Is there anyway to force the xbox inside the router to grab the same ip address everytime it comes on? Other than changing it on the console via a static ip? Xboxs dont like static Ip address and its getting annoying?
View 11 Replies
I've been using the Dir-655 for 2 or 3 years with my old Xbox 360 and an external G wireless adapter. Everything was working perfectly until I got the dreaded Red Rings Of Death the other day. I replaced the Xbox with a new Slim version with built in N capable network adapter.
After more than 10 hours of trying a variety of "fixes" I found from MS and in this forum, I am still at square 1.
Hardware Version : A3
Firmware Version : 1.32NA (this is listed as Live compatible by Microsoft)
802.11 Mode : Tried N only, G only and mixed 802.11n and 802.11g
Enable Auto Channel Scan : Checked
Transmission Rate : Best (automatic)
Channel Width : Auto 20/40
Visibility Status : Visible
Security Mode : WPA-Personal Also tried WEP
WPA Mode : Auto (WPA or WPA2) Also tried WEP
Cipher Type : TKOP and AES
I tried assigning an IP manually from the Xbox. But, no matter what I do, the router will not accept it. It is especially frustrating that the Xbox is visible to the unit. It simply will not assign an IP to it under any circumstance.
If you read the sales hype promoting the Dir-655, you will see a lot of nonsense about it being great for gaming. Given that, you'd think a simple solution would have been found and posted for this issue by now. Surely, end users shouldn't be trying 100 different possible "fixes", none of which work, at this late stage of the firmware upgrades. If I sound a tad fed up, it's because I am. After the expense of the new Xbox, it appears I now have to junk my router too.
Here is the status screen taken when it was in mixed mode. Changing it to 'G Only' didn't make any difference:
I've set up a DHCP reservation on a Netgear wpn824v3 router, using its "Attached Devices" list to specify the MAC address of a computer on the network to use IP 192.168.5.200. After using "ipconfig /release" then "ipconfig /renew" on the client PC, though, the client PC keeps going back to the address it got automatically, i.e., 192.168.5.3.How can I force the client to use 192.168.5.200?
View 1 Replies View RelatedIve been trying to work this out on XBL forum for a while. all my settings seem to be correct ( UPnP, NAT type: open, no port forwarding or triggering, IP settings on Xbox's are auto).
The two Xbox can play online separately, when either one of them attempts to join the others party it disconnects from Xbox live.
According to the microsoft website, Xbox live only supports the Hardware version 1A and Firmware: 1.00NA.
My router has B1 and 2.00NA. is there a way to downgrade?
I can't use both online for some reason. I also can't get my 360 to work online unless I reset my router, and the IP says something like 24.* whatever in the network settings for the 360. I'm fairly knowledgeable about computers, but I barely know anything about networking so bear with me. I think this started after I removed a cable from my router (a different connection that I didn't need any more), and hit the reset button. I'm not sure what exactly it changed to cause this however. I also tried a router of the exact same model and it didn't work.
View 9 Replies View RelatedMy son connects his xbox360 to his laptop that uses a wireless access to the router. My husband and i both have a laptop and when we try to log on to the internet it takes forever or doesn't connect at all while son is on his xbox 360. Do I need to change up my router?
View 1 Replies View RelatedI have a LAN port cable, and I have one end connected to the back of my router.Where does the other end go, so I can receive wireless internet connection of both my Toshiba Satellite Laptop, and Gateway Desktop. First I had the LAN port cable connected at the back of my router, and the other end was connected at the back of my desktop. A little green light lit up at the back of my desktop, saying that it was grabbing signal. I could use the internet fine, and my laptop could grab wireless signal fine as well. I was missing around my router, trying to see what mark it was, and the LAN port cable came off, and when I plugged it back in, i couldn't receive signal, and neither could my laptop. Now the only way I can grab signal is by connecting the WAN port cable from my modem to my desktop, which means I cant get wireless signal on my laptop. Now when I do connect my LAN port cable to the back of my desktop, I try connecting to my wireless connection, and when I go to Network and Sharing Center, it says Connected (With full bars).
View 1 Replies View RelatedI have CiscoWorks 3.1.
1. When creating job or log file, these files are always stored in the default Path (inside LMSROOT) for RME for example...Could I change RME default Path to store these files in another location inside the Hard Disk?
2. Could I Configure CW-LMS to send all the reports to me by mail?
3. What is the Difference between Poll Interval time and Collection time inside RME?
I have a DIR-600 C1 running the latest available firmware version (3.03).
Model: DIR-600
Hardware Version: C1
Firmware Version: 3.03
WiFi Protected Setup is turned ON.I would like to know if it is affected by the new disclosed vulnerability described here:[URL] Also, turning WiFi Protected Setup OFF may not assist to mitigate this vulnerability?
Is this router good for gaming with the Xbox 360 & PS3.My linksys wrt120 n is giving me fits I need a better gaming router.
View 2 Replies View RelatedI'm having trouble seeing my PC from my XBox (I want to use WMC to stream video to XBox). Here's my setup:
ISP provided modem (No branding), connected to my PC Network out (Wired) from modem to Dlink DIR-665 router (which is broadcasting WIFI) Network out (Wired) from Dlink router to XBox
I'm online with the XBox with no issue, but I can't access the PC through Media Centre with this setup. When I connect the XBox to the modem directly, I also have no issues. I'm using Norton Internet Security 2012 if that could be the issue.
Until yesterday my various equipment was networking to each other and the internet without a problem. After i reset my d-link DSL-2640B router (would this initiate an update?) my x-box would not connect to the internet, There is no problem connecting to the router and the home network. Everything is talking to each other and everything else is connected to the internet including the TV. The router must just be blocking the x-box and only from yesterday. I checked ports that are talked about and i think i set up port triggering, but then noticed the firewall is disabled anyway.
View 10 Replies View RelatedAI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies View Relatedi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
i need to find the ip address for my xbox
View 1 Replies View RelatedI travel alot so to break up the boredom at the hotels i like to play on my xbox what would make it a whole lot more fun would be to play with my friends online. Problem is that my xbox does not have built in wifi and even with a wifi adapter hotel internet portals prevent from connecting automatically to internet without a browser. I have watched some video on youtube with different methods of using a laptop to connect via ethernet to your xbox and share the internet connection from the laptop. Is there a method that works with Vista? I keep getting a unable to get an ip address error on the xbox and not sure as to what to do.
View 3 Replies View RelatedSet my DIR-655 to limit my son's time on the Internet. I have all the connections set to the MAC Addresses
View 4 Replies View RelatedI starting having really bad lag when playing games or just surfing. I put on wireshark and can see my router is broadcasting all the time. here is part of the wireshark log
"1","0.000000000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.172? Tell 192.168.0.1"
"2","0.000737000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.171? Tell 192.168.0.1"
"3","0.001469000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.170? Tell 192.168.0.1"
"4","1.002284000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.169? Tell 192.168.0.1"
it does this for the whole subnet then starts over. i turned off all the broadcasting in all the menu and it still doing it. i upgraded to 2.10NA, but it did not seem to do anything to it. I bought this router on 3-5-11. I have not tried resetting it to factory settings. I wanted to see if i missed something first. Router is on a APC UPS with the modem and the switch.
Hardware version is dir-655 B1
firmware is 2.10NA
cox cable is my ISP
Is there anyway you can assign a static IP address within WAG160Nv2 to peripherals such as an XBOX?
The knowledge base only seems to show how to assign an IP address in the XBOX but when I have to reboot the router, I've noticed the XBOX is assigned a new IP address when viewed in the router pages.
If I set a permanent IP address in the XBOX, this will no longer match what is in the router.
My customer has a 5510 with the inside interface connected to a routed port on a Cat3560G.When I look at the arp cache on the 5510 all inside IPs have the MAC of the 3560's routed port. [code]
View 6 Replies View RelatedI am using 2 vpn-routers RVS4000, to interconnect 2 hybrid telephone IP-PBX. After configuring the VPN the head offices are not seen in network. The VPN is active in windows.
IP-PBX works correctly in te same LAN. I understand that the problem is that I do not find how to indicate the router to send de UDP packets to the correct IP thought the VPN.
I guess I'll start with the easy stuff, Cisco ASA 5520 ver 8.2, ASDM ver 6.2, IPSec L2L tunnel with overlapping private IPs.
I have about a dozen L2L connections on our 5520 but never had to do one with overlapping IPs. I have two that I have to build and one definitely overlaps our inside locals, and the other is requesting that we NAT our inside locals to a 10.x.x.x.
I've searched the board and found several good posts including document 112049, but I just don't seem to be able to get my head around how to translate one inside address to another. It would seem like is would be as easy as doing an (inside,inside) static NAT, but most everything has the solution as a policy NAT or doing an (inside, outside) but in the less secure address space place the name of an ACL. I have ordered that brick of a book on ASAs from Cisco Press, but need to get something going and I'm not having much luck getting this thing up and running.
Perhaps my basic understanding of NAT rules is wrong. I thought that when using NAT the command speaks to the interfaces and the direction of travel, (inside,outside). I also thought that the IP adresses used must be valid on the interface refferenced, so any refference to "inside" would have to be an address on the "inside interface of the FW and likewise for the "outside" interface. Finally, to be sure I'm not calling a duck a goose my understanding is that the following are correct; "inside local" = my private, "inside global= my peer, "outside local"= their private, "outside global"= their peer.
So if I'm translating say a 192.x.x.x on my inside local and wanted to present them a 10.x.x.x, wouldn't I need an (inside,outside)? And even though I'm translating my private IP into a different private IP, the translated IP must be on the "outside" interface because that is the interface that I want to present the new private IP on?
So for the scenario I suggested at the top where I need to translate my private 192.x.x.x into a 10.x.x.x and present that 10.x.x.x to the other side, I need something like NAT Static (inside,outside) 10.x.x.x 192.x.x.x?
I have copied my computer's time in the router time setup under Time in the "tools" section of the router setup. After a few days of the router being up without a hard restart, it has lost 10 minutes somehow. I went to the logs and cleared them out and then looked at the entry showing that the log was cleared and looked at my computer clock and the time stamp of the log entry, and it was 10 minutes slower than my computer clock that I had originally set it from. I have a clock plugged in by the computer, and my computer always matches the clock that it plugged in, so I know it isn't my computer loosing time. What is going on here? Why does the router loose the correct time after it has been up and not unplugged or rebooted at all? I know that the router will loose the time if you unplug it, but this isn't the case here.
View 5 Replies View RelatedI'm trying to connect my Xbox 360 to Live by bridging my computer's wireless connection. I've done this before for a friend in a different city and it worked fine, and I felt very proud of myself for doing so. However when I try to connect here, the modem won't assign my Xbox an IP address. I've been into ipconfig/all and tried to manually assign the same IP address to the Xbox but to no avail. Same deal with the alternate MAC address option.
To speed things along here's the readout from my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersSamsung>ipconfig/all
[Code].....
I need to connect from an inside host to a host located in the DMZ zone for DNS queries. The host in the DMZ zone has a static NAT to the outside. The point now is that I would like to connect from inside to the NATed outside address, means to the public Internet address.
Inside host: 10.0.0.1 -> PAT for 10.0.0.0/8 to 20.0.0.254 (Outside Interface)
DMZ host: 192.168.1.1 -> NAT to outside to 20.0.0.1
The traffic should be 10.0.0.1 udp>1024 to 20.0.0.1 udp=53. The source IP address on the outside interface now is 20.0.0.254 (according to the PAT), the destination IP address 20.0.0.1. The DNS reply from 20.0.0.1 should go back now to 20.0.0.254 and then to the inside host 10.0.0.1.
I know that on the PIX it was not possible, to have outgoing traffic on the outside interface which immediately enters again the same interface. Can I realize this scenario with the ASA 8.4(3) release now?
I have an ASA5505 with 8.4 software used on a business DSL account.This means I am running PPPoE session to the provider and am then given an Inside Global subnet /29.I have various servers NATed to specific IP's then have the DHCP users NAT with overload to another of my inside global addresses. When I try to establish an IPSEC tunnel to any of my inside globals and monitor I get an access denied message but there is nothing that is blocking.If I determine my PPPoE IP address I am able to extablish a IPSEC session to that but cannot exchange traffic. Not that I want to use that IP anyway because that PPPoE Session IP changes and only my inside globals are static.I spent several hours on this and cannot put my finger on it. Do I need to allow VPN to the INSIDE interface?
View 2 Replies View RelatedI have a cisco asa 5505 and i need a public ip address on the inside of my network without NAT. for example: I can create a static nat translation rule, but this is not what i need.
isp -> x.x.x.1 /29 (outside asa) (inside network) x.x.x.2 /29
Is this possible?
I am trying to set up a d-link router with a modem provided by time warner cable. I've powered down, reset the router, and I've put it on dynamic settings (sorry if that's incorrect terminology... not a comp. buff). I can't get my wireless to connect to internet.
View 1 Replies View RelatedI am trying to get two external addresses to PAT to different ports on the same address in the dmz.
Object NAT is configured as follows:
object network Obj-192.168.1.20-1
nat (dmz,outside) static Obj-External-1 service tcp https https
object network Onj-192.168.1.20-2
nat (dmz,outside) static Obj-External-2 service tcp 2000 https
Obj-192.168.1.20-1 and Obj-192.168.1.20-2 contain the same host address.
The idea being that traffic destined for Obj-External-1 on port 443 will be forwarded to Obj-192.168.1.20-1 on port 443. Traffic for Obj-External-2 on port 443 will be forwarded to Obj-192.168.20-2 on port 2000.
Traffic for the first object, Obj-192.168.1.20-1, works but traffic for the second does not.
I have a handheld device that will be used for inventory outside of our office. It has 3g capabilities. Is there anyway I can permit traffic from this device from the outside world coming into my network? I need to open a couple of ports so it can hit the server. But I have no intention to open these ports up to the entire world. I use an ASA 5520 with a managed router from our provider. I looked around on the Cisco site and the only information I found was for permitting and denying traffic from devices that are within the network.
View 2 Replies View RelatedI have a newly aquired asa 5505 that I just set up to the bare minimum configurations. I followed a cisco paper on how to create a "remote access vpn" setup for ipsec. I can sucessfully connect and establish a VPN, but when I try to access an inside resource from the vpn address, the asa blocks it.
Specific error is:5 May 09 2012 15:17:48 305013 192.168.1.2 80 Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:192.168.1.220/53101 dst inside:192.168.1.2/80 denied due to NAT reverse path failure
Here is my config.
: Saved:ASA Version 8.2(2) !hostname asawooddomain-name wood.localenable password W/KqlBn3sSTvaD0T encryptedpasswd W/KqlBn3sSTvaD0T encryptednamesname 192.168.1.117 kylewooddesk description kyle!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip address dhcp setroute !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!boot system disk0:/asa822-k8.binftp mode passivedns server-group DefaultDNSdomain-name wood.localobject-group service rdp tcpdescription rdp accessport-object eq 3389access-list outside_access_in extended permit tcp any interface outside eq 3389 access-list outside_access_in extended permit tcp any interface outside eq 8080 access-list outside_access_in extended
[code].....
We've had issues with our Exchange 2010 server (running on ESXi 4.1) since its default gateway was changed to our new ASA 5510. They manifested as frequent Outlook client connection dropouts or as IP address conflicts whenever Exchange was rebooted. The temporary fix was to disable the Exchange server NIC, bounce the ASA and enable the server's NIC again. We saw poor performance from Exchange after a while again, but after some research and testing I realised that disabling proxyarp on the inside interface fixed the problem permanently.
However I've now realised that the client VPN no longer routes properly because proxyarp is disabled on the inside interface, so I still have a problem.
I'm trying to translate my inside network of 192.168.20.0 to my outside ISP address on ASA 5505. The ping from all hosts to 4.2.2.2 works, but it still only let's one address out to translate.My configuration is:
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
still doesn't work.
