upgrade the Sup Engine from WS-SUP720-3B 2 ports Supervisor Engine 720 to
 
RSP720-3CXL-GE=

Cisco 7600 Route Switch Processor 720Gbps fabric,PFC3CXL, GE
  
Can we use the same old IOS from Sup720 to the New RSP720 without purchasing it ?
 
Show  Version-- Cisco Router 7609
 
Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB3, RELEASE SOFTWARE (fc1)ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
 
System returned to ROM by  power cycle at 08:36:39 PDT Fri Mar 30 2007 (SP by power on)
System restarted at 10:04:20 GMT Fri Nov 25 2011
System image file is "bootdisk:c7600s72033-advipservicesk9-mz.122-33.SRB3.bin"
Last reload type: Normal Reload

[code]....

View 3 Replies View Related

Cisco WAN :: What Is SPA / SIP In 7600

Jan 19, 2012

what is use of haiving SPA and SIP in router hardware ? what if we dont have them in router ?

View 3 Replies View Related

Cisco WAN :: 7600 - Upgrade IOS From 12.2(18)SXF To 12.2(33)SRC?

Mar 6, 2011

I need to know if upgrading Cisco IOS on 7600 series router is possible. From 12.2(18)SXF --> 12.2(33)SRC, i need this because SRC supports Lawfull Intercept. 
 
specification of router is 7606
slot 1 - WS-X6708-10GE
slot 1/0 - WS-F6700-DFC3C
slot 4 - WS-X6408A-GBIC
slot 6 - WS-SUP720-3B
slot 6/0 - WS-F6K-PFC3B
slot 6/1 - WS-SUP720

View 1 Replies View Related

Cisco WAN :: X.25 And Xot On Router 7600

Dec 5, 2012

The 7600 platform support x.25 and XOT features. In ios versión S764AEK9-15103SCisco   7600-RSP720 IOS ADVANCED ENTERPRISE SERVICES SSH The feature navigator display that support this features, but i'dont see these on the other newer ios version. If posible use 7600 for x.25 / xot or maybe will used de 3900 platform?

View 1 Replies View Related

Cisco WAN :: Configure SIP For 7600?

Jan 19, 2012

If I have SIP-200 and I need to configure a feature , for eg - PPP on SIP-200 , is it something possible ? If Yes how I can do that in IOS ?

View 1 Replies View Related

Cisco WAN :: PBR Usage With 7600

May 16, 2012

Today i want to ask is cisco 7600 support ip next-hop recusrive x.x.x.x (PBR feature).

View 1 Replies View Related

Cisco WAN :: PBR On 7600 Not Implemented In H / W

Nov 19, 2011

Why below simple PBR is not implemented in H/W knowing the Copp is not configured
 
NPE-1#sh ver | i image
System image file is "bootdisk:c7600rsp72043-advipservices-mz.122-33.SRE0a"
 NPE-1#sh run int GigabitEthernet1/1
interface GigabitEthernet1/1
ip address 11.0.0.1 255.255.255.0
ip pim sparse-mode

[code]...

View 4 Replies View Related

Cisco WAN :: 7600 Cannot Get BGP Keepalives

May 11, 2011

I am trying to establish a BGP session between a Cisco 7600 and Juniper MX960, but this always stucks in OpenConfirm state.
 
access-4#show ip bgp v v VRF1 neighbors 166.63.168.197BGP neighbor is 166.63.168.197,  vrf VRF1,  remote AS 5555,  local AS 65533, external link  BGP version 4, remote router ID 195.2.1.21  BGP state = OpenConfirm  Last read 00:02:27, last write 00:02:27, hold time is 180, keepalive interval is 60 seconds  Message statistics:    InQ depth is 0    OutQ depth is 0                         Sent       Rcvd    Opens:                  4          4    Notifications:          2          1    Updates:                0          0    Keepalives:             4        
 
May 12 13:58:07.531 bst:     TCP src=54912, dst=179, seq=1766275951, ack=1681278050, win=17520 ACK PSHMay 12 13:58:07.535 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:53.883 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:59.359 bst: IP: s=166.63.168.197 (Vlan20), d=166.63.168.198, len 61, rcvd 2May 12 13:58:59.359 bst:     TCP src=54912, dst=179, seq=1766276010, ack=1681278050, win=17520 ACK PSH FINMay 12 13:58:59.359 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:59.359 bst: %BGP-3-NOTIFICATION: received from neighbor 166.63.168.197 4/0 (hold time expired) 0 bytes
 
ICMP works fine. It is same on JUniper end. Sending keepalives but cannot receive
 
###interface configinterface Vlan20 ip vrf forwarding VRF1 ip address 166.63.168.198 255.255.255.252 no ip redirects no ip proxy-arp load-interval 30end
 
###bgp config
neighbor 166.63.168.197 remote-as 5555 neighbor 166.63.168.197 local-as 65533 neighbor 166.63.168.197 ebgp-multihop 5 neighbor 166.63.168.197 update-source Vlan20 neighbor 166.63.168.197 activate neighbor 166.63.168.197 soft-reconfiguration inbound

View 1 Replies View Related

Cisco WAN :: VS-S720-10G-3C On 7600?

Nov 5, 2012

I am pretty far out of my comfort zone here but these VS-S720-10G-3C cards were purchased to upgrade our 7609/7606 routers, the spec sheet says they are compatable but I can't find an IOS that "likes" them. I had no problem finding an IOS and using the vss cards in our 6506...

[URL]

View 3 Replies View Related

Cisco Infrastructure :: What Is SPA / SIP In 7600

Jan 19, 2012

what is the use SPA and SIP...in router hardware ? What if we do not have them ?

View 1 Replies View Related

Cisco WAN :: 7600 - QoS On Sup720?

Oct 16, 2012

I have a strange QoS problem with one Cisco7600 (sup7203BXL, IOS 12.2(33)SRE6).
 
This is layer 2 traffic,and all ports are L2 dot1q trunks:
 
1) Packet comes with DSCP 46 on Gigabit port (WS6728-SFP) with "mls qos trust dscp" configured. It goes out the port of the same card/slot with DSCP 0.
 
2) packet comes with DSCP 46 on different Gigabit port on the same card/slot with "mls qos trust dscp" and also "mls qos vlan-based" configured. It qoes out out the port with DSCP 46.
 
Why the switch behave differently if "mls qos vlan-based" is configured on port (or to say it works correct since it doesn't override DSCP)?
 
I have global command "mls qos rewrite ip dscp" since this 7600 is also MPLS PE router and I found in documentation that "mls qos rewite ip dscp" is mandatory for QoS on MPLS (EXP bits). So I can't turn off "rewrite ip dscp". Again the problem that I presents is L2 problem not MPLS (MPLS is used for different traffic).
 
Also mls qos mappings are ok COS to DSCp are 5 to 46 and vice versa.
 
Furthermore, as far as I know if I have configured "mls qos trust dscp" on Gigabit ethernet port, switch (7600) should work in this order:

- make internal DSCP from packet DSCP

- since I don't have configured DSCP mutation DSCP should stay the same (46)

- using map DSCP - COS ( 46 -5 ) switch will choose queue on outgoing interface in regards to mapped COS

View 0 Replies View Related

Cisco :: IP SLA / Ethernet OAM On 7600 Series

Jan 14, 2013

I'm looking for iformation if CFM Local Maintenance End Point configured on Cisco 7606 router is able to respond to the Y.1731 Performance Monitoring (DMM/DMR ).I know I can use IP SLA to configure Y.1731 PM measurements, but I just need a reflector that will answer for incoming DMM messages with DMRs.

View 0 Replies View Related

Cisco WAN :: Configuring EoMPLS In 7600?

Mar 20, 2012

You can configure EoMPLS on a port of the WS-X6724SFP card found in a Cisco 7600 with Supervisor 720.

View 1 Replies View Related

Cisco WAN :: 7600-SIP-200 Module In VSS Mode

Mar 26, 2011

if the  7600-SIP-200 supported in VSS mode or not ?
 
I have configured to Cisco Catalyst 6513 as VSS, both of them have the 7600-SIP-200 module, before converting them to VSS I was able to work with the 7600-SIP-200 module, but after I did convert them to VSS, both modules didn't work.
 
here is the show module output, after VSS conversion:
 
VSS1#show module Mod Ports Card Type                              Model              Serial No.--- ----- -------------------------------------- ------------------ -----------  1    0  4-subslot SPA Interface Processor-200  7600-SIP-200       JAE14500GMT  7    5  Supervisor Engine 720 10GE

[Code].....

View 1 Replies View Related

Cisco WAN :: 7600 Sip 200 Log Message Meaning

Oct 22, 2012

Need to clarify this log message:

*Oct 23 06:20:07 UTC: %FPD_MGMT-3-INCOMP_IMG_VER: Incompatible ROMMON (FPD ID=5) image version detected for 7600-SIP-200 card in slot  Detected version = 1.3, minimum required version = 1.4. Current HW version = 2.303.

View 1 Replies View Related

Cisco WAN :: Performance For 7600 / 6509 With SP-720

Dec 7, 2010

I  would like more information of performance to 7600 router with the  SP-720, how many sessions full bgp routing it  supports? I have 4 links 1 GB and a throughput of 900 MB.

View 4 Replies View Related

Cisco WAN :: Bandwidth Limit On 7600?

Apr 29, 2012

I have cisco 7600 core router in ISP , i want to put the bandwidth limit on it for outgoing traffic (for internet) on a subnet because i am using Bluecoat and i want to test my bluecoat.On this subnet i have no limit for bluecoat but after the bluecoat i want to limit it. On 7600 cisco router i have not rate limit command so how it can be possible for a perticular subnet ?

View 1 Replies View Related

Cisco Infrastructure :: 7600 - SIP-400 Not Powering Up?

Oct 10, 2011

I have a 7606 running c7600rsp72043-advipservicesk9-mz.122-33.SRD2.bin with SIP-400 card that has suddenly stopped working, on checking the logs i see the following:
 
%ONLINE-SP-6-TIMER: Module 3, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 3 set off (Module  Failed SCP dnld)
 
I have tried reseating and even moving it to a different slot but no luck.
 
%ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 4 set off (Module  Failed SCP dnld)
 
sh module
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1   20  ESM20G                                 7600-ES20-GE3C     JAE1237UT90
  2    4  7600 ES+                               7600-ES+4TG3CXL    JAE13157HIW
  3    0  4-subslot SPA Interface Processor-400  7600-SIP-400       JAE13219CZH
  5    2  Route Switch Processor 720 (Active)    RSP720-3C-GE       JAE1151819I
  6    2  Route Switch Processor 720 (Hot)       RSP720-3C-GE       JAE11495POH

[code].....

View 4 Replies View Related

Cisco :: 7600 DFM Alerts Operationally Down

Nov 2, 2012

im having lms 4.2.2 and monitoring a cisco 7600 router interface ten gigabit ethernet x/x under dfm. When ever the interface is down due to any media issue i am not getting any alerts in dfm., the interface used to go down for more than 10 minutes. I am able to do an snmpwalk to this interface when the interface was down and getting the value as 2(for down). I am getting other information and configuration mode alerts in dfm for this device.

View 1 Replies View Related

Cisco WAN :: 7600 - BGP Route Reflectors

Oct 14, 2011

I posted also under Service Providers for my problem with MPLS/VPN. I just noticed I have the same issue with plain IPV4 BGP. [URL] I have two 7600 running on SRC3 and SRD6. Both acting as RRs.
 
I noticed that RR1 is reflecting the route to this other 7600 iBGP peer but not installing/importing the route. Other iBGP speakers are able to install and import the route. Is there any issue with 7600 SRC/SRD IOS for Route-reflection?
 
iBGP policy is similar to all but only the 7600 is unable to install the route. Other 7200 ibgp peers are successful.

View 1 Replies View Related

Cisco WAN :: 7600 - RSP Reload Continuously?

Jan 14, 2011

Router with 2 RSP RSP720-3C-GE & Image: c7600rsp72043-advipservicesk9-mz.122-33.SRE2.bin We are getting the message as
 
------------------ show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRE2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]

[Code]....

Show log is attached & we are getting %DHCPD-4-DECLINE_CONFLICT: messages constantly.

View 6 Replies View Related

Cisco WAN :: 7600 TDM Cross-connect?

Oct 11, 2011

I'm trying to find a single device that can both handle Q-in-Q VLAN trunk termination and also TDM cross connects between DS0's on a multi-channel T1 card and DS0's on a multi-channel DS-3 card.  I'm looking at a Cisco 7606-S with SUP720's.  If I install a 7600-SIP-200 or 7600-SIP-400 with both a SPA-2XCT3/DS0 (channelized T3 card) and a SPA-8XCHT1/E1 (channelized T1 card) will I be able to TDM cross connect the DS0's between the cards?  Is there a limit on the number of TDM cross connects?  Also, I noticed the CMM cards are EOL.  Ideally we'd like to terminate PRI's into the 7606 and run H.323.  We'd like to pass voice calls to CUCM and TDM switch FAX calls (via H.323 dial-peer) to a given CAS DS0 on the SPA-2XCT3/DS0.  Is this doable with any of the current cards?  If not, then we'll stick to the configuration in the first paragraph and only have the 7606 handle the TDM cross connects.

View 3 Replies View Related

Cisco WAN :: QoS On 7600 Series Router

Oct 18, 2012

I am looking for the best QoS method for a 7600 series router. We have a 7604 edge router that has remote branch connections to it via GRE tunnels. unfortunately I cannot shape on these GRE tunnels neither can I use bandwidth or priority statements.

View 1 Replies View Related

Cisco WAN :: 7600 Card Not Supporting Qinq

Dec 5, 2012

I want to do qinq on this card under its sub-interface, unfortanately it doesnt support the command as compared to other ES cards. [code]

View 3 Replies View Related

Cisco WAN :: 7600 - Limitations Of NetFlow V9 Support

Apr 23, 2012

What are the limitations of Net flow v9 support on the 7600 platform for the SR code releases?
 
I know that Flexible Net flow is only available on newer releases with some newer hardware.   Flexible Net flow gives you the ability to provide full support for Netflow v9 as well as IPFIX.  
 
However, the documentation indicates that Net flow v9 is still supported in the SR code.   So I am just trying to find out what are the limitations in how Net flow v9 is implemented without "Flexible Net flow".   The Cisco TAC was unable to provide me any documentation about this.

View 1 Replies View Related

Cisco Switching/Routing :: 7600 SIP-400 MIB Required

Apr 14, 2010

I have Cisco 7609 router and we have observed that router is rebooted due to the following error ;SLOT 3: Apr 13 16:06:26.621: %CARDMGR-2-ESF_DEV_ERROR: An error has occurred on Egress ESF Engine: Control Store Parity Error SLOT 3: Apr 13,Slot -3 we have SIP-400 card. We would like to know if there is any MIB which can monitir such reboots.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved